[PATCH v3 1/9] dt-bindings: regulator: pca9450: Add properties for handling LDO5

[Conor Dooley]

On Wed, Dec 18, 2024 at 04:27:24PM +0100, Frieder Schrempf wrote:
> From: Frieder Schrempf <frieder.schrempf at kontron.de>
> 
> This reverts commit 27866e3e8a7e93494f8374f48061aa73ee46ceb2 and
> implements a new future-proof way of handling the mismatch between
> the PMIC driver and the hardware for LDO5.
> 
> It turned out that this feature was implemented based on the wrong
> assumption that the SD_VSEL signal needs to be controlled as GPIO
> in any case.
> 
> In fact the straight-forward approach is to mux the signal as
> USDHC_VSELECT and let the USDHC controller do the job.
> 
> Most users never even used this property and the few who did have
> been or are getting migrated to the alternative approach.
> 
> In order to know the current status (which of the two control
> registers is used) for the LDO5 regulator, we need to route back the
> USDHC_VSELECT signal by setting the SION bit in the IOMUX.
> 
> By adding the according GPIO as sd-vsel-gpios to the LDO5 node, we
> allow the regulator driver to sample the current status of the
> SD_VSEL signal that is used to select the correct control register.
> 
> The SD_VSEL on the PMIC is always an input. It's driven by the SoC's
> VSELECT signal (controlled by the USDHC controller) and we use the
> SION bit in the IOMUX to internally loop back the signal in order to
> sample it using the GPIO.
> 
> As the SD_VSEL pin is directly routed to the LDO5 regulator in the
> PMIC, make the sd-vsel-gpios property part of the LDO5 node.
> 
> SoC                                  PMIC
> +-----------------------+           +-------------------+
> |                       |           |                   |
> |                       |           |                   |
> |  GPIO <----------+    |           |                   |
> |                  |    |    SD_VSEL|   +-------+       |
> |  USDHC_VSELECT ->+------------------->| LDO5  |       |
> |                       |           |   +-------+       |
> |                       |           |                   |
> +-----------------------+           +-------------------+
> 
> For boards which have the SD_VSEL tied to a fixed low level, we add
> 'nxp,sd-vsel-fixed-low'. The voltage of LDO5 is therefore only controlled
> by writing to the LDO5CTRL_L register.
> 
> If none of 'nxp,sd-vsel-fixed-low' or 'sd-vsel-gpios' is set, we keep
> the same behavior as before. The driver assumes that SD_VSEL is tied
> high and the LDO5CTRL_H register can be used, which is in fact not true
> for all known boards and works merely by chance.
> 
> Signed-off-by: Frieder Schrempf <frieder.schrempf at kontron.de>

Reviewed-by: Conor Dooley <conor.dooley at microchip.com>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 228 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20241218/8d695f9b/attachment.sig>