[PATCH v3 3/3] phy: freescale: imx8qm-hsio: Add i.MX8QM HSIO PHY driver support
Rob Herring
robh at kernel.org
Wed Apr 24 14:50:39 PDT 2024
On Wed, Apr 24, 2024 at 02:21:23PM +0800, Richard Zhu wrote:
> Add i.MX8QM HSIO PHY driver support.
>
> Signed-off-by: Richard Zhu <hongxing.zhu at nxp.com>
> ---
> drivers/phy/freescale/Kconfig | 8 +
> drivers/phy/freescale/Makefile | 1 +
> drivers/phy/freescale/phy-fsl-imx8qm-hsio.c | 607 ++++++++++++++++++++
> 3 files changed, 616 insertions(+)
> create mode 100644 drivers/phy/freescale/phy-fsl-imx8qm-hsio.c
>
> diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
> index 853958fb2c06..c9ee48aeea9e 100644
> --- a/drivers/phy/freescale/Kconfig
> +++ b/drivers/phy/freescale/Kconfig
> @@ -35,6 +35,14 @@ config PHY_FSL_IMX8M_PCIE
> Enable this to add support for the PCIE PHY as found on
> i.MX8M family of SOCs.
>
> +config PHY_FSL_IMX8QM_HSIO
> + tristate "Freescale i.MX8QM HSIO PHY"
> + depends on OF && HAS_IOMEM
> + select GENERIC_PHY
> + help
> + Enable this to add support for the HSIO PHY as found on
> + i.MX8QM family of SOCs.
> +
> endif
>
> config PHY_FSL_LYNX_28G
> diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile
> index cedb328bc4d2..b56b4d5c18ea 100644
> --- a/drivers/phy/freescale/Makefile
> +++ b/drivers/phy/freescale/Makefile
> @@ -3,4 +3,5 @@ obj-$(CONFIG_PHY_FSL_IMX8MQ_USB) += phy-fsl-imx8mq-usb.o
> obj-$(CONFIG_PHY_MIXEL_LVDS_PHY) += phy-fsl-imx8qm-lvds-phy.o
> obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) += phy-fsl-imx8-mipi-dphy.o
> obj-$(CONFIG_PHY_FSL_IMX8M_PCIE) += phy-fsl-imx8m-pcie.o
> +obj-$(CONFIG_PHY_FSL_IMX8QM_HSIO) += phy-fsl-imx8qm-hsio.o
> obj-$(CONFIG_PHY_FSL_LYNX_28G) += phy-fsl-lynx-28g.o
> diff --git a/drivers/phy/freescale/phy-fsl-imx8qm-hsio.c b/drivers/phy/freescale/phy-fsl-imx8qm-hsio.c
> new file mode 100644
> index 000000000000..b3e17163e859
> --- /dev/null
> +++ b/drivers/phy/freescale/phy-fsl-imx8qm-hsio.c
> @@ -0,0 +1,607 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2024 NXP
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/of_device.h>
Check that you are including the right DT includes.
> +#include <linux/pci_regs.h>
> +#include <linux/phy/phy.h>
> +#include <linux/phy/pcie.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/phy/phy-imx8-pcie.h>
> +
> +#define MAX_NUM_PHY_MIXS 4
> +#define PHY_MIX_MAX_NUM_LANES 2
> +#define LANE_NUM_CLKS 5
> +
> +/* Parameters for the waiting for PCIe PHY PLL to lock */
> +#define PHY_INIT_WAIT_USLEEP_MAX 10
> +#define PHY_INIT_WAIT_TIMEOUT (1000 * PHY_INIT_WAIT_USLEEP_MAX)
> +
> +/* i.MX8Q HSIO registers */
> +#define HSIO_CTRL0 0x0
> +#define HSIO_APB_RSTN_0 BIT(0)
> +#define HSIO_APB_RSTN_1 BIT(1)
> +#define HSIO_PIPE_RSTN_0_MASK GENMASK(25, 24)
> +#define HSIO_PIPE_RSTN_1_MASK GENMASK(27, 26)
> +#define HSIO_MODE_MASK GENMASK(20, 17)
> +#define HSIO_MODE_PCIE 0x0
> +#define HSIO_MODE_SATA 0x4
> +#define HSIO_DEVICE_TYPE_MASK GENMASK(27, 24)
> +#define HSIO_EPCS_TXDEEMP BIT(5)
> +#define HSIO_EPCS_TXDEEMP_SEL BIT(6)
> +#define HSIO_EPCS_PHYRESET_N BIT(7)
> +#define HSIO_RESET_N BIT(12)
> +
> +#define HSIO_IOB_RXENA BIT(0)
> +#define HSIO_IOB_TXENA BIT(1)
> +#define HSIO_IOB_A_0_TXOE BIT(2)
> +#define HSIO_IOB_A_0_M1M0_2 BIT(4)
> +#define HSIO_IOB_A_0_M1M0_MASK GENMASK(4, 3)
> +#define HSIO_PHYX1_EPCS_SEL BIT(12)
> +#define HSIO_PCIE_AB_SELECT BIT(13)
> +
> +#define HSIO_PHY_STS0 0x4
> +#define HSIO_LANE0_TX_PLL_LOCK BIT(4)
> +#define HSIO_LANE1_TX_PLL_LOCK BIT(12)
> +
> +#define HSIO_CTRL2 0x8
> +#define HSIO_LTSSM_ENABLE BIT(4)
> +#define HSIO_BUTTON_RST_N BIT(21)
> +#define HSIO_PERST_N BIT(22)
> +#define HSIO_POWER_UP_RST_N BIT(23)
> +
> +#define HSIO_PCIE_STS0 0xc
> +#define HSIO_PM_REQ_CORE_RST BIT(19)
> +
> +#define HSIO_REG48_PMA_STATUS 0x30
> +#define HSIO_REG48_PMA_RDY BIT(7)
> +
> +/*
> + * There are three lanes PHY in i.MX8QM HSIO, and can be made up the
> + * following PHY modes in different use cases.
> + * +------------------------------------+
> + * | index | LAN0 | LAN1 | LAN2 |
> + * |------------------------------------|
> + * | 0 | PCIEA | | |
> + * |------------------------------------|
> + * | 1 | | PCIEB | |
> + * |------------------------------------|
> + * | 2 | PCIEA | PCIEA | |
> + * |------------------------------------|
> + * | 3 | | | PCIEB/SATA |
> + * +------------------------------------+
> + */
> +enum phy_mode_index {
> + IMX8Q_HSIO_LANE0_PCIE_PHY,
> + IMX8Q_HSIO_LANE1_PCIE_PHY,
> + IMX8Q_HSIO_LANE0_1_PCIE_PHY,
> + IMX8Q_HSIO_LANE2_PHY
> +};
> +
> +struct imx_hsio_drvdata {
> + int phy_mix_num;
> +};
> +
> +struct imx_hsio_phy_lane {
> + const char * const *clk_names;
> + struct clk_bulk_data clks[LANE_NUM_CLKS];
> +};
> +
> +struct imx_hsio_phy_mix {
> + u32 ctrl_index;
> + u32 ctrl_off;
> + u32 phy_off;
> + u32 phy_type;
> + struct imx_hsio_phy_lane lane[PHY_MIX_MAX_NUM_LANES];
> + struct imx_hsio_priv *priv;
> + struct phy *phy;
> + enum phy_mode pmix_mode;
> + enum phy_mode_index idx;
> +};
> +
> +struct imx_hsio_priv {
> + void __iomem *base;
> + struct device *dev;
> + u32 refclk_pad;
> + u32 hsio_cfg;
> + struct regmap *phy;
> + struct regmap *ctrl;
> + struct regmap *misc;
> + const struct imx_hsio_drvdata *drvdata;
> + struct imx_hsio_phy_mix pmix[MAX_NUM_PHY_MIXS];
> +};
> +
> +static const char * const lan0_pcie_clks[] = {"apb_pclk0", "pclk0", "ctl0_crr",
> + "phy0_crr", "misc_crr"};
> +static const char * const lan1_pciea_clks[] = {"apb_pclk1", "pclk1", "ctl0_crr",
> + "phy0_crr", "misc_crr"};
> +static const char * const lan1_pcieb_clks[] = {"apb_pclk1", "pclk1", "ctl1_crr",
> + "phy0_crr", "misc_crr"};
> +static const char * const lan2_pcieb_clks[] = {"apb_pclk2", "pclk2", "ctl1_crr",
> + "phy1_crr", "misc_crr"};
> +static const char * const lan2_sata_clks[] = {"pclk2", "epcs_tx", "epcs_rx",
> + "phy1_crr", "misc_crr"};
> +
> +static const struct regmap_config regmap_config = {
> + .reg_bits = 32,
> + .val_bits = 32,
> + .reg_stride = 4,
> +};
> +
> +static int imx_hsio_get_idx(int phy_type, int ctrl_index, int lane_mask)
> +{
> + int index;
> +
> + switch (phy_type) {
> + case PHY_TYPE_PCIE:
> + if (ctrl_index) { /* PCIEB */
> + if (lane_mask == IMX8Q_HSIO_LANE0) /* i.MX8QXP */
> + index = IMX8Q_HSIO_LANE0_PCIE_PHY;
> + else if (lane_mask == IMX8Q_HSIO_LANE1) /* i.MX8QM */
> + index = IMX8Q_HSIO_LANE1_PCIE_PHY;
> + else if (lane_mask == IMX8Q_HSIO_LANE2) /* i.MX8QM */
> + index = IMX8Q_HSIO_LANE2_PHY;
> + else
> + return -EINVAL;
> + } else { /* PCIEA */
> + if (lane_mask == (IMX8Q_HSIO_LANE0 | IMX8Q_HSIO_LANE1))
> + index = IMX8Q_HSIO_LANE0_1_PCIE_PHY;
> + else if (lane_mask == IMX8Q_HSIO_LANE0)
> + index = IMX8Q_HSIO_LANE0_PCIE_PHY;
> + else
> + return -EINVAL;
> + }
> + break;
> + case PHY_TYPE_SATA:
> + index = IMX8Q_HSIO_LANE2_PHY;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return index;
> +}
> +
> +static int imx_hsio_init(struct phy *phy)
> +{
> + int ret, i;
> + struct imx_hsio_phy_mix *pmix = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = pmix->priv;
> + struct device *dev = priv->dev;
> +
> + /* Assign clocks refer to different modes */
> + switch (pmix->phy_type) {
> + case PHY_TYPE_PCIE:
> + if (pmix->ctrl_index == 0) { /* PCIEA */
> + pmix->pmix_mode = PHY_MODE_PCIE;
> + pmix->ctrl_off = 0;
> + pmix->phy_off = 0;
> +
> + for (i = 0; i < LANE_NUM_CLKS; i++) {
> + if (pmix->idx == IMX8Q_HSIO_LANE0_PCIE_PHY) {
> + pmix->lane[0].clks[i].id = lan0_pcie_clks[i];
> + } else { /* 2 lanes are bound to PCIEA */
> + pmix->lane[0].clks[i].id = lan0_pcie_clks[i];
> + pmix->lane[1].clks[i].id = lan1_pciea_clks[i];
> + }
> + }
> + } else { /* PCIEB */
> + pmix->pmix_mode = PHY_MODE_PCIE;
> + if (pmix->idx == IMX8Q_HSIO_LANE0_PCIE_PHY) {
> + /* i.MX8QXP */
> + pmix->ctrl_off = 0;
> + pmix->phy_off = 0;
> + } else {
> + /*
> + * On i.MX8QM, only second or third lane can be
> + * bound to PCIEB.
> + */
> + pmix->ctrl_off = SZ_64K;
> + if (pmix->idx == IMX8Q_HSIO_LANE1_PCIE_PHY)
> + pmix->phy_off = 0;
> + else /* the third lane is bound to PCIEB */
> + pmix->phy_off = SZ_64K;
> + }
> +
> + for (i = 0; i < LANE_NUM_CLKS; i++) {
> + if (pmix->idx == IMX8Q_HSIO_LANE1_PCIE_PHY)
> + pmix->lane[0].clks[i].id = lan1_pcieb_clks[i];
> + else if (pmix->idx == IMX8Q_HSIO_LANE2_PHY)
> + pmix->lane[0].clks[i].id = lan2_pcieb_clks[i];
> + else /* i.MX8QXP only has PCIEB, idx is 0 */
> + pmix->lane[0].clks[i].id = lan0_pcie_clks[i];
> + }
> + }
> + break;
> + case PHY_TYPE_SATA:
> + /* On i.MX8QM, only the third lane can be bound to SATA */
> + pmix->ctrl_off = SZ_128K;
> + pmix->pmix_mode = PHY_MODE_SATA;
> + pmix->phy_off = SZ_64K;
> +
> + for (i = 0; i < LANE_NUM_CLKS; i++)
> + pmix->lane[0].clks[i].id = lan2_sata_clks[i];
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + /* Fetch clocks and enable them */
> + ret = devm_clk_bulk_get(dev, LANE_NUM_CLKS, pmix->lane[0].clks);
> + if (ret)
> + return ret;
> + if (pmix->idx == IMX8Q_HSIO_LANE0_1_PCIE_PHY) {
> + ret = devm_clk_bulk_get(dev, LANE_NUM_CLKS, pmix->lane[1].clks);
> + if (ret)
> + return ret;
> + }
> + ret = clk_bulk_prepare_enable(LANE_NUM_CLKS, pmix->lane[0].clks);
> + if (ret)
> + return ret;
> + if (pmix->idx == IMX8Q_HSIO_LANE0_1_PCIE_PHY) {
> + /* Enable the second lane's clocks */
> + ret = clk_bulk_prepare_enable(LANE_NUM_CLKS,
> + pmix->lane[1].clks);
> + if (ret) {
> + clk_bulk_disable_unprepare(LANE_NUM_CLKS,
> + pmix->lane[0].clks);
> + return ret;
> + }
> + }
> +
> + /* allow the clocks to stabilize */
> + usleep_range(200, 500);
> + return 0;
> +}
> +
> +static int imx_hsio_exit(struct phy *phy)
> +{
> + struct imx_hsio_phy_mix *pmix = phy_get_drvdata(phy);
> +
> + clk_bulk_disable_unprepare(LANE_NUM_CLKS, pmix->lane[0].clks);
> + if (pmix->idx == IMX8Q_HSIO_LANE0_1_PCIE_PHY)
> + /* Disable the clocks used by sencond lane of the PHY */
> + clk_bulk_disable_unprepare(LANE_NUM_CLKS, pmix->lane[1].clks);
> +
> + return 0;
> +}
> +
> +static void imx_hsio_pcie_phy_resets(struct phy *phy)
> +{
> + struct imx_hsio_phy_mix *pmix = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = pmix->priv;
> +
> + regmap_clear_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL2,
> + HSIO_BUTTON_RST_N);
> + regmap_clear_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL2,
> + HSIO_PERST_N);
> + regmap_clear_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL2,
> + HSIO_POWER_UP_RST_N);
> + regmap_set_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL2,
> + HSIO_BUTTON_RST_N);
> + regmap_set_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL2,
> + HSIO_PERST_N);
> + regmap_set_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL2,
> + HSIO_POWER_UP_RST_N);
> +
> + if (pmix->idx == IMX8Q_HSIO_LANE0_1_PCIE_PHY) {
> + regmap_set_bits(priv->phy, pmix->phy_off + HSIO_CTRL0,
> + HSIO_APB_RSTN_0);
> + regmap_set_bits(priv->phy, pmix->phy_off + HSIO_CTRL0,
> + HSIO_PIPE_RSTN_0_MASK);
> + regmap_set_bits(priv->phy, pmix->phy_off + HSIO_CTRL0,
> + HSIO_APB_RSTN_1);
> + regmap_set_bits(priv->phy, pmix->phy_off + HSIO_CTRL0,
> + HSIO_PIPE_RSTN_1_MASK);
> + } else if (pmix->idx == IMX8Q_HSIO_LANE1_PCIE_PHY) {
> + /* The second pmix */
> + regmap_set_bits(priv->phy, pmix->phy_off + HSIO_CTRL0,
> + HSIO_APB_RSTN_1);
> + regmap_set_bits(priv->phy, pmix->phy_off + HSIO_CTRL0,
> + HSIO_PIPE_RSTN_1_MASK);
> + } else {
> + regmap_set_bits(priv->phy, pmix->phy_off + HSIO_CTRL0,
> + HSIO_APB_RSTN_0);
> + regmap_set_bits(priv->phy, pmix->phy_off + HSIO_CTRL0,
> + HSIO_PIPE_RSTN_0_MASK);
> + }
> +}
> +
> +static void imx_hsio_sata_phy_resets(struct phy *phy)
> +{
> + struct imx_hsio_phy_mix *pmix = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = pmix->priv;
> +
> + /* clear PHY RST, then set it */
> + regmap_clear_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL0,
> + HSIO_EPCS_PHYRESET_N);
> + regmap_set_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL0,
> + HSIO_EPCS_PHYRESET_N);
> +
> + /* CTRL RST: SET -> delay 1 us -> CLEAR -> SET */
> + regmap_set_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL0, HSIO_RESET_N);
> + udelay(1);
> + regmap_clear_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL0,
> + HSIO_RESET_N);
> + regmap_set_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL0, HSIO_RESET_N);
> +}
> +
> +static void imx_hsio_configure_clk_pad(struct phy *phy)
> +{
> + bool pll = false;
> + u32 pad_mode;
> + struct imx_hsio_phy_mix *pmix = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = pmix->priv;
> +
> + pad_mode = priv->refclk_pad;
> + if (pad_mode == IMX8_PCIE_REFCLK_PAD_OUTPUT) {
> + pll = true;
> + regmap_update_bits(priv->misc, HSIO_CTRL0,
> + HSIO_IOB_A_0_TXOE | HSIO_IOB_A_0_M1M0_MASK,
> + HSIO_IOB_A_0_TXOE | HSIO_IOB_A_0_M1M0_2);
> + }
> +
> + regmap_update_bits(priv->misc, HSIO_CTRL0, HSIO_IOB_RXENA,
> + pll ? 0 : HSIO_IOB_RXENA);
> + regmap_update_bits(priv->misc, HSIO_CTRL0, HSIO_IOB_TXENA,
> + pll ? HSIO_IOB_TXENA : 0);
> +}
> +
> +static int imx_hsio_power_on(struct phy *phy)
> +{
> + int ret;
> + u32 val, addr, cond;
> + struct imx_hsio_phy_mix *pmix = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = pmix->priv;
> +
> + if (pmix->pmix_mode == PHY_MODE_PCIE)
> + imx_hsio_pcie_phy_resets(phy);
> + else /* SATA */
> + regmap_set_bits(priv->phy, pmix->phy_off + HSIO_CTRL0,
> + HSIO_APB_RSTN_0);
> +
> + if (priv->hsio_cfg & IMX8Q_HSIO_CFG_PCIEAX2PCIEB)
Can't this just be based on lane==2 and mode==pcie?
> + regmap_set_bits(priv->misc, HSIO_CTRL0, HSIO_PCIE_AB_SELECT);
> + if (priv->hsio_cfg & IMX8Q_HSIO_CFG_PCIEAX2SATA)
And this on mode==sata?
> + regmap_set_bits(priv->misc, HSIO_CTRL0, HSIO_PHYX1_EPCS_SEL);
> +
> + imx_hsio_configure_clk_pad(phy);
power_on is called per phy, but this appears to be some global state.
> +
> + if (pmix->pmix_mode == PHY_MODE_SATA) {
> + regmap_set_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL0,
> + HSIO_EPCS_TXDEEMP);
> + regmap_set_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL0,
> + HSIO_EPCS_TXDEEMP_SEL);
> +
> + imx_hsio_sata_phy_resets(phy);
> + } else {
> + /* Toggle apb_pclk to make sure PM_REQ_CORE_RST is cleared. */
> + clk_disable_unprepare(pmix->lane[0].clks[0].clk);
> + mdelay(1);
> + ret = clk_prepare_enable(pmix->lane[0].clks[0].clk);
> + if (ret) {
> + dev_err(priv->dev, "unable to enable phy apb_pclk\n");
> + return ret;
> + }
> +
> + addr = pmix->ctrl_off + HSIO_PCIE_STS0;
> + cond = HSIO_PM_REQ_CORE_RST;
> + ret = regmap_read_poll_timeout(priv->ctrl, addr, val,
> + (val & cond) == 0,
> + PHY_INIT_WAIT_USLEEP_MAX,
> + PHY_INIT_WAIT_TIMEOUT);
> + if (ret) {
> + dev_err(priv->dev, "HSIO_PM_REQ_CORE_RST is set\n");
> + return ret;
> + }
> + }
> +
> + /* Polling to check the PHY is ready or not. */
> + if (pmix->idx == IMX8Q_HSIO_LANE1_PCIE_PHY)
> + cond = HSIO_LANE1_TX_PLL_LOCK;
> + else
> + cond = HSIO_LANE0_TX_PLL_LOCK;
In SATA mode, don't you need LANE2? Or you should have exited above?
> +
> + ret = regmap_read_poll_timeout(priv->phy, pmix->phy_off + HSIO_PHY_STS0,
> + val, ((val & cond) == cond),
> + PHY_INIT_WAIT_USLEEP_MAX,
> + PHY_INIT_WAIT_TIMEOUT);
> + if (ret) {
> + dev_err(priv->dev, "IMX8Q PHY%d PLL lock timeout\n", pmix->idx);
> + return ret;
> + }
> + dev_info(priv->dev, "IMX8Q PHY%d PLL is locked\n", pmix->idx);
These info level prints should be debug level IMO.
> +
> + if (pmix->pmix_mode == PHY_MODE_SATA) {
> + cond = HSIO_REG48_PMA_RDY;
> + ret = read_poll_timeout(readb, val, ((val & cond) == cond),
> + PHY_INIT_WAIT_USLEEP_MAX,
> + PHY_INIT_WAIT_TIMEOUT, false,
> + priv->base + HSIO_REG48_PMA_STATUS);
> + if (ret)
> + dev_err(priv->dev, "PHY calibration is timeout\n");
> + else
> + dev_info(priv->dev, "PHY calibration is done\n");
> + }
This function is a bunch of 'if SATA' or 'if PCIE' blocks which is hard
to follow. I think it would be easier to follow if you had a specific
power_on function for each mode which can then call any common helpers
(like polling for PLL lock).
And consider if mode specific stuff can go into set_mode() hook instead.
> +
> + return ret;
> +}
> +
> +static int imx_hsio_set_mode(struct phy *phy, enum phy_mode mode,
> + int submode)
> +{
> + u32 val;
> + struct imx_hsio_phy_mix *pmix = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = pmix->priv;
> +
> + if (pmix->pmix_mode != mode)
> + return -EINVAL;
> +
> + val = (mode == PHY_MODE_PCIE) ? HSIO_MODE_PCIE : HSIO_MODE_SATA;
> + val = FIELD_PREP(HSIO_MODE_MASK, val);
> + regmap_update_bits(priv->phy, pmix->phy_off + HSIO_CTRL0,
> + HSIO_MODE_MASK, val);
> +
> + switch (submode) {
> + case PHY_MODE_PCIE_RC:
> + val = FIELD_PREP(HSIO_DEVICE_TYPE_MASK, PCI_EXP_TYPE_ROOT_PORT);
> + break;
> + case PHY_MODE_PCIE_EP:
> + val = FIELD_PREP(HSIO_DEVICE_TYPE_MASK, PCI_EXP_TYPE_ENDPOINT);
> + break;
> + default: /* Support only PCIe EP and RC now. */
> + return 0;
> + }
> + if (submode)
> + regmap_update_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL0,
> + HSIO_DEVICE_TYPE_MASK, val);
> +
> + return 0;
> +}
> +
> +static int imx_hsio_set_speed(struct phy *phy, int speed)
> +{
> + struct imx_hsio_phy_mix *pmix = phy_get_drvdata(phy);
> + struct imx_hsio_priv *priv = pmix->priv;
> +
> + regmap_update_bits(priv->ctrl, pmix->ctrl_off + HSIO_CTRL2,
> + HSIO_LTSSM_ENABLE,
> + speed ? HSIO_LTSSM_ENABLE : 0);
> + return 0;
> +}
> +
> +static const struct phy_ops imx_hsio_ops = {
> + .init = imx_hsio_init,
> + .exit = imx_hsio_exit,
> + .power_on = imx_hsio_power_on,
> + .set_mode = imx_hsio_set_mode,
> + .set_speed = imx_hsio_set_speed,
> + .owner = THIS_MODULE,
> +};
> +
> +static const struct imx_hsio_drvdata imx8qxp_hsio_drvdata = {
> + .phy_mix_num = 0x1,
> +};
> +
> +static const struct imx_hsio_drvdata imx_hsio_drvdata = {
> + .phy_mix_num = 0x4,
> +};
> +
> +static const struct of_device_id imx_hsio_of_match[] = {
> + {.compatible = "fsl,imx8qm-hsio", .data = &imx_hsio_drvdata},
> + {.compatible = "fsl,imx8qxp-hsio", .data = &imx8qxp_hsio_drvdata},
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, imx_hsio_of_match);
> +
> +static struct phy *imx_hsio_xlate(struct device *dev,
> + const struct of_phandle_args *args)
> +{
> + struct imx_hsio_priv *priv = dev_get_drvdata(dev);
> + int phy_type = args->args[0];
> + int ctrl_index = args->args[1];
> + int idx, lane_mask = args->args[2];
> +
> + idx = imx_hsio_get_idx(phy_type, ctrl_index, lane_mask);
> + if (idx < 0 || idx >= priv->drvdata->phy_mix_num)
> + return ERR_PTR(-EINVAL);
> + priv->pmix[idx].phy_type = phy_type;
> + priv->pmix[idx].ctrl_index = ctrl_index;
> + priv->pmix[idx].idx = idx;
> +
> + return priv->pmix[idx].phy;
> +}
> +
> +static int imx_hsio_probe(struct platform_device *pdev)
> +{
> + int i;
> + void __iomem *off;
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev->of_node;
> + const struct of_device_id *of_id;
> + struct imx_hsio_priv *priv;
> + struct phy_provider *provider;
> +
> + of_id = of_match_device(imx_hsio_of_match, dev);
> + if (!of_id)
> + return -EINVAL;
This driver only works with DT. We've entered probe because matching
happened. How could this fail?
> +
> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> + priv->dev = &pdev->dev;
> + priv->drvdata = of_device_get_match_data(dev);
> +
> + /* Get HSIO configuration mode */
> + of_property_read_u32(np, "fsl,hsio-cfg", &priv->hsio_cfg);
> + /* Get PHY refclk pad mode */
> + if (of_property_read_u32(np, "fsl,refclk-pad-mode", &priv->refclk_pad))
> + priv->refclk_pad = IMX8_PCIE_REFCLK_PAD_OUTPUT;
> +
> + priv->base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(priv->base))
> + return PTR_ERR(priv->base);
> +
> + off = devm_platform_ioremap_resource_byname(pdev, "phy");
> + priv->phy = devm_regmap_init_mmio(dev, off, ®map_config);
> + if (IS_ERR(priv->phy))
> + return dev_err_probe(dev, PTR_ERR(priv->phy),
> + "unable to find phy csr registers\n");
> +
> + off = devm_platform_ioremap_resource_byname(pdev, "ctrl");
> + priv->ctrl = devm_regmap_init_mmio(dev, off, ®map_config);
> + if (IS_ERR(priv->ctrl))
> + return dev_err_probe(dev, PTR_ERR(priv->ctrl),
> + "unable to find ctrl csr registers\n");
> +
> + off = devm_platform_ioremap_resource_byname(pdev, "misc");
> + priv->misc = devm_regmap_init_mmio(dev, off, ®map_config);
> + if (IS_ERR(priv->misc))
> + return dev_err_probe(dev, PTR_ERR(priv->misc),
> + "unable to find misc csr registers\n");
> +
> + for (i = 0; i < priv->drvdata->phy_mix_num; i++) {
> + struct imx_hsio_phy_mix *pmix = &priv->pmix[i];
> + struct phy *phy;
> +
> + memset(pmix, 0, sizeof(*pmix));
> +
> + phy = devm_phy_create(&pdev->dev, NULL, &imx_hsio_ops);
You have up to 3 phys, why do you register 4?
> + if (IS_ERR(phy))
> + return PTR_ERR(phy);
> +
> + pmix->priv = priv;
> + pmix->phy = phy;
> + pmix->idx = i;
> + phy_set_drvdata(phy, pmix);
> + }
> +
> + dev_set_drvdata(dev, priv);
> + dev_set_drvdata(&pdev->dev, priv);
> +
> + provider = devm_of_phy_provider_register(&pdev->dev, imx_hsio_xlate);
> +
> + return PTR_ERR_OR_ZERO(provider);
> +}
> +
> +static struct platform_driver imx_hsio_driver = {
> + .probe = imx_hsio_probe,
> + .driver = {
> + .name = "imx8qm-hsio-phy",
> + .of_match_table = imx_hsio_of_match,
> + }
> +};
> +module_platform_driver(imx_hsio_driver);
> +
> +MODULE_DESCRIPTION("FSL IMX8QM HSIO SERDES PHY driver");
> +MODULE_LICENSE("GPL");
> --
> 2.37.1
>
More information about the linux-arm-kernel
mailing list