[PATCH v3 5/5] arm64: dts: ti: k3-j7200*: Add bootph-* properties

[Kumar, Udit]

On 7/30/2024 3:23 PM, Manorit Chawdhry wrote:
> Adds bootph-* properties to the leaf nodes to enable U-boot to
> utilise them.
>
> Signed-off-by: Manorit Chawdhry <m-chawdhry at ti.com>
> ---
>   .../arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 20 ++++++++++++++++++++
>   arch/arm64/boot/dts/ti/k3-j7200-main.dtsi            |  2 ++
>   arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      | 10 ++++++++++
>   arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi          |  7 +++++++
>   4 files changed, 39 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index 6593c5da82c0..ec522595fc83 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> [..]
>   
>   
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> index 9386bf3ef9f6..b95656942412 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> @@ -136,6 +136,7 @@ secure_proxy_main: mailbox at 32c00000 {
>   			      <0x00 0x32800000 0x00 0x100000>;
>   			interrupt-names = "rx_011";
>   			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> +			bootph-all;
>   		};
>   
>   		hwspinlock: spinlock at 30e00000 {
> @@ -1528,5 +1529,6 @@ main_esm: esm at 700000 {
>   		compatible = "ti,j721e-esm";
>   		reg = <0x0 0x700000 0x0 0x1000>;
>   		ti,esm-pins = <656>, <657>;
> +		bootph-all;

Should be bootph-pre-ram

if you think otherwise then please update mcu_esm

>   	};
>   };
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
> index 5097d192c2b2..f8a5ad4737da 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
> @@ -21,16 +21,19 @@ dmsc: system-controller at 44083000 {
>   		k3_pds: power-controller {
>   			compatible = "ti,sci-pm-domain";
>   			#power-domain-cells = <2>;
> +			bootph-all;
>   		};
>   
>   		k3_clks: clock-controller {
>   			compatible = "ti,k2g-sci-clk";
>   			#clock-cells = <2>;
> +			bootph-all;
>   		};
>   
>   		k3_reset: reset-controller {
>   			compatible = "ti,sci-reset";
>   			#reset-cells = <2>;
> +			bootph-all;
>   		};
>   	};
>   
> @@ -45,6 +48,7 @@ mcu_timer0: timer at 40400000 {
>   		assigned-clock-parents = <&k3_clks 35 2>;
>   		power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
>   		ti,timer-pwm;
> +		bootph-pre-ram;

I see this node is marked as reserved

Do we plan to use in bootloader ?

>   	};
>   
>   	mcu_timer1: timer at 40410000 {
> @@ -191,6 +195,7 @@ wkup_conf: bus at 43000000 {
>   		chipid: chipid at 14 {
>   			compatible = "ti,am654-chipid";
>   			reg = <0x14 0x4>;
> [...]
> @@ -389,6 +396,7 @@ secure_proxy_mcu: mailbox at 2a480000 {
>   		 * firmware on non-MPU processors
>   		 */
>   		status = "disabled";
> +		bootph-pre-ram;
>   	};
>   
>   	mcu_cpsw: ethernet at 46000000 {
> @@ -534,6 +542,7 @@ hbmc_mux: mux-controller at 47000004 {
>   			reg = <0x00 0x47000004 0x00 0x4>;
>   			#mux-control-cells = <1>;
>   			mux-reg-masks = <0x0 0x2>; /* HBMC select */
> +			bootph-pre-ram;
>   		};
>   
>   		hbmc: hyperbus at 47034000 {

I think you should consider to mark hbmc node for boot phase as well


> @@ -652,6 +661,7 @@ wkup_vtm0: temperature-sensor at 42040000 {
>   		      <0x00 0x42050000 0x00 0x350>;
>   		power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
>   		#thermal-sensor-cells = <1>;
> +		bootph-pre-ram;
>   	};
>   
>   	mcu_esm: esm at 40800000 {
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> index 21fe194a5766..d78f86889bf9 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> @@ -121,6 +121,7 @@ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (B8) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */
>   			J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
>   			J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
>   		>;
> [..]
>   			bucka2: buck2 {
> @@ -464,6 +470,7 @@ flash at 0 {
>   		cdns,tchsh-ns = <60>;
>   		cdns,tslch-ns = <60>;
>   		cdns,read-delay = <4>;
> +		bootph-all;
>   
>   		partitions {
>   			compatible = "fixed-partitions";


Please consider, adding bootph in ospi0 node as well around 
"ospi.phypattern"


>