[PATCH] drm/msm/a6xx: Skip gpu secure fw load in EL2 mode

[Dmitry Baryshkov]

On Wed, Dec 11, 2024 at 01:06:58PM +0530, Pavan Kondeti wrote:
> +devicetree
> 
> On Tue, Dec 10, 2024 at 07:43:19PM -0800, Rob Clark wrote:
> > On Tue, Dec 10, 2024 at 7:08 PM Akhil P Oommen <quic_akhilpo at quicinc.com> wrote:
> > >
> > > On 12/11/2024 6:43 AM, Bjorn Andersson wrote:
> > > > On Tue, Dec 10, 2024 at 02:22:27AM +0530, Akhil P Oommen wrote:
> > > >> On 12/10/2024 1:24 AM, Rob Clark wrote:
> > > >>> On Mon, Dec 9, 2024 at 12:20 AM Akhil P Oommen <quic_akhilpo at quicinc.com> wrote:
> > > >>>>
> > > >>>> When kernel is booted in EL2, SECVID registers are accessible to the
> > > >>>> KMD. So we can use that to switch GPU's secure mode to avoid dependency
> > > >>>> on Zap firmware. Also, we can't load a secure firmware without a
> > > >>>> hypervisor that supports it.
> > > >>>
> > > >>> Shouldn't we do this based on whether zap node is in dtb (and not disabled)?
> > > >>
> > > >> This is better, isn't it? Otherwise, multiple overlays should be
> > > >> maintained for each soc/board since EL2 can be toggled from bootloader.
> > > >> And this feature is likely going to be more widely available.
> > > >>
> > > >
> > > > The DeviceTree passed to the OS needs to describe the world that said OS
> > > > is going to operate in. If you change the world you need to change the
> > > > description.
> > > > There are several other examples where this would be necessary
> > > > (remoteproc and watchdog to name two examples from the Qualcomm upstream
> > > > world).
> > >
> > > But basic things work without those changes, right? For eg: Desktop UI
> > 
> > It isn't really so much about whether certain use-cases can work with
> > a sub-optimal description of the hw (where in this case "hw" really
> > means "hw plus how the fw allows things to look to the HLOS").. It is
> > more about the hw/fw/whatever providing an accurate description of
> > what things look like to the HLOS.
> > 
> > I'm leaning more towards the hw+fw providing HLOS an accurate view...
> > and the fact that that carries over into other areas of dtb (ie. it
> > isn't the only thing that slbounce needs to patch, as I previously
> > mentioned) reinforces my view there.  This seems like a thing to fix
> > in fw/bootloader tbh.
> > 
> 
> Thanks Rob and Bjorn for your inputs. At the moment, we don't have
> capability in our bootloader to apply a *specific* overlay when Linux
> kernel is starteed in EL, this is making GPU non-functional. This patch
> from Akhil fixes the problem without depending on the bootloader.
> 
> From this discussion, I understand that it is recommended to provide
> HW+FW view in dT correctly instead of doing runtime checks in the
> kernel. We can take this as a requirement to the bootloader.
> 
> I would like to check how we should proceed with overlay. Should we
> submit dtso upstream and let bootloader apply the overlay at runtime or
> this whole overlay needs to be maintained in the bootloader. Also,
> Should we build all board dtb for EL2 as well or just leave it at compiling
> the EL2 dtbo (one per SoC)?

It doesn't have to be a dtbo. Instead you might just patch the DT
(Ideally via the https://github.com/U-Boot-EFI/EFI_DT_FIXUP_PROTOCOL).
I think the bootloader already changes the DT (by fixing memory sizes,
etc), so enabling or disabling ZAP & fixing several other bits and
pieces sounds logical.

-- 
With best wishes
Dmitry