[PATCH v4 2/5] arm64: dts: ti: k3-j784s4*: Remove bootph properties from parent nodes

Manorit Chawdhry m-chawdhry at ti.com
Wed Aug 14 00:47:29 PDT 2024


Removes bootph-* properties from parent nodes and adds bootph for other
bootloader nodes.

Also moves bootph from mcu_timer1 to mcu_timer0 as that is the one that
is used in bootloader.

Signed-off-by: Manorit Chawdhry <m-chawdhry at ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts         | 10 +---------
 arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 10 ++++++----
 2 files changed, 7 insertions(+), 13 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index ffa38f41679d..08f4791a3ee8 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -334,7 +334,6 @@ &wkup_gpio0 {
 };
 
 &main_pmx0 {
-	bootph-all;
 	main_cpsw2g_default_pins: main-cpsw2g-default-pins {
 		pinctrl-single,pins = <
 			J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
@@ -461,7 +460,6 @@ J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
 };
 
 &wkup_pmx2 {
-	bootph-all;
 	wkup_uart0_pins_default: wkup-uart0-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
@@ -577,7 +575,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
 };
 
 &wkup_pmx0 {
-	bootph-all;
 	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
@@ -597,7 +594,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
 };
 
 &wkup_pmx1 {
-	bootph-all;
 	mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
@@ -668,6 +664,7 @@ bucka12: buck12 {
 				regulator-max-microvolt = <1100000>;
 				regulator-boot-on;
 				regulator-always-on;
+				bootph-pre-ram;
 			};
 
 			bucka3: buck3 {
@@ -769,18 +766,15 @@ &ufs_wrapper {
 };
 
 &fss {
-	bootph-all;
 	status = "okay";
 };
 
 &ospi0 {
-	bootph-all;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
 
 	flash at 0 {
-		bootph-all;
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <8>;
@@ -837,13 +831,11 @@ partition at 3fc0000 {
 };
 
 &ospi1 {
-	bootph-all;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
 
 	flash at 0 {
-		bootph-all;
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
index f3a6ed1c979d..6409e702ffd4 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
@@ -7,7 +7,6 @@
 
 &cbass_mcu_wakeup {
 	sms: system-controller at 44083000 {
-		bootph-all;
 		compatible = "ti,k2g-sci";
 		ti,host-id = <12>;
 
@@ -39,7 +38,6 @@ k3_reset: reset-controller {
 	};
 
 	wkup_conf: bus at 43000000 {
-		bootph-all;
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -59,6 +57,8 @@ secure_proxy_sa3: mailbox at 43600000 {
 		reg = <0x00 0x43600000 0x00 0x10000>,
 		      <0x00 0x44880000 0x00 0x20000>,
 		      <0x00 0x44860000 0x00 0x20000>;
+		bootph-pre-ram;
+
 		/*
 		 * Marked Disabled:
 		 * Node is incomplete as it is meant for bootloaders and
@@ -172,13 +172,13 @@ mcu_timer0: timer at 40400000 {
 		assigned-clocks = <&k3_clks 35 2>;
 		assigned-clock-parents = <&k3_clks 35 3>;
 		power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+		bootph-all;
 		ti,timer-pwm;
 		/* Non-MPU Firmware usage */
 		status = "reserved";
 	};
 
 	mcu_timer1: timer at 40410000 {
-		bootph-all;
 		compatible = "ti,am654-timer";
 		reg = <0x00 0x40410000 0x00 0x400>;
 		interrupts = <GIC_SPI 817 IRQ_TYPE_LEVEL_HIGH>;
@@ -458,7 +458,6 @@ mcu_spi2: spi at 40320000 {
 	};
 
 	mcu_navss: bus at 28380000 {
-		bootph-all;
 		compatible = "simple-bus";
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -515,6 +514,8 @@ secure_proxy_mcu: mailbox at 2a480000 {
 		reg = <0x00 0x2a480000 0x00 0x80000>,
 		      <0x00 0x2a380000 0x00 0x80000>,
 		      <0x00 0x2a400000 0x00 0x80000>;
+		bootph-pre-ram;
+
 		/*
 		 * Marked Disabled:
 		 * Node is incomplete as it is meant for bootloaders and
@@ -632,6 +633,7 @@ wkup_vtm0: temperature-sensor at 42040000 {
 		      <0x00 0x42050000 0x00 0x350>;
 		power-domains = <&k3_pds 243 TI_SCI_PD_SHARED>;
 		#thermal-sensor-cells = <1>;
+		bootph-pre-ram;
 	};
 
 	tscadc0: tscadc at 40200000 {

-- 
2.46.0




More information about the linux-arm-kernel mailing list