[PATCH] tty: atmel_serial: use the correct RTS flag.

[Ilpo Järvinen]

On Tue, 13 Aug 2024, Alexander Dahl wrote:

> Hello Mathieu,
> 
> Am Thu, Aug 08, 2024 at 08:06:37AM +0200 schrieb Mathieu Othacehe:
> > In RS485 mode, the RTS pin is driven high by hardware when the transmitter
> > is operating. This behaviour cannot be changed. This means that the driver
> > should claim that it supports SER_RS485_RTS_ON_SEND and not
> > SER_RS485_RTS_AFTER_SEND.
> > 
> > Otherwise, when configuring the port with the SER_RS485_RTS_ON_SEND, one
> > get the following warning:
> > 
> > kern.warning kernel: atmel_usart_serial atmel_usart_serial.2.auto:
> > ttyS1 (1): invalid RTS setting, using RTS_AFTER_SEND instead
> 
> I've seen this warning already, when migrating a sam9x60 based board
> from LTS kernel 6.1 to 6.6, so thanks for taking care of this.
> 
> I can confirm after applying the patch on top of 6.6.44 the warning is
> gone, and RS-485 communication still works on our platform, so …
> 
> Tested-by: Alexander Dahl <ada at thorsis.com>
> 
> Does this deserve a Fixes tag for the change which introduced struct
> serial_rs485 to the atmel serial driver?  Then it should be this:
> 
> Fixes: af47c491e3c7 ("serial: atmel: Fill in rs485_supported")
> 
> Greets
> Alex
> 
> > which is contradictory with what's really happening.
> > 
> > Signed-off-by: Mathieu Othacehe <othacehe at gnu.org>

This got (more) broken by one of the changes made into 
uart_sanitize_serial_rs485() even if af47c491e3c7 used a wrong flag and 
must be fixed. The code in af47c491e3c7:uart_sanitize_serial_rs485() 
picks RTS_ON_SEND if no RTS_*_SEND flag is specified by the userspace 
code.

The behavior change was due to 4afeced55baa ("serial: core: fix sanitizing 
check for RTS settings") that enforced flags differently (4afeced55baa 
makes very much sense but because of the wrong flag in atmel driver, it 
ended up breaking atmel).

-- 
 i.

> > ---
> >  drivers/tty/serial/atmel_serial.c | 2 +-
> >  1 file changed, 1 insertion(+), 1 deletion(-)
> > 
> > diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> > index 0a90964d6d107..09b246c9e389e 100644
> > --- a/drivers/tty/serial/atmel_serial.c
> > +++ b/drivers/tty/serial/atmel_serial.c
> > @@ -2514,7 +2514,7 @@ static const struct uart_ops atmel_pops = {
> >  };
> >  
> >  static const struct serial_rs485 atmel_rs485_supported = {
> > -	.flags = SER_RS485_ENABLED | SER_RS485_RTS_AFTER_SEND | SER_RS485_RX_DURING_TX,
> > +	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RX_DURING_TX,
> >  	.delay_rts_before_send = 1,
> >  	.delay_rts_after_send = 1,
> >  };
> > -- 
> > 2.45.2
> > 
> > 
>