[PATCH 1/2] pinctrl: rockchip: Add rk3576 pinctrl support
Detlev Casanova
detlev.casanova at collabora.com
Fri Aug 2 07:52:03 PDT 2024
From: Steven Liu <steven.liu at rock-chips.com>
Add support for the 5 rk3576 GPIO banks.
This also adds support for optionnal support of the sys-grf syscon,
used for i3c software controlled weak pull-up.
Signed-off-by: Steven Liu <steven.liu at rock-chips.com>
[rebase, reword commit message]
Signed-off-by: Detlev Casanova <detlev.casanova at collabora.com>
---
drivers/pinctrl/pinctrl-rockchip.c | 228 +++++++++++++++++++++++++++++
drivers/pinctrl/pinctrl-rockchip.h | 2 +
2 files changed, 230 insertions(+)
diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
index 0eacaf10c640f..110ed81d650be 100644
--- a/drivers/pinctrl/pinctrl-rockchip.c
+++ b/drivers/pinctrl/pinctrl-rockchip.c
@@ -84,6 +84,27 @@
}, \
}
+#define PIN_BANK_IOMUX_FLAGS_OFFSET_PULL_FLAGS(id, pins, label, iom0, \
+ iom1, iom2, iom3, \
+ offset0, offset1, \
+ offset2, offset3, pull0, \
+ pull1, pull2, pull3) \
+ { \
+ .bank_num = id, \
+ .nr_pins = pins, \
+ .name = label, \
+ .iomux = { \
+ { .type = iom0, .offset = offset0 }, \
+ { .type = iom1, .offset = offset1 }, \
+ { .type = iom2, .offset = offset2 }, \
+ { .type = iom3, .offset = offset3 }, \
+ }, \
+ .pull_type[0] = pull0, \
+ .pull_type[1] = pull1, \
+ .pull_type[2] = pull2, \
+ .pull_type[3] = pull3, \
+ }
+
#define PIN_BANK_DRV_FLAGS(id, pins, label, type0, type1, type2, type3) \
{ \
.bank_num = id, \
@@ -1120,6 +1141,11 @@ static int rockchip_get_mux(struct rockchip_pin_bank *bank, int pin)
if (bank->recalced_mask & BIT(pin))
rockchip_get_recalced_mux(bank, pin, ®, &bit, &mask);
+ if (ctrl->type == RK3576) {
+ if ((bank->bank_num == 0) && (pin >= RK_PB4) && (pin <= RK_PB7))
+ reg += 0x1FF4; /* GPIO0_IOC_GPIO0B_IOMUX_SEL_H */
+ }
+
if (ctrl->type == RK3588) {
if (bank->bank_num == 0) {
if ((pin >= RK_PB4) && (pin <= RK_PD7)) {
@@ -1193,6 +1219,7 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
struct device *dev = info->dev;
int iomux_num = (pin / 8);
struct regmap *regmap;
+ struct regmap *regmap_sys;
int reg, ret, mask, mux_type;
u8 bit;
u32 data, rmask, route_location, route_reg, route_val;
@@ -1213,6 +1240,8 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
else
regmap = info->regmap_base;
+ regmap_sys = info->regmap_sys_grf;
+
/* get basic quadrupel of mux registers and the correct reg inside */
mux_type = bank->iomux[iomux_num].type;
reg = bank->iomux[iomux_num].offset;
@@ -1234,6 +1263,20 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
if (bank->recalced_mask & BIT(pin))
rockchip_get_recalced_mux(bank, pin, ®, &bit, &mask);
+ if (ctrl->type == RK3576) {
+ if ((bank->bank_num == 0) && (pin >= RK_PB4) && (pin <= RK_PB7))
+ reg += 0x1FF4; /* GPIO0_IOC_GPIO0B_IOMUX_SEL_H */
+ /* i3c0 weakpull controlled by software */
+ if (((bank->bank_num == 0) && (pin == RK_PC5) && (mux == 0xb)) ||
+ ((bank->bank_num == 1) && (pin == RK_PD1) && (mux == 0xa)))
+ regmap_update_bits(regmap_sys, 0x4, 0xc000c0, 0xc000c0);
+ /* i3c1 weakpull controlled by software */
+ if (((bank->bank_num == 2) && (pin == RK_PA5) && (mux == 0xe)) ||
+ ((bank->bank_num == 2) && (pin == RK_PD6) && (mux == 0xc)) ||
+ ((bank->bank_num == 3) && (pin == RK_PD1) && (mux == 0xb)))
+ regmap_update_bits(regmap_sys, 0x4, 0x3000300, 0x3000300);
+ }
+
if (ctrl->type == RK3588) {
if (bank->bank_num == 0) {
if ((pin >= RK_PB4) && (pin <= RK_PD7)) {
@@ -2038,6 +2081,142 @@ static int rk3568_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
return 0;
}
+#define RK3576_DRV_BITS_PER_PIN 4
+#define RK3576_DRV_PINS_PER_REG 4
+#define RK3576_DRV_GPIO0_AL_OFFSET 0x10
+#define RK3576_DRV_GPIO0_BH_OFFSET 0x2014
+#define RK3576_DRV_GPIO1_OFFSET 0x6020
+#define RK3576_DRV_GPIO2_OFFSET 0x6040
+#define RK3576_DRV_GPIO3_OFFSET 0x6060
+#define RK3576_DRV_GPIO4_AL_OFFSET 0x6080
+#define RK3576_DRV_GPIO4_CL_OFFSET 0xA090
+#define RK3576_DRV_GPIO4_DL_OFFSET 0xB098
+
+static int rk3576_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+ int pin_num, struct regmap **regmap,
+ int *reg, u8 *bit)
+{
+ struct rockchip_pinctrl *info = bank->drvdata;
+
+ *regmap = info->regmap_base;
+
+ if (bank->bank_num == 0 && pin_num < 12)
+ *reg = RK3576_DRV_GPIO0_AL_OFFSET;
+ else if (bank->bank_num == 0)
+ *reg = RK3576_DRV_GPIO0_BH_OFFSET - 0xc;
+ else if (bank->bank_num == 1)
+ *reg = RK3576_DRV_GPIO1_OFFSET;
+ else if (bank->bank_num == 2)
+ *reg = RK3576_DRV_GPIO2_OFFSET;
+ else if (bank->bank_num == 3)
+ *reg = RK3576_DRV_GPIO3_OFFSET;
+ else if (bank->bank_num == 4 && pin_num < 16)
+ *reg = RK3576_DRV_GPIO4_AL_OFFSET;
+ else if (bank->bank_num == 4 && pin_num < 24)
+ *reg = RK3576_DRV_GPIO4_CL_OFFSET - 0x10;
+ else if (bank->bank_num == 4)
+ *reg = RK3576_DRV_GPIO4_DL_OFFSET - 0x18;
+ else
+ dev_err(info->dev, "unsupported bank_num %d\n", bank->bank_num);
+
+ *reg += ((pin_num / RK3576_DRV_PINS_PER_REG) * 4);
+ *bit = pin_num % RK3576_DRV_PINS_PER_REG;
+ *bit *= RK3576_DRV_BITS_PER_PIN;
+
+ return 0;
+}
+
+#define RK3576_PULL_BITS_PER_PIN 2
+#define RK3576_PULL_PINS_PER_REG 8
+#define RK3576_PULL_GPIO0_AL_OFFSET 0x20
+#define RK3576_PULL_GPIO0_BH_OFFSET 0x2028
+#define RK3576_PULL_GPIO1_OFFSET 0x6110
+#define RK3576_PULL_GPIO2_OFFSET 0x6120
+#define RK3576_PULL_GPIO3_OFFSET 0x6130
+#define RK3576_PULL_GPIO4_AL_OFFSET 0x6140
+#define RK3576_PULL_GPIO4_CL_OFFSET 0xA148
+#define RK3576_PULL_GPIO4_DL_OFFSET 0xB14C
+
+static int rk3576_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+ int pin_num, struct regmap **regmap,
+ int *reg, u8 *bit)
+{
+ struct rockchip_pinctrl *info = bank->drvdata;
+
+ *regmap = info->regmap_base;
+
+ if (bank->bank_num == 0 && pin_num < 12)
+ *reg = RK3576_PULL_GPIO0_AL_OFFSET;
+ else if (bank->bank_num == 0)
+ *reg = RK3576_PULL_GPIO0_BH_OFFSET - 0x4;
+ else if (bank->bank_num == 1)
+ *reg = RK3576_PULL_GPIO1_OFFSET;
+ else if (bank->bank_num == 2)
+ *reg = RK3576_PULL_GPIO2_OFFSET;
+ else if (bank->bank_num == 3)
+ *reg = RK3576_PULL_GPIO3_OFFSET;
+ else if (bank->bank_num == 4 && pin_num < 16)
+ *reg = RK3576_PULL_GPIO4_AL_OFFSET;
+ else if (bank->bank_num == 4 && pin_num < 24)
+ *reg = RK3576_PULL_GPIO4_CL_OFFSET - 0x8;
+ else if (bank->bank_num == 4)
+ *reg = RK3576_PULL_GPIO4_DL_OFFSET - 0xc;
+ else
+ dev_err(info->dev, "unsupported bank_num %d\n", bank->bank_num);
+
+ *reg += ((pin_num / RK3576_PULL_PINS_PER_REG) * 4);
+ *bit = pin_num % RK3576_PULL_PINS_PER_REG;
+ *bit *= RK3576_PULL_BITS_PER_PIN;
+
+ return 0;
+}
+
+#define RK3576_SMT_BITS_PER_PIN 1
+#define RK3576_SMT_PINS_PER_REG 8
+#define RK3576_SMT_GPIO0_AL_OFFSET 0x30
+#define RK3576_SMT_GPIO0_BH_OFFSET 0x2040
+#define RK3576_SMT_GPIO1_OFFSET 0x6210
+#define RK3576_SMT_GPIO2_OFFSET 0x6220
+#define RK3576_SMT_GPIO3_OFFSET 0x6230
+#define RK3576_SMT_GPIO4_AL_OFFSET 0x6240
+#define RK3576_SMT_GPIO4_CL_OFFSET 0xA248
+#define RK3576_SMT_GPIO4_DL_OFFSET 0xB24C
+
+static int rk3576_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
+ int pin_num,
+ struct regmap **regmap,
+ int *reg, u8 *bit)
+{
+ struct rockchip_pinctrl *info = bank->drvdata;
+
+ *regmap = info->regmap_base;
+
+ if (bank->bank_num == 0 && pin_num < 12)
+ *reg = RK3576_SMT_GPIO0_AL_OFFSET;
+ else if (bank->bank_num == 0)
+ *reg = RK3576_SMT_GPIO0_BH_OFFSET - 0x4;
+ else if (bank->bank_num == 1)
+ *reg = RK3576_SMT_GPIO1_OFFSET;
+ else if (bank->bank_num == 2)
+ *reg = RK3576_SMT_GPIO2_OFFSET;
+ else if (bank->bank_num == 3)
+ *reg = RK3576_SMT_GPIO3_OFFSET;
+ else if (bank->bank_num == 4 && pin_num < 16)
+ *reg = RK3576_SMT_GPIO4_AL_OFFSET;
+ else if (bank->bank_num == 4 && pin_num < 24)
+ *reg = RK3576_SMT_GPIO4_CL_OFFSET - 0x8;
+ else if (bank->bank_num == 4)
+ *reg = RK3576_SMT_GPIO4_DL_OFFSET - 0xc;
+ else
+ dev_err(info->dev, "unsupported bank_num %d\n", bank->bank_num);
+
+ *reg += ((pin_num / RK3576_SMT_PINS_PER_REG) * 4);
+ *bit = pin_num % RK3576_SMT_PINS_PER_REG;
+ *bit *= RK3576_SMT_BITS_PER_PIN;
+
+ return 0;
+}
+
#define RK3588_PMU1_IOC_REG (0x0000)
#define RK3588_PMU2_IOC_REG (0x4000)
#define RK3588_BUS_IOC_REG (0x8000)
@@ -2332,6 +2511,10 @@ static int rockchip_set_drive_perpin(struct rockchip_pin_bank *bank,
rmask_bits = RK3568_DRV_BITS_PER_PIN;
ret = (1 << (strength + 1)) - 1;
goto config;
+ } else if (ctrl->type == RK3576) {
+ rmask_bits = RK3576_DRV_BITS_PER_PIN;
+ ret = ((strength & BIT(2)) >> 2) | ((strength & BIT(0)) << 2) | (strength & BIT(1));
+ goto config;
}
if (ctrl->type == RV1126) {
@@ -2469,6 +2652,7 @@ static int rockchip_get_pull(struct rockchip_pin_bank *bank, int pin_num)
case RK3368:
case RK3399:
case RK3568:
+ case RK3576:
case RK3588:
pull_type = bank->pull_type[pin_num / 8];
data >>= bit;
@@ -2528,6 +2712,7 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
case RK3368:
case RK3399:
case RK3568:
+ case RK3576:
case RK3588:
pull_type = bank->pull_type[pin_num / 8];
ret = -EINVAL;
@@ -2793,6 +2978,7 @@ static bool rockchip_pinconf_pull_valid(struct rockchip_pin_ctrl *ctrl,
case RK3368:
case RK3399:
case RK3568:
+ case RK3576:
case RK3588:
return (pull != PIN_CONFIG_BIAS_PULL_PIN_DEFAULT);
}
@@ -3439,6 +3625,15 @@ static int rockchip_pinctrl_probe(struct platform_device *pdev)
}
}
+ /* try to find the optional reference to the sys_grf syscon */
+ node = of_parse_phandle(np, "rockchip,sys-grf", 0);
+ if (node) {
+ info->regmap_sys_grf = syscon_node_to_regmap(node);
+ of_node_put(node);
+ if (IS_ERR(info->regmap_sys_grf))
+ return PTR_ERR(info->regmap_sys_grf);
+ }
+
/* try to find the optional reference to the pmu syscon */
node = of_parse_phandle(np, "rockchip,pmu", 0);
if (node) {
@@ -3949,6 +4144,37 @@ static struct rockchip_pin_ctrl rk3568_pin_ctrl = {
.schmitt_calc_reg = rk3568_calc_schmitt_reg_and_bit,
};
+#define RK3576_PIN_BANK(ID, LABEL, OFFSET0, OFFSET1, OFFSET2, OFFSET3) \
+ PIN_BANK_IOMUX_FLAGS_OFFSET_PULL_FLAGS(ID, 32, LABEL, \
+ IOMUX_WIDTH_4BIT, \
+ IOMUX_WIDTH_4BIT, \
+ IOMUX_WIDTH_4BIT, \
+ IOMUX_WIDTH_4BIT, \
+ OFFSET0, OFFSET1, \
+ OFFSET2, OFFSET3, \
+ PULL_TYPE_IO_1V8_ONLY, \
+ PULL_TYPE_IO_1V8_ONLY, \
+ PULL_TYPE_IO_1V8_ONLY, \
+ PULL_TYPE_IO_1V8_ONLY)
+
+static struct rockchip_pin_bank rk3576_pin_banks[] = {
+ RK3576_PIN_BANK(0, "gpio0", 0, 0x8, 0x2004, 0x200C),
+ RK3576_PIN_BANK(1, "gpio1", 0x4020, 0x4028, 0x4030, 0x4038),
+ RK3576_PIN_BANK(2, "gpio2", 0x4040, 0x4048, 0x4050, 0x4058),
+ RK3576_PIN_BANK(3, "gpio3", 0x4060, 0x4068, 0x4070, 0x4078),
+ RK3576_PIN_BANK(4, "gpio4", 0x4080, 0x4088, 0xA390, 0xB398),
+};
+
+static struct rockchip_pin_ctrl rk3576_pin_ctrl __maybe_unused = {
+ .pin_banks = rk3576_pin_banks,
+ .nr_banks = ARRAY_SIZE(rk3576_pin_banks),
+ .label = "RK3576-GPIO",
+ .type = RK3576,
+ .pull_calc_reg = rk3576_calc_pull_reg_and_bit,
+ .drv_calc_reg = rk3576_calc_drv_reg_and_bit,
+ .schmitt_calc_reg = rk3576_calc_schmitt_reg_and_bit,
+};
+
static struct rockchip_pin_bank rk3588_pin_banks[] = {
RK3588_PIN_BANK_FLAGS(0, 32, "gpio0",
IOMUX_WIDTH_4BIT, PULL_TYPE_IO_1V8_ONLY),
@@ -4005,6 +4231,8 @@ static const struct of_device_id rockchip_pinctrl_dt_match[] = {
.data = &rk3399_pin_ctrl },
{ .compatible = "rockchip,rk3568-pinctrl",
.data = &rk3568_pin_ctrl },
+ { .compatible = "rockchip,rk3576-pinctrl",
+ .data = &rk3576_pin_ctrl },
{ .compatible = "rockchip,rk3588-pinctrl",
.data = &rk3588_pin_ctrl },
{},
diff --git a/drivers/pinctrl/pinctrl-rockchip.h b/drivers/pinctrl/pinctrl-rockchip.h
index 849266f8b1913..0b2b56014b173 100644
--- a/drivers/pinctrl/pinctrl-rockchip.h
+++ b/drivers/pinctrl/pinctrl-rockchip.h
@@ -197,6 +197,7 @@ enum rockchip_pinctrl_type {
RK3368,
RK3399,
RK3568,
+ RK3576,
RK3588,
};
@@ -455,6 +456,7 @@ struct rockchip_pinctrl {
int reg_size;
struct regmap *regmap_pull;
struct regmap *regmap_pmu;
+ struct regmap *regmap_sys_grf;
struct device *dev;
struct rockchip_pin_ctrl *ctrl;
struct pinctrl_desc pctl;
--
2.46.0
More information about the linux-arm-kernel
mailing list