[PATCH] bus: ti-sysc: Fix SYSC_QUIRK_SWSUP_SIDLE_ACT handling for uart wake-up

[Tony Lindgren]

The uarts should be tagged with SYSC_QUIRK_SWSUP_SIDLE instead of
SYSC_QUIRK_SWSUP_SIDLE_ACT. The difference is that SYSC_QUIRK_SWSUP_SIDLE
is used to force idle target modules rather than block idle during usage.

The SYSC_QUIRK_SWSUP_SIDLE_ACT should disable autoidle and wake-up when
a target module is active, and configure autoidle and wake-up when a
target module is inactive. We are missing configuring the target module
on sysc_disable_module(), and missing toggling of the wake-up bit.

Let's fix the issue to allow uart wake-up to work.

Fixes: fb685f1c190e ("bus: ti-sysc: Handle swsup idle mode quirks")
Signed-off-by: Tony Lindgren <tony at atomide.com>
---
 drivers/bus/ti-sysc.c | 22 +++++++++++++++++-----
 1 file changed, 17 insertions(+), 5 deletions(-)

diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c
--- a/drivers/bus/ti-sysc.c
+++ b/drivers/bus/ti-sysc.c
@@ -1097,6 +1097,11 @@ static int sysc_enable_module(struct device *dev)
 	if (ddata->cfg.quirks & (SYSC_QUIRK_SWSUP_SIDLE |
 				 SYSC_QUIRK_SWSUP_SIDLE_ACT)) {
 		best_mode = SYSC_IDLE_NO;
+
+		/* Clear WAKEUP */
+		if (regbits->enwkup_shift >= 0 &&
+		    ddata->cfg.sysc_val & BIT(regbits->enwkup_shift))
+			reg &= ~BIT(regbits->enwkup_shift);
 	} else {
 		best_mode = fls(ddata->cfg.sidlemodes) - 1;
 		if (best_mode > SYSC_IDLE_MASK) {
@@ -1224,6 +1229,13 @@ static int sysc_disable_module(struct device *dev)
 		}
 	}
 
+	if (ddata->cfg.quirks & SYSC_QUIRK_SWSUP_SIDLE_ACT) {
+		/* Set WAKEUP */
+		if (regbits->enwkup_shift >= 0 &&
+		    ddata->cfg.sysc_val & BIT(regbits->enwkup_shift))
+			reg |= BIT(regbits->enwkup_shift);
+	}
+
 	reg &= ~(SYSC_IDLE_MASK << regbits->sidle_shift);
 	reg |= best_mode << regbits->sidle_shift;
 	if (regbits->autoidle_shift >= 0 &&
@@ -1518,16 +1530,16 @@ struct sysc_revision_quirk {
 static const struct sysc_revision_quirk sysc_revision_quirks[] = {
 	/* These drivers need to be fixed to not use pm_runtime_irq_safe() */
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x00000046, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x00000052, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	/* Uarts on omap4 and later */
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x50411e03, 0xffff00ff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47422e03, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47424e03, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 
 	/* Quirks that need to be set based on the module address */
 	SYSC_QUIRK("mcpdm", 0x40132000, 0, 0x10, -ENODEV, 0x50000800, 0xffffffff,
-- 
2.41.0