[PATCH v2 4/5] arm64: dts: exynos: gs101-oriole: enable Maxim max77759 TCPCi

[André Draszik]

On Pixel 6 (and Pro), a max77759 companion PMIC for USB Type-C
applications is used, which contains four functional blocks (at
distinct I2C addresses):
  * top (including GPIO)
  * charger
  * fuel gauge
  * TCPCi

While in the same package, TCPCi and Fuel Gauge have separate I2C
addresses, interrupt lines and interrupt status registers and can be
treated independently.

The TCPCi is required to detect and handle connector orientation in
Pixel's USB PHY driver, and to configure the USB controller's role
(host vs device).

This change adds the TCPCi part as it can be independent and doesn't
need a top-level MFD.

Signed-off-by: André Draszik <andre.draszik at linaro.org>

---
v2:
* compatible has changed to maxim,max77759-tcpci
* clarify that GPIO is actually part of 'top' in commit message, not
  separate
---
 arch/arm64/boot/dts/exynos/google/gs101-oriole.dts | 99 ++++++++++++++++++++++
 1 file changed, 99 insertions(+)

diff --git a/arch/arm64/boot/dts/exynos/google/gs101-oriole.dts b/arch/arm64/boot/dts/exynos/google/gs101-oriole.dts
index 387fb779bd29..a5cbf1e10c7b 100644
--- a/arch/arm64/boot/dts/exynos/google/gs101-oriole.dts
+++ b/arch/arm64/boot/dts/exynos/google/gs101-oriole.dts
@@ -10,6 +10,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/usb/pd.h>
 #include "gs101-pinctrl.h"
 #include "gs101.dtsi"
 
@@ -90,6 +91,84 @@ eeprom: eeprom at 50 {
 &hsi2c_12 {
 	status = "okay";
 	/* TODO: add the devices once drivers exist */
+
+	usb-typec at 25 {
+		compatible = "maxim,max77759-tcpci", "maxim,max33359";
+		reg = <0x25>;
+		interrupts-extended = <&gpa8 2 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&typec_int>;
+		pinctrl-names = "default";
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			data-role = "dual";
+			power-role = "dual";
+			self-powered;
+			try-power-role = "sink";
+			op-sink-microwatt = <2600000>;
+			new-source-frs-typec-current = <FRS_5V_1P5A>;
+			slow-charger-loop;
+			/*
+			 * max77759 operating in reverse boost mode (0xA) can
+			 * source up to 1.5A while extboost can only do ~1A.
+			 * Since extboost is the primary path, advertise 900mA.
+			 */
+			source-pdos = <PDO_FIXED(5000, 900,
+						 (PDO_FIXED_SUSPEND
+						  | PDO_FIXED_USB_COMM
+						  | PDO_FIXED_DATA_SWAP
+						  | PDO_FIXED_DUAL_ROLE))>;
+			sink-pdos = <PDO_FIXED(5000, 3000,
+					       (PDO_FIXED_DATA_SWAP
+						| PDO_FIXED_USB_COMM
+						| PDO_FIXED_HIGHER_CAP
+						| PDO_FIXED_DUAL_ROLE))
+				     PDO_FIXED(9000, 2200, 0)
+				     PDO_PPS_APDO(5000, 11000, 3000)>;
+			sink-vdos = <VDO_IDH(1, 1, IDH_PTYPE_PERIPH, 0,
+					     IDH_PTYPE_DFP_HOST, 2, 0x18d1)
+				     VDO_CERT(0x0)
+				     VDO_PRODUCT(0x4ee1, 0x0)
+				     VDO_UFP(UFP_VDO_VER1_2,
+					     (DEV_USB2_CAPABLE
+					      | DEV_USB3_CAPABLE),
+					     UFP_RECEPTACLE, 0,
+					     AMA_VCONN_NOT_REQ, 0,
+					     UFP_ALTMODE_NOT_SUPP,
+					     UFP_USB32_GEN1)
+				     /* padding */ 0
+				     VDO_DFP(DFP_VDO_VER1_1,
+					     (HOST_USB2_CAPABLE
+					      | HOST_USB3_CAPABLE),
+					     DFP_RECEPTACLE, 0)>;
+			sink-vdos-v1 = <VDO_IDH(1, 1, IDH_PTYPE_PERIPH, 0,
+						0, 0, 0x18d1)
+					VDO_CERT(0x0)
+					VDO_PRODUCT(0x4ee1, 0x0)>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port at 0 {
+					reg = <0>;
+
+					usbc0_orien_sw: endpoint {
+						remote-endpoint = <&usbdrd31_phy_orien_switch>;
+					};
+				};
+
+				port at 1 {
+					reg = <1>;
+
+					usbc0_role_sw: endpoint {
+						remote-endpoint = <&usbdrd31_dwc3_role_switch>;
+					};
+				};
+			};
+		};
+	};
 };
 
 &pinctrl_far_alive {
@@ -106,6 +185,13 @@ key_volup: key-volup-pins {
 		samsung,pin-pud = <GS101_PIN_PULL_NONE>;
 		samsung,pin-drv = <GS101_PIN_DRV_2_5_MA>;
 	};
+
+	typec_int: typec-int-pins {
+		samsung,pins = "gpa8-2";
+		samsung,pin-function = <GS101_PIN_FUNC_EINT>;
+		samsung,pin-pud = <GS101_PIN_PULL_UP>;
+		samsung,pin-drv = <GS101_PIN_DRV_2_5_MA>;
+	};
 };
 
 &pinctrl_gpio_alive {
@@ -142,9 +228,16 @@ &usbdrd31_dwc3 {
 	role-switch-default-mode = "peripheral";
 	maximum-speed = "super-speed-plus";
 	status = "okay";
+
+	port {
+		usbdrd31_dwc3_role_switch: endpoint {
+			remote-endpoint = <&usbc0_role_sw>;
+		};
+	};
 };
 
 &usbdrd31_phy {
+	orientation-switch;
 	/* TODO: Update these once PMIC is implemented */
 	pll-supply = <&reg_placeholder>;
 	dvdd-usb20-supply = <&reg_placeholder>;
@@ -153,6 +246,12 @@ &usbdrd31_phy {
 	vdda-usbdp-supply = <&reg_placeholder>;
 	vddh-usbdp-supply = <&reg_placeholder>;
 	status = "okay";
+
+	port {
+		usbdrd31_phy_orien_switch: endpoint {
+			remote-endpoint = <&usbc0_orien_sw>;
+		};
+	};
 };
 
 &usi_uart {

-- 
2.47.0.338.g60cca15819-goog