[PATCH v2] ARM: dts: bcm2835: Enable 3D rendering through V3D
Andre Przywara
andre.przywara at arm.com
Mon Apr 15 09:54:33 PDT 2024
On Mon, 15 Apr 2024 13:00:39 -0300
Maíra Canal <mcanal at igalia.com> wrote:
Hi,
> RPi 0-3 is packed with a GPU that provides 3D rendering capabilities to
> the RPi. Currently, the downstream kernel uses an overlay to enable the
> GPU and use GPU hardware acceleration. When deploying a mainline kernel
> to the RPi 0-3, we end up without any GPU hardware acceleration
> (essentially, we can't use the OpenGL driver).
>
> Therefore, enable the V3D core for the RPi 0-3 in the mainline kernel.
So I think Krzysztof's initial comment still stands: What does that patch
actually change? If I build those DTBs as of now, none of them has a
status property in the v3d node. Which means it's enabled:
https://github.com/devicetree-org/devicetree-specification/blob/main/source/chapter2-devicetree-basics.rst#status
So adding an explicit 'status = "okay";' doesn't make a difference.
What do I miss here?
Cheers,
Andre
> Signed-off-by: Maíra Canal <mcanal at igalia.com>
> ---
>
> v1 -> v2: https://lore.kernel.org/dri-devel/41694292-af1f-4760-a7b6-101ed5dd6f9d@gmx.net/T/
>
> * As mentioned by Krzysztof, enabling should be done in last place of
> override/extend. Therefore, I'm disabling V3D in the common dtsi
> and enabling in the last place of extend, i.e. the RPi DTS files.
>
> arch/arm/boot/dts/broadcom/bcm2835-common.dtsi | 1 +
> arch/arm/boot/dts/broadcom/bcm2835-rpi-a-plus.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2835-rpi-a.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2835-rpi-b-plus.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2835-rpi-b-rev2.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2835-rpi-b.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1-io1.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2835-rpi-zero-w.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2835-rpi-zero.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2836-rpi-2-b.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b-plus.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3-io3.dts | 4 ++++
> arch/arm/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts | 4 ++++
> 15 files changed, 57 insertions(+)
>
> diff --git a/arch/arm/boot/dts/broadcom/bcm2835-common.dtsi b/arch/arm/boot/dts/broadcom/bcm2835-common.dtsi
> index 9261b67dbee1..69e34831de51 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2835-common.dtsi
> +++ b/arch/arm/boot/dts/broadcom/bcm2835-common.dtsi
> @@ -139,6 +139,7 @@ v3d: v3d at 7ec00000 {
> compatible = "brcm,bcm2835-v3d";
> reg = <0x7ec00000 0x1000>;
> interrupts = <1 10>;
> + status = "disabled";
> };
>
> vc4: gpu {
> diff --git a/arch/arm/boot/dts/broadcom/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a-plus.dts
> index 069b48272aa5..495ab1dfd2ce 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2835-rpi-a-plus.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a-plus.dts
> @@ -128,3 +128,7 @@ &uart0 {
> pinctrl-0 = <&uart0_gpio14>;
> status = "okay";
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2835-rpi-a.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a.dts
> index 2726c00431e8..4634d88ce3af 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2835-rpi-a.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a.dts
> @@ -121,3 +121,7 @@ &uart0 {
> pinctrl-0 = <&uart0_gpio14>;
> status = "okay";
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-plus.dts
> index c57b999a4520..45fa0f6851fc 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-plus.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-plus.dts
> @@ -130,3 +130,7 @@ &uart0 {
> pinctrl-0 = <&uart0_gpio14>;
> status = "okay";
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-rev2.dts
> index ae6d3a9586ab..c1dac5d704aa 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-rev2.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-rev2.dts
> @@ -121,3 +121,7 @@ &uart0 {
> pinctrl-0 = <&uart0_gpio14>;
> status = "okay";
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2835-rpi-b.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b.dts
> index 72764be75a79..72ca31f2a7d6 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2835-rpi-b.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b.dts
> @@ -115,3 +115,7 @@ &uart0 {
> pinctrl-0 = <&uart0_gpio14>;
> status = "okay";
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1-io1.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1-io1.dts
> index 3f9d198ac3ab..881a07d2f28f 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1-io1.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1-io1.dts
> @@ -95,3 +95,7 @@ &uart0 {
> pinctrl-0 = <&uart0_gpio14>;
> status = "okay";
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero-w.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero-w.dts
> index 1f0b163e400c..1c7324067442 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero-w.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero-w.dts
> @@ -134,6 +134,10 @@ &uart1 {
> status = "okay";
> };
>
> +&v3d {
> + status = "okay";
> +};
> +
> &wifi_pwrseq {
> reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
> };
> diff --git a/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero.dts
> index 539c19c10946..1568ddc78f22 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero.dts
> @@ -117,3 +117,7 @@ &uart0 {
> pinctrl-0 = <&uart0_gpio14>;
> status = "okay";
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/broadcom/bcm2836-rpi-2-b.dts
> index 79918033750e..8fab6293d1c7 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2836-rpi-2-b.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2836-rpi-2-b.dts
> @@ -129,3 +129,7 @@ &uart0 {
> pinctrl-0 = <&uart0_gpio14>;
> status = "okay";
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
> index 3548306dfbcb..dc45b56054c7 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
> @@ -156,3 +156,7 @@ &uart1 {
> pinctrl-0 = <&uart1_gpio14>;
> status = "okay";
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b-plus.dts
> index 2f1800cbc522..ce3a9f7ff529 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b-plus.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b-plus.dts
> @@ -161,3 +161,7 @@ &uart1 {
> &wifi_pwrseq {
> reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b.dts
> index 61270340075c..e398546d105b 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b.dts
> @@ -149,6 +149,10 @@ &sdhost {
> bus-width = <4>;
> };
>
> +&v3d {
> + status = "okay";
> +};
> +
> &wifi_pwrseq {
> reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
> };
> diff --git a/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3-io3.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3-io3.dts
> index 72d26d130efa..50471ada79b3 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3-io3.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3-io3.dts
> @@ -94,3 +94,7 @@ &uart0 {
> pinctrl-0 = <&uart0_gpio14>;
> status = "okay";
> };
> +
> +&v3d {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts
> index 85cf594724ef..876f697e7300 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts
> @@ -132,6 +132,10 @@ &uart1 {
> status = "okay";
> };
>
> +&v3d {
> + status = "okay";
> +};
> +
> &wifi_pwrseq {
> reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
> };
More information about the linux-arm-kernel
mailing list