[PATCH v2 5/5] arm64: dts: imx95-19x19-evk: add typec nodes and enable usb3 node

[Xu Yang]

This board has one Type-C port which has USB3 capability. This will
add typec nodes and enable usb3 node.

Signed-off-by: Xu Yang <xu.yang_2 at nxp.com>

---
Changes in v2:
 - no changes
---
 .../boot/dts/freescale/imx95-19x19-evk.dts    | 81 +++++++++++++++++++
 1 file changed, 81 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
index d14a54ab4fd4..46a9cd3d4403 100644
--- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/usb/pd.h>
 #include "imx95.dtsi"
 
 / {
@@ -99,6 +100,48 @@ i2c7_pcal6524: i2c7-gpio at 22 {
 		interrupt-parent = <&gpio5>;
 		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
 	};
+
+	ptn5110: tcpc at 50 {
+		compatible = "nxp,ptn5110", "tcpci";
+		reg = <0x50>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_typec>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
+
+		typec_con: connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			data-role = "dual";
+			try-power-role = "sink";
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 0, PDO_FIXED_USB_COMM)>;
+			op-sink-microwatt = <0>;
+			self-powered;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port at 0 {
+					reg = <0>;
+
+					typec_con_hs: endpoint {
+						remote-endpoint = <&usb3_data_hs>;
+					};
+				};
+
+				port at 1 {
+					reg = <1>;
+
+					typec_con_ss: endpoint {
+						remote-endpoint = <&usb3_data_ss>;
+					};
+				};
+			};
+		};
+	};
 };
 
 &lpuart1 {
@@ -128,6 +171,38 @@ &pcie1 {
 	status = "okay";
 };
 
+&usb3 {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+
+	port {
+		usb3_data_ss: endpoint {
+			remote-endpoint = <&typec_con_ss>;
+		};
+	};
+};
+
+&usb3_dwc3 {
+	dr_mode = "otg";
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+	usb-role-switch;
+	role-switch-default-mode = "peripheral";
+	snps,dis-u1-entry-quirk;
+	snps,dis-u2-entry-quirk;
+	status = "okay";
+
+	port {
+		usb3_data_hs: endpoint {
+			remote-endpoint = <&typec_con_hs>;
+		};
+	};
+};
+
 &usdhc1 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
 	pinctrl-0 = <&pinctrl_usdhc1>;
@@ -245,6 +320,12 @@ IMX95_PAD_SD2_RESET_B__GPIO3_IO_BIT7		0x31e
 		>;
 	};
 
+	pinctrl_typec: typecgrp {
+		fsl,pins = <
+			IMX95_PAD_GPIO_IO34__GPIO5_IO_BIT14			0x31e
+		>;
+	};
+
 	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			IMX95_PAD_SD2_CD_B__GPIO3_IO_BIT0		0x31e
-- 
2.34.1