[PATCH v2 6/6] arm64: dts: ti: iot2050: Enforce DMA isolation for devices behind PCI RC
Jan Kiszka
jan.kiszka at siemens.com
Mon Aug 26 14:50:07 PDT 2024
From: Jan Kiszka <jan.kiszka at siemens.com>
Reserve a 64M memory region below the top of 1G RAM (smallest RAM size
across the series, space left for firmware carve-outs) and ensure that
all PCI devices do their DMA only inside that region. This is configured
via a restricted-dma-pool and enforced with the help of the first PVU.
Signed-off-by: Jan Kiszka <jan.kiszka at siemens.com>
---
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 32 +++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index e76828ccf21b..cc0f33e3519c 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -82,6 +82,11 @@ wdt_reset_memory_region: wdt-memory at a2200000 {
reg = <0x00 0xa2200000 0x00 0x1000>;
no-map;
};
+
+ pci_restricted_dma_region: restricted-dma at ba000000 {
+ compatible = "restricted-dma-pool";
+ reg = <0 0xba000000 0 0x4000000>;
+ };
};
leds {
@@ -571,6 +576,10 @@ seboot-backup at e80000 {
};
};
+&pcie0_rc {
+ memory-region = <&pci_restricted_dma_region>;
+};
+
&pcie1_rc {
status = "okay";
pinctrl-names = "default";
@@ -580,6 +589,8 @@ &pcie1_rc {
phys = <&serdes1 PHY_TYPE_PCIE 0>;
phy-names = "pcie-phy0";
reset-gpios = <&wkup_gpio0 27 GPIO_ACTIVE_HIGH>;
+
+ memory-region = <&pci_restricted_dma_region>;
};
&mailbox0_cluster0 {
@@ -640,3 +651,24 @@ &mcu_r5fss0 {
/* lock-step mode not supported on iot2050 boards */
ti,cluster-mode = <0>;
};
+
+&main_navss {
+ ti_pvu0: ti-pvu at 30f80000 {
+ compatible = "ti,am654-pvu";
+ reg = <0 0x30f80000 0 0x1000>,
+ <0 0x36000000 0 0x100000>;
+ reg-names = "cfg", "tlbif";
+ interrupts-extended = <&intr_main_navss 390>;
+ interrupt-names = "pvu";
+ };
+
+ ti_pvu1: ti-pvu at 30f81000 {
+ compatible = "ti,am654-pvu";
+ reg = <0 0x30f81000 0 0x1000>,
+ <0 0x36100000 0 0x100000>;
+ reg-names = "cfg", "tlbif";
+ interrupts-extended = <&intr_main_navss 389>;
+ interrupt-names = "pvu";
+ status = "disabled";
+ };
+};
--
2.43.0
More information about the linux-arm-kernel
mailing list