[PATCH net-next v6 4/7] ARM: dts: nxp: Fix some common switch mistakes
Linus Walleij
linus.walleij at linaro.org
Tue Oct 24 02:24:56 PDT 2023
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- switch0 at 0 is not OK, should be ethernet-switch at 0
- ports should be ethernet-ports
- port should be ethernet-port
- phy should be ethernet-phy
Reviewed-by: Andrew Lunn <andrew at lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts | 14 ++---
arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts | 70 ++++++++++++------------
arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts | 18 +++---
arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts | 20 +++----
arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts | 18 +++---
5 files changed, 70 insertions(+), 70 deletions(-)
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts
index 1a19aec8957b..7e72f860c3c5 100644
--- a/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts
@@ -162,7 +162,7 @@ mdio1: mdio {
suppress-preamble;
status = "okay";
- switch0: switch0 at 0 {
+ switch0: ethernet-switch at 0 {
compatible = "marvell,mv88e6085";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_switch>;
@@ -173,26 +173,26 @@ switch0: switch0 at 0 {
interrupt-controller;
#interrupt-cells = <2>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port at 0 {
+ ethernet-port at 0 {
reg = <0>;
label = "eth_cu_1000_1";
};
- port at 1 {
+ ethernet-port at 1 {
reg = <1>;
label = "eth_cu_1000_2";
};
- port at 2 {
+ ethernet-port at 2 {
reg = <2>;
label = "eth_cu_1000_3";
};
- port at 5 {
+ ethernet-port at 5 {
reg = <5>;
label = "eth_fc_1000_1";
phy-mode = "1000base-x";
@@ -200,7 +200,7 @@ port at 5 {
sfp = <&sff>;
};
- port at 6 {
+ ethernet-port at 6 {
reg = <6>;
phy-mode = "rmii";
ethernet = <&fec1>;
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts
index df1335492a19..77492eeea450 100644
--- a/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts
@@ -47,17 +47,17 @@ mdio_mux_1: mdio at 1 {
#address-cells = <1>;
#size-cells = <0>;
- switch0: switch0 at 0 {
+ switch0: ethernet-switch at 0 {
compatible = "marvell,mv88e6190";
reg = <0>;
dsa,member = <0 0>;
eeprom-length = <65536>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port at 0 {
+ ethernet-port at 0 {
reg = <0>;
phy-mode = "rmii";
ethernet = <&fec1>;
@@ -68,37 +68,37 @@ fixed-link {
};
};
- port at 1 {
+ ethernet-port at 1 {
reg = <1>;
label = "aib2main_1";
};
- port at 2 {
+ ethernet-port at 2 {
reg = <2>;
label = "aib2main_2";
};
- port at 3 {
+ ethernet-port at 3 {
reg = <3>;
label = "eth_cu_1000_5";
};
- port at 4 {
+ ethernet-port at 4 {
reg = <4>;
label = "eth_cu_1000_6";
};
- port at 5 {
+ ethernet-port at 5 {
reg = <5>;
label = "eth_cu_1000_4";
};
- port at 6 {
+ ethernet-port at 6 {
reg = <6>;
label = "eth_cu_1000_7";
};
- port at 7 {
+ ethernet-port at 7 {
reg = <7>;
label = "modem_pic";
@@ -108,7 +108,7 @@ fixed-link {
};
};
- switch0port10: port at 10 {
+ switch0port10: ethernet-port at 10 {
reg = <10>;
label = "dsa";
phy-mode = "xgmii";
@@ -130,32 +130,32 @@ mdio_mux_2: mdio at 2 {
#address-cells = <1>;
#size-cells = <0>;
- switch1: switch1 at 0 {
+ switch1: ethernet-switch at 0 {
compatible = "marvell,mv88e6190";
reg = <0>;
dsa,member = <0 1>;
eeprom-length = <65536>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port at 1 {
+ ethernet-port at 1 {
reg = <1>;
label = "eth_cu_1000_3";
};
- port at 2 {
+ ethernet-port at 2 {
reg = <2>;
label = "eth_cu_100_2";
};
- port at 3 {
+ ethernet-port at 3 {
reg = <3>;
label = "eth_cu_100_3";
};
- switch1port9: port at 9 {
+ switch1port9: ethernet-port at 9 {
reg = <9>;
label = "dsa";
phy-mode = "xgmii";
@@ -168,7 +168,7 @@ fixed-link {
};
};
- switch1port10: port at 10 {
+ switch1port10: ethernet-port at 10 {
reg = <10>;
label = "dsa";
phy-mode = "xgmii";
@@ -188,17 +188,17 @@ mdio_mux_4: mdio at 4 {
#address-cells = <1>;
#size-cells = <0>;
- switch2: switch2 at 0 {
+ switch2: ethernet-switch at 0 {
compatible = "marvell,mv88e6190";
reg = <0>;
dsa,member = <0 2>;
eeprom-length = <65536>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port at 2 {
+ ethernet-port at 2 {
reg = <2>;
label = "eth_fc_1000_2";
phy-mode = "1000base-x";
@@ -206,7 +206,7 @@ port at 2 {
sfp = <&sff1>;
};
- port at 3 {
+ ethernet-port at 3 {
reg = <3>;
label = "eth_fc_1000_3";
phy-mode = "1000base-x";
@@ -214,7 +214,7 @@ port at 3 {
sfp = <&sff2>;
};
- port at 4 {
+ ethernet-port at 4 {
reg = <4>;
label = "eth_fc_1000_4";
phy-mode = "1000base-x";
@@ -222,7 +222,7 @@ port at 4 {
sfp = <&sff3>;
};
- port at 5 {
+ ethernet-port at 5 {
reg = <5>;
label = "eth_fc_1000_5";
phy-mode = "1000base-x";
@@ -230,7 +230,7 @@ port at 5 {
sfp = <&sff4>;
};
- port at 6 {
+ ethernet-port at 6 {
reg = <6>;
label = "eth_fc_1000_6";
phy-mode = "1000base-x";
@@ -238,7 +238,7 @@ port at 6 {
sfp = <&sff5>;
};
- port at 7 {
+ ethernet-port at 7 {
reg = <7>;
label = "eth_fc_1000_7";
phy-mode = "1000base-x";
@@ -246,7 +246,7 @@ port at 7 {
sfp = <&sff6>;
};
- port at 9 {
+ ethernet-port at 9 {
reg = <9>;
label = "eth_fc_1000_1";
phy-mode = "1000base-x";
@@ -254,7 +254,7 @@ port at 9 {
sfp = <&sff0>;
};
- switch2port10: port at 10 {
+ switch2port10: ethernet-port at 10 {
reg = <10>;
label = "dsa";
phy-mode = "2500base-x";
@@ -276,17 +276,17 @@ mdio_mux_8: mdio at 8 {
#address-cells = <1>;
#size-cells = <0>;
- switch3: switch3 at 0 {
+ switch3: ethernet-switch at 0 {
compatible = "marvell,mv88e6190";
reg = <0>;
dsa,member = <0 3>;
eeprom-length = <65536>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port at 2 {
+ ethernet-port at 2 {
reg = <2>;
label = "eth_fc_1000_8";
phy-mode = "1000base-x";
@@ -294,7 +294,7 @@ port at 2 {
sfp = <&sff7>;
};
- port at 3 {
+ ethernet-port at 3 {
reg = <3>;
label = "eth_fc_1000_9";
phy-mode = "1000base-x";
@@ -302,7 +302,7 @@ port at 3 {
sfp = <&sff8>;
};
- port at 4 {
+ ethernet-port at 4 {
reg = <4>;
label = "eth_fc_1000_10";
phy-mode = "1000base-x";
@@ -310,7 +310,7 @@ port at 4 {
sfp = <&sff9>;
};
- switch3port9: port at 9 {
+ switch3port9: ethernet-port at 9 {
reg = <9>;
label = "dsa";
phy-mode = "2500base-x";
@@ -322,7 +322,7 @@ fixed-link {
};
};
- switch3port10: port at 10 {
+ switch3port10: ethernet-port at 10 {
reg = <10>;
label = "dsa";
phy-mode = "xgmii";
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts
index 1461804ecaea..2a490464660c 100644
--- a/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts
@@ -123,7 +123,7 @@ mdio1: mdio {
suppress-preamble;
status = "okay";
- switch0: switch0 at 0 {
+ switch0: ethernet-switch at 0 {
compatible = "marvell,mv88e6190";
pinctrl-0 = <&pinctrl_gpio_switch0>;
pinctrl-names = "default";
@@ -134,11 +134,11 @@ switch0: switch0 at 0 {
interrupt-controller;
#interrupt-cells = <2>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port at 0 {
+ ethernet-port at 0 {
reg = <0>;
phy-mode = "rmii";
ethernet = <&fec1>;
@@ -149,32 +149,32 @@ fixed-link {
};
};
- port at 1 {
+ ethernet-port at 1 {
reg = <1>;
label = "eth_cu_1000_1";
};
- port at 2 {
+ ethernet-port at 2 {
reg = <2>;
label = "eth_cu_1000_2";
};
- port at 3 {
+ ethernet-port at 3 {
reg = <3>;
label = "eth_cu_1000_3";
};
- port at 4 {
+ ethernet-port at 4 {
reg = <4>;
label = "eth_cu_1000_4";
};
- port at 5 {
+ ethernet-port at 5 {
reg = <5>;
label = "eth_cu_1000_5";
};
- port at 6 {
+ ethernet-port at 6 {
reg = <6>;
label = "eth_cu_1000_6";
};
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
index 463c2452b9b7..078d8699e16d 100644
--- a/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
@@ -112,7 +112,7 @@ mdio1: mdio {
suppress-preamble;
status = "okay";
- switch0: switch0 at 0 {
+ switch0: ethernet-switch at 0 {
compatible = "marvell,mv88e6190";
pinctrl-0 = <&pinctrl_gpio_switch0>;
pinctrl-names = "default";
@@ -123,11 +123,11 @@ switch0: switch0 at 0 {
interrupt-controller;
#interrupt-cells = <2>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port at 0 {
+ ethernet-port at 0 {
reg = <0>;
phy-mode = "rmii";
ethernet = <&fec1>;
@@ -138,27 +138,27 @@ fixed-link {
};
};
- port at 1 {
+ ethernet-port at 1 {
reg = <1>;
label = "eth_cu_100_3";
};
- port at 5 {
+ ethernet-port at 5 {
reg = <5>;
label = "eth_cu_1000_4";
};
- port at 6 {
+ ethernet-port at 6 {
reg = <6>;
label = "eth_cu_1000_5";
};
- port at 8 {
+ ethernet-port at 8 {
reg = <8>;
label = "eth_cu_1000_1";
};
- port at 9 {
+ ethernet-port at 9 {
reg = <9>;
label = "eth_cu_1000_2";
phy-handle = <&phy9>;
@@ -167,12 +167,12 @@ port at 9 {
};
};
- mdio1 {
+ mdio-external {
compatible = "marvell,mv88e6xxx-mdio-external";
#address-cells = <1>;
#size-cells = <0>;
- phy9: phy9 at 0 {
+ phy9: ethernet-phy at 0 {
compatible = "ethernet-phy-ieee802.3-c45";
pinctrl-0 = <&pinctrl_gpio_phy9>;
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts
index f5ae0d5de315..22c8f44390a9 100644
--- a/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts
@@ -137,7 +137,7 @@ mdio1: mdio {
suppress-preamble;
status = "okay";
- switch0: switch0 at 0 {
+ switch0: ethernet-switch at 0 {
compatible = "marvell,mv88e6190";
pinctrl-0 = <&pinctrl_gpio_switch0>;
pinctrl-names = "default";
@@ -148,11 +148,11 @@ switch0: switch0 at 0 {
interrupt-controller;
#interrupt-cells = <2>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port at 0 {
+ ethernet-port at 0 {
reg = <0>;
phy-mode = "rmii";
ethernet = <&fec1>;
@@ -163,32 +163,32 @@ fixed-link {
};
};
- port at 1 {
+ ethernet-port at 1 {
reg = <1>;
label = "eth_cu_1000_1";
};
- port at 2 {
+ ethernet-port at 2 {
reg = <2>;
label = "eth_cu_1000_2";
};
- port at 3 {
+ ethernet-port at 3 {
reg = <3>;
label = "eth_cu_1000_3";
};
- port at 4 {
+ ethernet-port at 4 {
reg = <4>;
label = "eth_cu_1000_4";
};
- port at 5 {
+ ethernet-port at 5 {
reg = <5>;
label = "eth_cu_1000_5";
};
- port at 6 {
+ ethernet-port at 6 {
reg = <6>;
label = "eth_cu_1000_6";
};
--
2.34.1
More information about the linux-arm-kernel
mailing list