[PATCH v5 05/12] PCI: brcmstb: Use swinit reset if available

[Manivannan Sadhasivam]

On Mon, Aug 12, 2024 at 09:43:46AM -0400, Jim Quinlan wrote:
> On Fri, Aug 9, 2024 at 5:53 AM Stanimir Varbanov <svarbanov at suse.de> wrote:
> >
> > Hi Jim,
> >
> > On 8/1/24 01:28, Jim Quinlan wrote:
> > > The 7712 SOC adds a software init reset device for the PCIe HW.
> > > If found in the DT node, use it.
> > >
> > > Signed-off-by: Jim Quinlan <james.quinlan at broadcom.com>
> > > ---
> > >  drivers/pci/controller/pcie-brcmstb.c | 19 +++++++++++++++++++
> > >  1 file changed, 19 insertions(+)
> > >
> > > diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
> > > index 4d68fe318178..948fd4d176bc 100644
> > > --- a/drivers/pci/controller/pcie-brcmstb.c
> > > +++ b/drivers/pci/controller/pcie-brcmstb.c
> > > @@ -266,6 +266,7 @@ struct brcm_pcie {
> > >       struct reset_control    *rescal;
> > >       struct reset_control    *perst_reset;
> > >       struct reset_control    *bridge_reset;
> > > +     struct reset_control    *swinit_reset;
> > >       int                     num_memc;
> > >       u64                     memc_size[PCIE_BRCM_MAX_MEMC];
> > >       u32                     hw_rev;
> > > @@ -1633,12 +1634,30 @@ static int brcm_pcie_probe(struct platform_device *pdev)
> > >       if (IS_ERR(pcie->bridge_reset))
> > >               return PTR_ERR(pcie->bridge_reset);
> > >
> > > +     pcie->swinit_reset = devm_reset_control_get_optional_exclusive(&pdev->dev, "swinit");
> > > +     if (IS_ERR(pcie->swinit_reset))
> > > +             return PTR_ERR(pcie->swinit_reset);
> > > +
> > >       ret = clk_prepare_enable(pcie->clk);
> > >       if (ret)
> > >               return dev_err_probe(&pdev->dev, ret, "could not enable clock\n");
> > >
> > >       pcie->bridge_sw_init_set(pcie, 0);
> > >
> > > +     if (pcie->swinit_reset) {
> > > +             ret = reset_control_assert(pcie->swinit_reset);
> > > +             if (dev_err_probe(&pdev->dev, ret, "could not assert reset 'swinit'\n"))
> > > +                     goto clk_disable_unprepare;
> > > +
> > > +             /* HW team recommends 1us for proper sync and propagation of reset */
> > > +             udelay(1);
> >
> > Hmm, shouldn't this delay be part of .assert/.deassert reset_control
> > driver?  I think this detail is reset-control hw specific and the
> > consumers does not need to know it.
> 
> This was discussed previously.  I pointed out that we use a reset
> provider that governs dozens of devices.  The only thing that the
> provider could do is to employ a  worst case delay used for all
> resets.  This is unacceptable; we have certain devices that may have
> to invoke
> reset often and require timely action, and we do not want them having
> to wait the same amount of worst case delay as for example, a UART device reset.
> 
> Further, if I do a "grep reset_control_assert -A 10 drivers"  I see
> plenty of existing drivers that use usleep/msleep/udelay after the call to
> reset_control_assert, just as I am doing now.
> 
> As far as my opinion goes (FWIW) I think the delay is more apt to
> be present in the consumer driver and not the provider driver.  To
> ascertain this specific delay I had to consult with the PCIe HW team,
> not the HW team that implemented the reset controller.
> 

Yeah. Often the reset controller won't have any idea about the delay required
between assert + deassert, unless the reset controller is closely tied to the
peripheral. So keeping the delay in consumer drivers is the right thing to do.

- Mani

-- 
மணிவண்ணன் சதாசிவம்