[PATCH v2 4/5] clk: meson: add support for the A5 SoC PLL clock
Xianwei Zhao
xianwei.zhao at amlogic.com
Tue Dec 10 23:53:57 PST 2024
Hi Jerome,
Thanks for your reply.
On 2024/11/26 00:51, Jerome Brunet wrote:
> [ EXTERNAL EMAIL ]
>
> On Wed 20 Nov 2024 at 15:01, Xianwei Zhao via B4 Relay <devnull+xianwei.zhao.amlogic.com at kernel.org> wrote:
>
>> From: Chuan Liu <chuan.liu at amlogic.com>
>>
>> Add the PLL clock controller driver for the Amlogic A5 SoC family.
>>
>> Signed-off-by: Chuan Liu <chuan.liu at amlogic.com>
>> Signed-off-by: Xianwei Zhao <xianwei.zhao at amlogic.com>
>> ---
>> drivers/clk/meson/Kconfig | 14 ++
>> drivers/clk/meson/Makefile | 1 +
>> drivers/clk/meson/a5-pll.c | 543 +++++++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 558 insertions(+)
>>
>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>> index 78f648c9c97d..3c97b3a1649d 100644
>> --- a/drivers/clk/meson/Kconfig
>> +++ b/drivers/clk/meson/Kconfig
>> @@ -132,6 +132,20 @@ config COMMON_CLK_A1_PERIPHERALS
>> device, A1 SoC Family. Say Y if you want A1 Peripherals clock
>> controller to work.
>>
>> +config COMMON_CLK_A5_PLL
>> + tristate "Amlogic A5 PLL clock controller"
>> + depends on ARM64
>> + default y
>> + imply COMMON_CLK_SCMI
>> + select COMMON_CLK_MESON_REGMAP
>> + select COMMON_CLK_MESON_PLL
>> + select COMMON_CLK_MESON_MPLL
>> + select COMMON_CLK_MESON_CLKC_UTILS
>> + help
>> + Support for the PLL clock controller on Amlogic AV40x device, AKA A5.
>
> What is an AV40x ? if it is a SoC that's alright.
> If it is a board, then it is not Ok. The driver does not support a
> single board, does it ?
>
It is a board, Will modify.
>> + Say Y if you want the board to work, because PLLs are the parent
>> + of most peripherals.
>> +
>> config COMMON_CLK_C3_PLL
>> tristate "Amlogic C3 PLL clock controller"
>> depends on ARM64
>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>> index bc56a47931c1..fc4b8a723145 100644
>> --- a/drivers/clk/meson/Makefile
>> +++ b/drivers/clk/meson/Makefile
>> @@ -20,6 +20,7 @@ obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
>> obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>> obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
>> obj-$(CONFIG_COMMON_CLK_A1_PERIPHERALS) += a1-peripherals.o
>> +obj-$(CONFIG_COMMON_CLK_A5_PLL) += a5-pll.o
>> obj-$(CONFIG_COMMON_CLK_C3_PLL) += c3-pll.o
>> obj-$(CONFIG_COMMON_CLK_C3_PERIPHERALS) += c3-peripherals.o
>> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
>> diff --git a/drivers/clk/meson/a5-pll.c b/drivers/clk/meson/a5-pll.c
>> new file mode 100644
>> index 000000000000..f18700dfd055
>> --- /dev/null
>> +++ b/drivers/clk/meson/a5-pll.c
>> @@ -0,0 +1,543 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +/*
>> + * Amlogic A5 PLL Controller Driver
>> + *
>> + * Copyright (c) 2024 Amlogic, inc.
>> + * Author: Chuan Liu <chuan.liu at amlogic.com>
>> + */
>> +
>> +#include <linux/clk-provider.h>
>> +#include <linux/platform_device.h>
>> +#include "clk-regmap.h"
>> +#include "clk-pll.h"
>> +#include "clk-mpll.h"
>> +#include "meson-clkc-utils.h"
>> +#include <dt-bindings/clock/amlogic,a5-pll-clkc.h>
>> +
>> +#define ANACTRL_GP0PLL_CTRL0 0x80
>> +#define ANACTRL_GP0PLL_CTRL1 0x84
>> +#define ANACTRL_GP0PLL_CTRL2 0x88
>> +#define ANACTRL_GP0PLL_CTRL3 0x8c
>> +#define ANACTRL_GP0PLL_CTRL4 0x90
>> +#define ANACTRL_GP0PLL_CTRL5 0x94
>> +#define ANACTRL_GP0PLL_CTRL6 0x98
>> +#define ANACTRL_HIFIPLL_CTRL0 0x100
>> +#define ANACTRL_HIFIPLL_CTRL1 0x104
>> +#define ANACTRL_HIFIPLL_CTRL2 0x108
>> +#define ANACTRL_HIFIPLL_CTRL3 0x10c
>> +#define ANACTRL_HIFIPLL_CTRL4 0x110
>> +#define ANACTRL_HIFIPLL_CTRL5 0x114
>> +#define ANACTRL_HIFIPLL_CTRL6 0x118
>> +#define ANACTRL_MPLL_CTRL0 0x180
>> +#define ANACTRL_MPLL_CTRL1 0x184
>> +#define ANACTRL_MPLL_CTRL2 0x188
>> +#define ANACTRL_MPLL_CTRL3 0x18c
>> +#define ANACTRL_MPLL_CTRL4 0x190
>> +#define ANACTRL_MPLL_CTRL5 0x194
>> +#define ANACTRL_MPLL_CTRL6 0x198
>> +#define ANACTRL_MPLL_CTRL7 0x19c
>> +#define ANACTRL_MPLL_CTRL8 0x1a0
>
> Same question as usual, is there clocks and *ONLY* clock between 0x0 and
> 0x1a0 ?
>
> If you can guarantee that, you'll need to split the controller into
> multiple devices.
>
Between 0x0 and 0x5c are fix_pll and sys_pll. These two plls are
processed in bl31 due to security restrictions. Besides, there are
no registers of other modules interspersed in it.
>> +
>> +static struct clk_fixed_factor mpll_prediv = {
>> + .mult = 1,
>> + .div = 2,
>> + .hw.init = &(struct clk_init_data){
>> + .name = "mpll_prediv",
>> + .ops = &clk_fixed_factor_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "fix_dco"
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static const struct reg_sequence mpll0_init_regs[] = {
>> + { .reg = ANACTRL_MPLL_CTRL2, .def = 0x40000033 },
>> +};
>> +
>> +static struct clk_regmap mpll0_div = {
>> + .data = &(struct meson_clk_mpll_data){
>> + .sdm = {
>> + .reg_off = ANACTRL_MPLL_CTRL1,
>> + .shift = 0,
>> + .width = 14,
>> + },
>> + .sdm_en = {
>> + .reg_off = ANACTRL_MPLL_CTRL1,
>> + .shift = 30,
>> + .width = 1,
>> + },
>> + .n2 = {
>> + .reg_off = ANACTRL_MPLL_CTRL1,
>> + .shift = 20,
>> + .width = 9,
>> + },
>> + .ssen = {
>> + .reg_off = ANACTRL_MPLL_CTRL1,
>> + .shift = 29,
>> + .width = 1,
>> + },
>> + .init_regs = mpll0_init_regs,
>> + .init_count = ARRAY_SIZE(mpll0_init_regs),
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "mpll0_div",
>> + .ops = &meson_clk_mpll_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &mpll_prediv.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap mpll0 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_MPLL_CTRL1,
>> + .bit_idx = 31,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "mpll0",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) { &mpll0_div.hw },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static const struct reg_sequence mpll1_init_regs[] = {
>> + { .reg = ANACTRL_MPLL_CTRL4, .def = 0x40000033 },
>> +};
>> +
>> +static struct clk_regmap mpll1_div = {
>> + .data = &(struct meson_clk_mpll_data){
>> + .sdm = {
>> + .reg_off = ANACTRL_MPLL_CTRL3,
>> + .shift = 0,
>> + .width = 14,
>> + },
>> + .sdm_en = {
>> + .reg_off = ANACTRL_MPLL_CTRL3,
>> + .shift = 30,
>> + .width = 1,
>> + },
>> + .n2 = {
>> + .reg_off = ANACTRL_MPLL_CTRL3,
>> + .shift = 20,
>> + .width = 9,
>> + },
>> + .ssen = {
>> + .reg_off = ANACTRL_MPLL_CTRL3,
>> + .shift = 29,
>> + .width = 1,
>> + },
>> + .init_regs = mpll1_init_regs,
>> + .init_count = ARRAY_SIZE(mpll1_init_regs),
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "mpll1_div",
>> + .ops = &meson_clk_mpll_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &mpll_prediv.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap mpll1 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_MPLL_CTRL3,
>> + .bit_idx = 31,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "mpll1",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) { &mpll1_div.hw },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static const struct reg_sequence mpll2_init_regs[] = {
>> + { .reg = ANACTRL_MPLL_CTRL6, .def = 0x40000033 },
>> +};
>> +
>> +static struct clk_regmap mpll2_div = {
>> + .data = &(struct meson_clk_mpll_data){
>> + .sdm = {
>> + .reg_off = ANACTRL_MPLL_CTRL5,
>> + .shift = 0,
>> + .width = 14,
>> + },
>> + .sdm_en = {
>> + .reg_off = ANACTRL_MPLL_CTRL5,
>> + .shift = 30,
>> + .width = 1,
>> + },
>> + .n2 = {
>> + .reg_off = ANACTRL_MPLL_CTRL5,
>> + .shift = 20,
>> + .width = 9,
>> + },
>> + .ssen = {
>> + .reg_off = ANACTRL_MPLL_CTRL5,
>> + .shift = 29,
>> + .width = 1,
>> + },
>> + .init_regs = mpll2_init_regs,
>> + .init_count = ARRAY_SIZE(mpll2_init_regs),
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "mpll2_div",
>> + .ops = &meson_clk_mpll_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &mpll_prediv.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap mpll2 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_MPLL_CTRL5,
>> + .bit_idx = 31,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "mpll2",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) { &mpll2_div.hw },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static const struct reg_sequence mpll3_init_regs[] = {
>> + { .reg = ANACTRL_MPLL_CTRL8, .def = 0x40000033 },
>> +};
>> +
>> +static struct clk_regmap mpll3_div = {
>> + .data = &(struct meson_clk_mpll_data){
>> + .sdm = {
>> + .reg_off = ANACTRL_MPLL_CTRL7,
>> + .shift = 0,
>> + .width = 14,
>> + },
>> + .sdm_en = {
>> + .reg_off = ANACTRL_MPLL_CTRL7,
>> + .shift = 30,
>> + .width = 1,
>> + },
>> + .n2 = {
>> + .reg_off = ANACTRL_MPLL_CTRL7,
>> + .shift = 20,
>> + .width = 9,
>> + },
>> + .ssen = {
>> + .reg_off = ANACTRL_MPLL_CTRL7,
>> + .shift = 29,
>> + .width = 1,
>> + },
>> + .init_regs = mpll3_init_regs,
>> + .init_count = ARRAY_SIZE(mpll3_init_regs),
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "mpll3_div",
>> + .ops = &meson_clk_mpll_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &mpll_prediv.hw
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap mpll3 = {
>> + .data = &(struct clk_regmap_gate_data){
>> + .offset = ANACTRL_MPLL_CTRL7,
>> + .bit_idx = 31,
>> + },
>> + .hw.init = &(struct clk_init_data){
>> + .name = "mpll3",
>> + .ops = &clk_regmap_gate_ops,
>> + .parent_hws = (const struct clk_hw *[]) { &mpll3_div.hw },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static const struct reg_sequence gp0_init_regs[] = {
>> + { .reg = ANACTRL_GP0PLL_CTRL2, .def = 0x00000000 },
>> + { .reg = ANACTRL_GP0PLL_CTRL3, .def = 0x6a295c00 },
>> + { .reg = ANACTRL_GP0PLL_CTRL4, .def = 0x65771290 },
>> + { .reg = ANACTRL_GP0PLL_CTRL5, .def = 0x3927200a },
>> + { .reg = ANACTRL_GP0PLL_CTRL6, .def = 0x54540000 }
>> +};
>> +
>> +static const struct pll_mult_range gp0_pll_mult_range = {
>> + .min = 125,
>> + .max = 250,
>> +};
>> +
>> +static struct clk_regmap gp0_pll_dco = {
>> + .data = &(struct meson_clk_pll_data) {
>> + .en = {
>> + .reg_off = ANACTRL_GP0PLL_CTRL0,
>> + .shift = 28,
>> + .width = 1,
>> + },
>> + .m = {
>> + .reg_off = ANACTRL_GP0PLL_CTRL0,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .frac = {
>> + .reg_off = ANACTRL_GP0PLL_CTRL1,
>> + .shift = 0,
>> + .width = 17,
>> + },
>> + .n = {
>> + .reg_off = ANACTRL_GP0PLL_CTRL0,
>> + .shift = 10,
>> + .width = 5,
>> + },
>> + .l = {
>> + .reg_off = ANACTRL_GP0PLL_CTRL0,
>> + .shift = 31,
>> + .width = 1,
>> + },
>> + .rst = {
>> + .reg_off = ANACTRL_GP0PLL_CTRL0,
>> + .shift = 29,
>> + .width = 1,
>> + },
>> + .range = &gp0_pll_mult_range,
>> + .init_regs = gp0_init_regs,
>> + .init_count = ARRAY_SIZE(gp0_init_regs),
>> + .frac_max = 100000,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "gp0_pll_dco",
>> + .ops = &meson_clk_pll_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal_24m",
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +/* The maximum frequency divider supports is 32, not 128(2^7) */
>> +static const struct clk_div_table gp0_pll_od_table[] = {
>> + { 0, 1 },
>> + { 1, 2 },
>> + { 2, 4 },
>> + { 3, 8 },
>> + { 4, 16 },
>> + { 5, 32 },
>> + { /* sentinel */ }
>> +};
>> +
>> +static struct clk_regmap gp0_pll = {
>> + .data = &(struct clk_regmap_div_data) {
>> + .offset = ANACTRL_GP0PLL_CTRL0,
>> + .shift = 16,
>> + .width = 3,
>> + .table = gp0_pll_od_table,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "gp0_pll",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &gp0_pll_dco.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static const struct reg_sequence hifi_init_regs[] = {
>> + { .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00000000 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x6a295c00 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x65771290 },
>> + { .reg = ANACTRL_HIFIPLL_CTRL5, .def = 0x3927200a },
>> + { .reg = ANACTRL_HIFIPLL_CTRL6, .def = 0x54540000 }
>> +};
>> +
>> +static const struct pll_mult_range hifi_pll_mult_range = {
>> + .min = 125,
>> + .max = 250,
>> +};
>> +
>> +static struct clk_regmap hifi_pll_dco = {
>> + .data = &(struct meson_clk_pll_data) {
>> + .en = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 28,
>> + .width = 1,
>> + },
>> + .m = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .frac = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL1,
>> + .shift = 0,
>> + .width = 17,
>> + },
>> + .n = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 10,
>> + .width = 5,
>> + },
>> + .l = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 31,
>> + .width = 1,
>> + },
>> + .rst = {
>> + .reg_off = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 29,
>> + .width = 1,
>> + },
>> + .range = &hifi_pll_mult_range,
>> + .init_regs = hifi_init_regs,
>> + .init_count = ARRAY_SIZE(hifi_init_regs),
>> + .frac_max = 100000,
>> + /* NOTE: The original design of hifi_pll is to provide
>> + * clock for audio, which requires clock accuracy.
>> + * Therefore, flag CLK_MESON_PLL_ROUND_CLOSEST is added
>> + * to make the output frequency of hifi_pll closer to
>> + * the target frequency.
>> + */
>
> The comment format is incorrect. not quite sure the commnet itself is useful.
>
Delete this comment in the next version.
>> + .flags = CLK_MESON_PLL_ROUND_CLOSEST,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "hifi_pll_dco",
>> + .ops = &meson_clk_pll_ops,
>> + .parent_data = &(const struct clk_parent_data) {
>> + .fw_name = "xtal_24m",
>> + },
>> + .num_parents = 1,
>> + },
>> +};
>> +
>> +static struct clk_regmap hifi_pll = {
>> + .data = &(struct clk_regmap_div_data) {
>> + .offset = ANACTRL_HIFIPLL_CTRL0,
>> + .shift = 16,
>> + /* NOTE: The actual reserved bit width of the od (output
>> + * divider) of hifi_pll is 3 bit, but its actual maximum
>> + * effective divider factor is 8. It can just use 2 bit and add
>> + * flag CLK_DIVIDER_POWER_OF_TWO (max_div = 2^3 = 8).
>> + */
>
> Same here
Delete this comment in the next version.
>
>> + .width = 2,
>
> ... yet the width is 2 ??
>
>> + .flags = CLK_DIVIDER_POWER_OF_TWO,
>> + },
>> + .hw.init = &(struct clk_init_data) {
>> + .name = "hifi_pll",
>> + .ops = &clk_regmap_divider_ops,
>> + .parent_hws = (const struct clk_hw *[]) {
>> + &hifi_pll_dco.hw
>> + },
>> + .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> + },
>> +};
>> +
>> +static struct clk_hw *a5_pll_hw_clks[] = {
>> + [CLKID_MPLL_PREDIV] = &mpll_prediv.hw,
>> + [CLKID_MPLL0_DIV] = &mpll0_div.hw,
>> + [CLKID_MPLL0] = &mpll0.hw,
>> + [CLKID_MPLL1_DIV] = &mpll1_div.hw,
>> + [CLKID_MPLL1] = &mpll1.hw,
>> + [CLKID_MPLL2_DIV] = &mpll2_div.hw,
>> + [CLKID_MPLL2] = &mpll2.hw,
>> + [CLKID_MPLL3_DIV] = &mpll3_div.hw,
>> + [CLKID_MPLL3] = &mpll3.hw,
>> + [CLKID_GP0_PLL_DCO] = &gp0_pll_dco.hw,
>> + [CLKID_GP0_PLL] = &gp0_pll.hw,
>> + [CLKID_HIFI_PLL_DCO] = &hifi_pll_dco.hw,
>> + [CLKID_HIFI_PLL] = &hifi_pll.hw
>> +};
>> +
>> +/* Convenience table to populate regmap in .probe */
>> +static struct clk_regmap *const a5_pll_clk_regmaps[] = {
>> + &mpll0_div,
>> + &mpll0,
>> + &mpll1_div,
>> + &mpll1,
>> + &mpll2_div,
>> + &mpll2,
>> + &mpll3_div,
>> + &mpll3,
>> + &gp0_pll_dco,
>> + &gp0_pll,
>> + &hifi_pll_dco,
>> + &hifi_pll
>> +};
>> +
>> +static const struct regmap_config clkc_regmap_config = {
>> + .reg_bits = 32,
>> + .val_bits = 32,
>> + .reg_stride = 4,
>> + .max_register = ANACTRL_MPLL_CTRL8,
>> +};
>> +
>> +static struct meson_clk_hw_data a5_pll_clks = {
>> + .hws = a5_pll_hw_clks,
>> + .num = ARRAY_SIZE(a5_pll_hw_clks),
>> +};
>> +
>> +static int aml_a5_pll_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct regmap *regmap;
>> + void __iomem *base;
>> + int clkid, ret, i;
>> +
>> + base = devm_platform_ioremap_resource(pdev, 0);
>> + if (IS_ERR(base))
>> + return PTR_ERR(base);
>> +
>> + regmap = devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
>> + if (IS_ERR(regmap))
>> + return PTR_ERR(regmap);
>> +
>> + /* Populate regmap for the regmap backed clocks */
>> + for (i = 0; i < ARRAY_SIZE(a5_pll_clk_regmaps); i++)
>> + a5_pll_clk_regmaps[i]->map = regmap;
>> +
>> + for (clkid = 0; clkid < a5_pll_clks.num; clkid++) {
>> + /* array might be sparse */
>> + if (!a5_pll_clks.hws[clkid])
>> + continue;
>> +
>> + ret = devm_clk_hw_register(dev, a5_pll_clks.hws[clkid]);
>> + if (ret) {
>> + dev_err(dev, "Clock registration failed\n");
>> + return ret;
>> + }
>> + }
>> +
>> + return devm_of_clk_add_hw_provider(dev, meson_clk_hw_get,
>> + &a5_pll_clks);
>> +}
>> +
>> +static const struct of_device_id a5_pll_clkc_match_table[] = {
>> + {
>> + .compatible = "amlogic,a5-pll-clkc",
>> + },
>> + {}
>> +};
>> +MODULE_DEVICE_TABLE(of, a5_pll_clkc_match_table);
>> +
>> +static struct platform_driver a5_pll_driver = {
>> + .probe = aml_a5_pll_probe,
>> + .driver = {
>> + .name = "a5-pll-clkc",
>> + .of_match_table = a5_pll_clkc_match_table,
>> + },
>> +};
>> +module_platform_driver(a5_pll_driver);
>> +
>> +MODULE_DESCRIPTION("Amlogic A5 PLL Clock Controller driver");
>> +MODULE_AUTHOR("Chuan Liu <chuan.liu at amlogic.com>");
>> +MODULE_LICENSE("GPL");
>
> --
> Jerome
More information about the linux-arm-kernel
mailing list