[PATCH v2 3/4] arm64: dts: rockchip: Add base DT for rk3528 SoC

[Yao Zi]

On Sun, Aug 11, 2024 at 11:39:18PM +0200, Dragan Simic wrote:
> Hello Yao,
> 
> Please see one comment below.
> 
> On 2024-08-11 16:07, Yao Zi wrote:
> > This initial device tree describes CPU, interrupts and UART on the chip
> > and is able to boot into basic kernel with only UART. Cache information
> > is omitted for now as there is no precise documentation. Support for
> > other features will be added later.
> > 
> > Signed-off-by: Yao Zi <ziyao at disroot.org>
> > ---
> >  arch/arm64/boot/dts/rockchip/rk3528.dtsi | 182 +++++++++++++++++++++++
> >  1 file changed, 182 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/rockchip/rk3528.dtsi
> > 
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3528.dtsi
> > b/arch/arm64/boot/dts/rockchip/rk3528.dtsi
> > new file mode 100644
> > index 000000000000..0596cdc38737
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/rockchip/rk3528.dtsi
> > @@ -0,0 +1,182 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (c) 2022 Rockchip Electronics Co., Ltd.
> > + * Copyright (c) 2024 Yao Zi <ziyao at disroot.org>
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +
> > +/ {
> > +	compatible = "rockchip,rk3528";
> > +
> > +	interrupt-parent = <&gic>;
> > +	#address-cells = <2>;
> > +	#size-cells = <2>;
> > +
> > +	aliases {
> > +		serial0 = &uart0;
> > +		serial1 = &uart1;
> > +		serial2 = &uart2;
> > +		serial3 = &uart3;
> > +		serial4 = &uart4;
> > +		serial5 = &uart5;
> > +		serial6 = &uart6;
> > +		serial7 = &uart7;
> > +	};
> > +
> > +	cpus {
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +
> > +		cpu-map {
> > +			cluster0 {
> > +				core0 {
> > +					cpu = <&cpu0>;
> > +				};
> > +				core1 {
> > +					cpu = <&cpu1>;
> > +				};
> > +				core2 {
> > +					cpu = <&cpu2>;
> > +				};
> > +				core3 {
> > +					cpu = <&cpu3>;
> > +				};
> > +			};
> > +		};
> > +
> > +		cpu0: cpu at 0 {
> > +			compatible = "arm,cortex-a53";
> > +			reg = <0x0>;
> > +			device_type = "cpu";
> > +			enable-method = "psci";
> > +		};
> > +
> > +		cpu1: cpu at 1 {
> > +			compatible = "arm,cortex-a53";
> > +			reg = <0x1>;
> > +			device_type = "cpu";
> > +			enable-method = "psci";
> > +		};
> > +
> > +		cpu2: cpu at 2 {
> > +			compatible = "arm,cortex-a53";
> > +			reg = <0x2>;
> > +			device_type = "cpu";
> > +			enable-method = "psci";
> > +		};
> > +
> > +		cpu3: cpu at 3 {
> > +			compatible = "arm,cortex-a53";
> > +			reg = <0x3>;
> > +			device_type = "cpu";
> > +			enable-method = "psci";
> > +		};
> > +	};
> > +
> > +	psci {
> > +		compatible = "arm,psci-1.0", "arm,psci-0.2";
> > +		method = "smc";
> > +	};
> > +
> > +	timer {
> > +		compatible = "arm,armv8-timer";
> > +		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
> > IRQ_TYPE_LEVEL_LOW)>,
> > +			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> > +			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> > +			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> > +	};
> > +
> > +	xin24m: clk-24m {
> 
> Please use "xin24m: clock-xin24m { ... }" instead, because that follows
> the recently established revised pattern for clock names.  We should have
> come consistency in the new SoC dtsi additions.

It's a careless typo, sorry for the noise. Will be fixed in next version.

Best regards,
Yao Zi