[PATCH net-next v2 02/15] net: dsa: mt7530: refactor MT7530_PMCR_P()
Arınç ÜNAL via B4 Relay
devnull+arinc.unal.arinc9.com at kernel.org
Mon Apr 22 00:15:09 PDT 2024
From: Arınç ÜNAL <arinc.unal at arinc9.com>
The MT7530_PMCR_P() registers are on MT7530, MT7531, and the switch on the
MT7988 SoC. Rename the definition for them to MT753X_PMCR_P(). Bit 15 is
for MT7530 only. Add MT7530 prefix to the definition for bit 15.
Use GENMASK and FIELD_PREP for PMCR_IFG_XMIT().
Rename PMCR_TX_EN and PMCR_RX_EN to PMCR_MAC_TX_EN and PMCR_MAC_TX_EN to
follow the naming on the "MT7621 Giga Switch Programming Guide v0.3",
"MT7531 Reference Manual for Development Board v1.0", and "MT7988A Wi-Fi 7
Generation Router Platform: Datasheet (Open Version) v0.1" documents.
These documents show that PMCR_RX_FC_EN is at bit 5. Correct this along
with renaming it to PMCR_FORCE_RX_FC_EN, and the same for PMCR_TX_FC_EN.
Remove PMCR_SPEED_MASK which doesn't have a use.
Rename the force mode definitions for MT7531 to FORCE_MODE. Add MASK at the
end for the mask that includes all force mode definitions.
Signed-off-by: Arınç ÜNAL <arinc.unal at arinc9.com>
---
drivers/net/dsa/mt7530.c | 24 ++++++++++----------
drivers/net/dsa/mt7530.h | 58 +++++++++++++++++++++++++-----------------------
2 files changed, 42 insertions(+), 40 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 04795ef8ebd7..8dee9cee1104 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -896,7 +896,7 @@ static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
val &= ~MHWTRAP_P5_MAC_SEL & ~MHWTRAP_P5_DIS;
/* Setup the MAC by default for the cpu port */
- mt7530_write(priv, MT7530_PMCR_P(5), 0x56300);
+ mt7530_write(priv, MT753X_PMCR_P(5), 0x56300);
break;
case P5_INTF_SEL_GMAC5:
/* MT7530_P5_MODE_GMAC: P5 -> External phy or 2nd GMAC */
@@ -2444,8 +2444,8 @@ mt7530_setup(struct dsa_switch *ds)
/* Clear link settings and enable force mode to force link down
* on all ports until they're enabled later.
*/
- mt7530_rmw(priv, MT7530_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
- PMCR_FORCE_MODE, PMCR_FORCE_MODE);
+ mt7530_rmw(priv, MT753X_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
+ MT7530_FORCE_MODE, MT7530_FORCE_MODE);
/* Disable forwarding by default on all ports */
mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
@@ -2555,8 +2555,8 @@ mt7531_setup_common(struct dsa_switch *ds)
/* Clear link settings and enable force mode to force link down
* on all ports until they're enabled later.
*/
- mt7530_rmw(priv, MT7530_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
- MT7531_FORCE_MODE, MT7531_FORCE_MODE);
+ mt7530_rmw(priv, MT753X_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
+ MT7531_FORCE_MODE_MASK, MT7531_FORCE_MODE_MASK);
/* Disable forwarding by default on all ports */
mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
@@ -2639,7 +2639,7 @@ mt7531_setup(struct dsa_switch *ds)
/* Force link down on all ports before internal reset */
for (i = 0; i < MT7530_NUM_PORTS; i++)
- mt7530_write(priv, MT7530_PMCR_P(i), MT7531_FORCE_LNK);
+ mt7530_write(priv, MT753X_PMCR_P(i), MT7531_FORCE_MODE_LNK);
/* Reset the switch through internal reset */
mt7530_write(priv, MT7530_SYS_CTRL, SYS_CTRL_SW_RST | SYS_CTRL_REG_RST);
@@ -2881,7 +2881,7 @@ mt753x_phylink_mac_config(struct phylink_config *config, unsigned int mode,
/* Are we connected to external phy */
if (port == 5 && dsa_is_user_port(ds, 5))
- mt7530_set(priv, MT7530_PMCR_P(port), PMCR_EXT_PHY);
+ mt7530_set(priv, MT753X_PMCR_P(port), PMCR_EXT_PHY);
}
static void mt753x_phylink_mac_link_down(struct phylink_config *config,
@@ -2891,7 +2891,7 @@ static void mt753x_phylink_mac_link_down(struct phylink_config *config,
struct dsa_port *dp = dsa_phylink_to_port(config);
struct mt7530_priv *priv = dp->ds->priv;
- mt7530_clear(priv, MT7530_PMCR_P(dp->index), PMCR_LINK_SETTINGS_MASK);
+ mt7530_clear(priv, MT753X_PMCR_P(dp->index), PMCR_LINK_SETTINGS_MASK);
}
static void mt753x_phylink_mac_link_up(struct phylink_config *config,
@@ -2905,7 +2905,7 @@ static void mt753x_phylink_mac_link_up(struct phylink_config *config,
struct mt7530_priv *priv = dp->ds->priv;
u32 mcr;
- mcr = PMCR_RX_EN | PMCR_TX_EN | PMCR_FORCE_LNK;
+ mcr = PMCR_MAC_RX_EN | PMCR_MAC_TX_EN | PMCR_FORCE_LNK;
switch (speed) {
case SPEED_1000:
@@ -2920,9 +2920,9 @@ static void mt753x_phylink_mac_link_up(struct phylink_config *config,
if (duplex == DUPLEX_FULL) {
mcr |= PMCR_FORCE_FDX;
if (tx_pause)
- mcr |= PMCR_TX_FC_EN;
+ mcr |= PMCR_FORCE_TX_FC_EN;
if (rx_pause)
- mcr |= PMCR_RX_FC_EN;
+ mcr |= PMCR_FORCE_RX_FC_EN;
}
if (mode == MLO_AN_PHY && phydev && phy_init_eee(phydev, false) >= 0) {
@@ -2937,7 +2937,7 @@ static void mt753x_phylink_mac_link_up(struct phylink_config *config,
}
}
- mt7530_set(priv, MT7530_PMCR_P(dp->index), mcr);
+ mt7530_set(priv, MT753X_PMCR_P(dp->index), mcr);
}
static void mt753x_phylink_get_caps(struct dsa_switch *ds, int port,
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index f7c5355c1642..7d7abb67202f 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -304,44 +304,46 @@ enum mt7530_vlan_port_acc_frm {
#define G0_PORT_VID_DEF G0_PORT_VID(0)
/* Register for port MAC control register */
-#define MT7530_PMCR_P(x) (0x3000 + ((x) * 0x100))
-#define PMCR_IFG_XMIT(x) (((x) & 0x3) << 18)
+#define MT753X_PMCR_P(x) (0x3000 + ((x) * 0x100))
+#define PMCR_IFG_XMIT_MASK GENMASK(19, 18)
+#define PMCR_IFG_XMIT(x) FIELD_PREP(PMCR_IFG_XMIT_MASK, x)
#define PMCR_EXT_PHY BIT(17)
#define PMCR_MAC_MODE BIT(16)
-#define PMCR_FORCE_MODE BIT(15)
-#define PMCR_TX_EN BIT(14)
-#define PMCR_RX_EN BIT(13)
+#define MT7530_FORCE_MODE BIT(15)
+#define PMCR_MAC_TX_EN BIT(14)
+#define PMCR_MAC_RX_EN BIT(13)
#define PMCR_BACKOFF_EN BIT(9)
#define PMCR_BACKPR_EN BIT(8)
#define PMCR_FORCE_EEE1G BIT(7)
#define PMCR_FORCE_EEE100 BIT(6)
-#define PMCR_TX_FC_EN BIT(5)
-#define PMCR_RX_FC_EN BIT(4)
+#define PMCR_FORCE_RX_FC_EN BIT(5)
+#define PMCR_FORCE_TX_FC_EN BIT(4)
#define PMCR_FORCE_SPEED_1000 BIT(3)
#define PMCR_FORCE_SPEED_100 BIT(2)
#define PMCR_FORCE_FDX BIT(1)
#define PMCR_FORCE_LNK BIT(0)
-#define PMCR_SPEED_MASK (PMCR_FORCE_SPEED_100 | \
- PMCR_FORCE_SPEED_1000)
-#define MT7531_FORCE_LNK BIT(31)
-#define MT7531_FORCE_SPD BIT(30)
-#define MT7531_FORCE_DPX BIT(29)
-#define MT7531_FORCE_RX_FC BIT(28)
-#define MT7531_FORCE_TX_FC BIT(27)
-#define MT7531_FORCE_EEE100 BIT(26)
-#define MT7531_FORCE_EEE1G BIT(25)
-#define MT7531_FORCE_MODE (MT7531_FORCE_LNK | \
- MT7531_FORCE_SPD | \
- MT7531_FORCE_DPX | \
- MT7531_FORCE_RX_FC | \
- MT7531_FORCE_TX_FC | \
- MT7531_FORCE_EEE100 | \
- MT7531_FORCE_EEE1G)
-#define PMCR_LINK_SETTINGS_MASK (PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
- PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
- PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
- PMCR_FORCE_FDX | PMCR_FORCE_LNK | \
- PMCR_FORCE_EEE1G | PMCR_FORCE_EEE100)
+#define MT7531_FORCE_MODE_LNK BIT(31)
+#define MT7531_FORCE_MODE_SPD BIT(30)
+#define MT7531_FORCE_MODE_DPX BIT(29)
+#define MT7531_FORCE_MODE_RX_FC BIT(28)
+#define MT7531_FORCE_MODE_TX_FC BIT(27)
+#define MT7531_FORCE_MODE_EEE100 BIT(26)
+#define MT7531_FORCE_MODE_EEE1G BIT(25)
+#define MT7531_FORCE_MODE_MASK (MT7531_FORCE_MODE_LNK | \
+ MT7531_FORCE_MODE_SPD | \
+ MT7531_FORCE_MODE_DPX | \
+ MT7531_FORCE_MODE_RX_FC | \
+ MT7531_FORCE_MODE_TX_FC | \
+ MT7531_FORCE_MODE_EEE100 | \
+ MT7531_FORCE_MODE_EEE1G)
+#define PMCR_LINK_SETTINGS_MASK (PMCR_MAC_TX_EN | PMCR_MAC_RX_EN | \
+ PMCR_FORCE_EEE1G | \
+ PMCR_FORCE_EEE100 | \
+ PMCR_FORCE_RX_FC_EN | \
+ PMCR_FORCE_TX_FC_EN | \
+ PMCR_FORCE_SPEED_1000 | \
+ PMCR_FORCE_SPEED_100 | \
+ PMCR_FORCE_FDX | PMCR_FORCE_LNK)
#define MT7530_PMEEECR_P(x) (0x3004 + (x) * 0x100)
#define WAKEUP_TIME_1000(x) (((x) & 0xFF) << 24)
--
2.40.1
More information about the linux-arm-kernel
mailing list