[PATCH 07/11] pinctrl: rp1: Implement RaspberryPi RP1 gpio support

[Krzysztof Kozlowski]

On Tue, Aug 20, 2024 at 04:36:09PM +0200, Andrea della Porta wrote:
> The RP1 is an MFD supporting a gpio controller and /pinmux/pinctrl.
> Add minimum support for the gpio only portion. The driver is in
> pinctrl folder since upcoming patches will add the pinmux/pinctrl
> support where the gpio part can be seen as an addition.
> 
> Signed-off-by: Andrea della Porta <andrea.porta at suse.com>
> ---
>  MAINTAINERS                   |   1 +
>  drivers/pinctrl/Kconfig       |  10 +
>  drivers/pinctrl/Makefile      |   1 +
>  drivers/pinctrl/pinctrl-rp1.c | 719 ++++++++++++++++++++++++++++++++++
>  4 files changed, 731 insertions(+)
>  create mode 100644 drivers/pinctrl/pinctrl-rp1.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 4ce7b049d67e..67f460c36ea1 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -19122,6 +19122,7 @@ S:	Maintained
>  F:	Documentation/devicetree/bindings/clock/raspberrypi,rp1-clocks.yaml
>  F:	Documentation/devicetree/bindings/pinctrl/raspberrypi,rp1-gpio.yaml
>  F:	drivers/clk/clk-rp1.c
> +F:	drivers/pinctrl/pinctrl-rp1.c
>  F:	include/dt-bindings/clock/rp1.h
>  F:	include/dt-bindings/misc/rp1.h
>  
> diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
> index 7e4f93a3bc7a..18bb1a8bd102 100644
> --- a/drivers/pinctrl/Kconfig
> +++ b/drivers/pinctrl/Kconfig
> @@ -565,6 +565,16 @@ config PINCTRL_MLXBF3
>  	  each pin. This driver can also be built as a module called
>  	  pinctrl-mlxbf3.
>  
> +config PINCTRL_RP1
> +	bool "Pinctrl driver for RP1"
> +	select PINMUX
> +	select PINCONF
> +	select GENERIC_PINCONF
> +	select GPIOLIB_IRQCHIP
> +	help
> +	  Enable the gpio and pinctrl/mux  driver for RaspberryPi RP1
> +	  multi function device. 
> +
>  source "drivers/pinctrl/actions/Kconfig"
>  source "drivers/pinctrl/aspeed/Kconfig"
>  source "drivers/pinctrl/bcm/Kconfig"
> diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
> index cc809669405a..f1ca23b563f6 100644
> --- a/drivers/pinctrl/Makefile
> +++ b/drivers/pinctrl/Makefile
> @@ -45,6 +45,7 @@ obj-$(CONFIG_PINCTRL_PIC32)	+= pinctrl-pic32.o
>  obj-$(CONFIG_PINCTRL_PISTACHIO)	+= pinctrl-pistachio.o
>  obj-$(CONFIG_PINCTRL_RK805)	+= pinctrl-rk805.o
>  obj-$(CONFIG_PINCTRL_ROCKCHIP)	+= pinctrl-rockchip.o
> +obj-$(CONFIG_PINCTRL_RP1)       += pinctrl-rp1.o
>  obj-$(CONFIG_PINCTRL_SCMI)	+= pinctrl-scmi.o
>  obj-$(CONFIG_PINCTRL_SINGLE)	+= pinctrl-single.o
>  obj-$(CONFIG_PINCTRL_ST) 	+= pinctrl-st.o
> diff --git a/drivers/pinctrl/pinctrl-rp1.c b/drivers/pinctrl/pinctrl-rp1.c
> new file mode 100644
> index 000000000000..c035d2014505
> --- /dev/null
> +++ b/drivers/pinctrl/pinctrl-rp1.c
> @@ -0,0 +1,719 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Driver for Raspberry Pi RP1 GPIO unit
> + *
> + * Copyright (C) 2023 Raspberry Pi Ltd.
> + *
> + * This driver is inspired by:
> + * pinctrl-bcm2835.c, please see original file for copyright information
> + */
> +
> +#include <linux/bitmap.h>
> +#include <linux/bitops.h>
> +#include <linux/bug.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/gpio/driver.h>
> +#include <linux/io.h>
> +#include <linux/irq.h>
> +#include <linux/irqdesc.h>
> +#include <linux/init.h>
> +#include <linux/of_address.h>
> +#include <linux/of.h>
> +#include <linux/of_irq.h>
> +#include <linux/platform_device.h>
> +#include <linux/seq_file.h>
> +#include <linux/spinlock.h>
> +#include <linux/types.h>

Half of these headers are not used. Drop them.

Best regards,
Krzysztof