[PATCH v2] arm64: dts: ti: k3-am64* Disable ethernet by default at SoC level

Daniel Schultz d.schultz at phytec.de
Wed Aug 28 22:49:57 PDT 2024


On 26.08.24 23:17, Logan Bristol wrote:
> Hi Daniel,
>
> On 8/26/2024 12:29 AM, Daniel Schultz wrote:
>> Hey Logan,
>>
>> my feedback is similar to Josua's.
>>
>> On 09.08.24 15:57, Logan Bristol wrote:
>>> External interfaces should be disabled at the SoC DTSI level, since
>>> the node is incomplete. Disable Ethernet switch and ports in SoC DTSI
>>> and enable them in the board DTS. If the board DTS includes a SoM DTSI
>>> that completes the node description, enable the Ethernet switch and 
>>> ports
>>> in SoM DTSI.
>>>
>>> Reflect this change in SoM DTSIs by removing ethernet port disable.
>>>
>>> Signed-off-by: Logan Bristol <logan.bristol at utexas.edu>
>>> ---
>>> Changes since v1:
>>> - Enabled cpsw3g and cpsw_port1 in SoM DTSI instead of board DTS
>>> if board DTS included SoM DTSI
>>> ---
>>>   arch/arm64/boot/dts/ti/k3-am64-main.dtsi               | 3 +++
>>>   arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi        | 6 ++----
>>>   arch/arm64/boot/dts/ti/k3-am642-evm.dts                | 3 +++
>>>   arch/arm64/boot/dts/ti/k3-am642-sk.dts                 | 3 +++
>>>   arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi            | 6 ++----
>>>   arch/arm64/boot/dts/ti/k3-am642-tqma64xxl-mbax4xxl.dts | 6 ++----
>>>   6 files changed, 15 insertions(+), 12 deletions(-)
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi b/arch/arm64/ 
>>> boot/dts/ti/k3-am64-main.dtsi
>>> index f8370dd03350..69c5af58b727 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
>>> +++ b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
>>> @@ -677,6 +677,7 @@ cpsw3g: ethernet at 8000000 {
>>>           assigned-clock-parents = <&k3_clks 13 9>;
>>>           clock-names = "fck";
>>>           power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
>>> +        status = "disabled";
>>>           dmas = <&main_pktdma 0xC500 15>,
>>>                  <&main_pktdma 0xC501 15>,
>>> @@ -701,6 +702,7 @@ cpsw_port1: port at 1 {
>>>                   phys = <&phy_gmii_sel 1>;
>>>                   mac-address = [00 00 00 00 00 00];
>>>                   ti,syscon-efuse = <&main_conf 0x200>;
>>> +                status = "disabled";
>>>               };
>>>               cpsw_port2: port at 2 {
>>> @@ -709,6 +711,7 @@ cpsw_port2: port at 2 {
>>>                   label = "port2";
>>>                   phys = <&phy_gmii_sel 2>;
>>>                   mac-address = [00 00 00 00 00 00];
>>> +                status = "disabled";
>>>               };
>>>           };
>>> diff --git a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi b/arch/ 
>>> arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
>>> index ea7c58fb67e2..6bece2fb4e95 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
>>> +++ b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
>>> @@ -185,6 +185,7 @@ AM64X_IOPAD(0x0278, PIN_INPUT, 7)    /* (C19) 
>>> EXTINTn.GPIO1_70 */
>>>   &cpsw3g {
>>>       pinctrl-names = "default";
>>>       pinctrl-0 = <&cpsw_rgmii1_pins_default>;
>>> +    status = "okay";
>>>   };
>>>   &cpsw3g_mdio {
>>> @@ -208,10 +209,7 @@ cpsw3g_phy1: ethernet-phy at 1 {
>>>   &cpsw_port1 {
>>>       phy-mode = "rgmii-rxid";
>>>       phy-handle = <&cpsw3g_phy1>;
>> The connected phy is located on the SOM and should be enabled by 
>> default.
>>> -};
>>> -
>>> -&cpsw_port2 {
>>> -    status = "disabled";
>>> +    status = "okay";
>>>   };
>>
>> This port is routed to the carrier-board. Please drop this node.
>
> I replied similarly to Josua's comments, but if cpsw_port1 is to be 
> enabled and cpsw_port2 should be dropped from this DTSI, isn't that 
> shown in this diff?

Ah, sorry. I did the same mistake :)

Acked-by: Daniel Schultz <d.schultz at phytec.de>

>
> Thank you,
> Logan Bristol
>



More information about the linux-arm-kernel mailing list