[PATCH 1/2] arm64: dts: ti: k3-am62p: Add nodes for more IPs
Vignesh Raghavendra
vigneshr at ti.com
Thu Oct 12 00:52:16 PDT 2023
On 10/10/23 09:29, Bryan Brattlof wrote:
> From: Vignesh Raghavendra <vigneshr at ti.com>
>
> The am62px shares many of the same IP as the existing am62x family
> of SoCs, Introduce more nodes for hardware available on the am62p5.
>
> Signed-off-by: Vignesh Raghavendra <vigneshr at ti.com>
> Signed-off-by: Bryan Brattlof <bb at ti.com>
> ---
> arch/arm64/boot/dts/ti/k3-am62p-main.dtsi | 835 ++++++++++++++++++-
> arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi | 191 +++++
> arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi | 47 ++
> arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi | 67 ++
> arch/arm64/boot/dts/ti/k3-am62p.dtsi | 2 +
> 5 files changed, 1141 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
> index c24ff905437ff..b754c18c3325b 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
> @@ -40,9 +40,29 @@ gic_its: msi-controller at 1820000 {
> };
> };
>
> + main_conf: syscon at 100000 {
> + compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
simple-bus is sufficient
> + reg = <0x00 0x00100000 0x00 0x20000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x0 0x00 0x00100000 0x20000>;
> +
> + phy_gmii_sel: phy at 4044 {
> + compatible = "ti,am654-phy-gmii-sel";
> + reg = <0x4044 0x8>;
> + #phy-cells = <1>;
> + };
> +
> + epwm_tbclk: clock-controller at 4130 {
> + compatible = "ti,am62-epwm-tbclk";
> + reg = <0x4130 0x4>;
> + #clock-cells = <1>;
> + };
> + };
> +
> dmss: bus at 48000000 {
> bootph-all;
Here and elsehwere, Lets keep this property at the last, prefer to have compatible,
reg, reg-names to be at the beginning
> - compatible = "simple-mfd";
> + compatible = "simple-bus";
This is already address by [0]
[0] https://lore.kernel.org/linux-arm-kernel/20231005151302.1290363-2-vigneshr@ti.com/
> #address-cells = <2>;
> #size-cells = <2>;
> dma-ranges;
> @@ -61,6 +81,71 @@ secure_proxy_main: mailbox at 4d000000 {
> interrupt-names = "rx_012";
> interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> };
> +
> + inta_main_dmss: interrupt-controller at 48000000 {
> + compatible = "ti,sci-inta";
> + reg = <0x00 0x48000000 0x00 0x100000>;
> + #interrupt-cells = <0>;
> + interrupt-controller;
> + interrupt-parent = <&gic500>;
> + msi-controller;
> + ti,sci = <&dmsc>;
> + ti,sci-dev-id = <28>;
> + ti,interrupt-ranges = <5 69 35>;
> + ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>;
> + };
> +
> + main_bcdma: dma-controller at 485c0100 {
> + bootph-all;
> + compatible = "ti,am64-dmss-bcdma";
> + reg = <0x00 0x485c0100 0x00 0x100>,
> + <0x00 0x4c000000 0x00 0x20000>,
> + <0x00 0x4a820000 0x00 0x20000>,
> + <0x00 0x4aa40000 0x00 0x20000>,
> + <0x00 0x4bc00000 0x00 0x100000>;
> + reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt";
> + msi-parent = <&inta_main_dmss>;
> + #dma-cells = <3>;
> +
> + ti,sci = <&dmsc>;
> + ti,sci-dev-id = <26>;
> + ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
> + ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
> + ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
> + };
> +
> + main_pktdma: dma-controller at 485c0000 {
> + bootph-all;
> + compatible = "ti,am64-dmss-pktdma";
> + reg = <0x00 0x485c0000 0x00 0x100>,
> + <0x00 0x4a800000 0x00 0x20000>,
> + <0x00 0x4aa00000 0x00 0x40000>,
> + <0x00 0x4b800000 0x00 0x400000>;
> + reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt";
> + msi-parent = <&inta_main_dmss>;
> + #dma-cells = <2>;
> +
> + ti,sci = <&dmsc>;
> + ti,sci-dev-id = <30>;
> + ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */
> + <0x24>, /* CPSW_TX_CHAN */
> + <0x25>, /* SAUL_TX_0_CHAN */
> + <0x26>; /* SAUL_TX_1_CHAN */
> + ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */
> + <0x11>, /* RING_CPSW_TX_CHAN */
> + <0x12>, /* RING_SAUL_TX_0_CHAN */
> + <0x13>; /* RING_SAUL_TX_1_CHAN */
> + ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */
> + <0x2b>, /* CPSW_RX_CHAN */
> + <0x2d>, /* SAUL_RX_0_CHAN */
> + <0x2f>, /* SAUL_RX_1_CHAN */
> + <0x31>, /* SAUL_RX_2_CHAN */
> + <0x33>; /* SAUL_RX_3_CHAN */
> + ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */
> + <0x2c>, /* FLOW_CPSW_RX_CHAN */
> + <0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */
> + <0x32>; /* FLOW_SAUL_RX_2/3_CHAN */
> + };
> };
>
> dmsc: system-controller at 44043000 {
> @@ -92,6 +177,34 @@ k3_reset: reset-controller {
> };
> };
>
> + crypto: crypto at 40900000 {
> + compatible = "ti,am62-sa3ul";
> + reg = <0x00 0x40900000 0x00 0x1200>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges = <0x00 0x40900000 0x00 0x40900000 0x00 0x30000>;
> +
> + dmas = <&main_pktdma 0xf501 0>, <&main_pktdma 0x7506 0>,
> + <&main_pktdma 0x7507 0>;
> + dma-names = "tx", "rx1", "rx2";
> + };
> +
> + secure_proxy_sa3: mailbox at 43600000 {
> + bootph-all;
> + compatible = "ti,am654-secure-proxy";
> + #mbox-cells = <1>;
> + reg-names = "target_data", "rt", "scfg";
> + reg = <0x00 0x43600000 0x00 0x10000>,
> + <0x00 0x44880000 0x00 0x20000>,
> + <0x00 0x44860000 0x00 0x20000>;
> + /*
> + * Marked Disabled:
> + * Node is incomplete as it is meant for bootloaders and
> + * firmware on non-MPU processors
> + */
> + status = "disabled";
> + };
> +
> main_pmx0: pinctrl at f4000 {
> bootph-all;
> compatible = "pinctrl-single";
> @@ -101,6 +214,13 @@ main_pmx0: pinctrl at f4000 {
> pinctrl-single,function-mask = <0xffffffff>;
> };
>
> + main_esm: esm at 420000 {
> + bootph-pre-ram;
> + compatible = "ti,j721e-esm";
> + reg = <0x00 0x420000 0x00 0x1000>;
> + ti,esm-pins = <160>, <161>, <162>, <163>, <177>, <178>;
> + };
> +
> main_timer0: timer at 2400000 {
> bootph-all;
> compatible = "ti,am654-timer";
> @@ -114,6 +234,90 @@ main_timer0: timer at 2400000 {
> ti,timer-pwm;
> };
>
> + main_timer1: timer at 2410000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x2410000 0x00 0x400>;
> + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&k3_clks 37 2>;
> + clock-names = "fck";
> + assigned-clocks = <&k3_clks 37 2>;
> + assigned-clock-parents = <&k3_clks 37 3>;
> + power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + };
> +
> + main_timer2: timer at 2420000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x2420000 0x00 0x400>;
> + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&k3_clks 38 2>;
> + clock-names = "fck";
> + assigned-clocks = <&k3_clks 38 2>;
> + assigned-clock-parents = <&k3_clks 38 3>;
> + power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + };
> +
> + main_timer3: timer at 2430000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x2430000 0x00 0x400>;
> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&k3_clks 39 2>;
> + clock-names = "fck";
> + assigned-clocks = <&k3_clks 39 2>;
> + assigned-clock-parents = <&k3_clks 39 3>;
> + power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + };
> +
> + main_timer4: timer at 2440000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x2440000 0x00 0x400>;
> + interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&k3_clks 40 2>;
> + clock-names = "fck";
> + assigned-clocks = <&k3_clks 40 2>;
> + assigned-clock-parents = <&k3_clks 40 3>;
> + power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + };
> +
> + main_timer5: timer at 2450000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x2450000 0x00 0x400>;
> + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&k3_clks 41 2>;
> + clock-names = "fck";
> + assigned-clocks = <&k3_clks 41 2>;
> + assigned-clock-parents = <&k3_clks 41 3>;
> + power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + };
> +
> + main_timer6: timer at 2460000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x2460000 0x00 0x400>;
> + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&k3_clks 42 2>;
> + clock-names = "fck";
> + assigned-clocks = <&k3_clks 42 2>;
> + assigned-clock-parents = <&k3_clks 42 3>;
> + power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + };
> +
> + main_timer7: timer at 2470000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x2470000 0x00 0x400>;
> + interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&k3_clks 43 2>;
> + clock-names = "fck";
> + assigned-clocks = <&k3_clks 43 2>;
> + assigned-clock-parents = <&k3_clks 43 3>;
> + power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + };
> +
> main_uart0: serial at 2800000 {
> compatible = "ti,am64-uart", "ti,am654-uart";
> reg = <0x00 0x02800000 0x00 0x100>;
> @@ -133,4 +337,633 @@ main_uart1: serial at 2810000 {
> clock-names = "fclk";
> status = "disabled";
> };
> +
> + main_uart2: serial at 2820000 {
> + compatible = "ti,am64-uart", "ti,am654-uart";
> + reg = <0x00 0x02820000 0x00 0x100>;
> + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 153 0>;
> + clock-names = "fclk";
> + status = "disabled";
> + };
> +
> + main_uart3: serial at 2830000 {
> + compatible = "ti,am64-uart", "ti,am654-uart";
> + reg = <0x00 0x02830000 0x00 0x100>;
> + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 154 0>;
> + clock-names = "fclk";
> + status = "disabled";
> + };
> +
> + main_uart4: serial at 2840000 {
> + compatible = "ti,am64-uart", "ti,am654-uart";
> + reg = <0x00 0x02840000 0x00 0x100>;
> + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 155 0>;
> + clock-names = "fclk";
> + status = "disabled";
> + };
> +
> + main_uart5: serial at 2850000 {
> + compatible = "ti,am64-uart", "ti,am654-uart";
> + reg = <0x00 0x02850000 0x00 0x100>;
> + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 156 0>;
> + clock-names = "fclk";
> + status = "disabled";
> + };
> +
> + main_uart6: serial at 2860000 {
> + compatible = "ti,am64-uart", "ti,am654-uart";
> + reg = <0x00 0x02860000 0x00 0x100>;
> + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 158 0>;
> + clock-names = "fclk";
> + status = "disabled";
> + };
> +
> + main_i2c0: i2c at 20000000 {
> + compatible = "ti,am64-i2c", "ti,omap4-i2c";
> + reg = <0x00 0x20000000 0x00 0x100>;
> + interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 102 2>;
> + clock-names = "fck";
> + status = "disabled";
> + };
> +
> + main_i2c1: i2c at 20010000 {
> + compatible = "ti,am64-i2c", "ti,omap4-i2c";
> + reg = <0x00 0x20010000 0x00 0x100>;
> + interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 103 2>;
> + clock-names = "fck";
> + status = "disabled";
> + };
> +
> + main_i2c2: i2c at 20020000 {
> + compatible = "ti,am64-i2c", "ti,omap4-i2c";
> + reg = <0x00 0x20020000 0x00 0x100>;
> + interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 104 2>;
> + clock-names = "fck";
> + status = "disabled";
> + };
> +
> + main_i2c3: i2c at 20030000 {
> + compatible = "ti,am64-i2c", "ti,omap4-i2c";
> + reg = <0x00 0x20030000 0x00 0x100>;
> + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 105 2>;
> + clock-names = "fck";
> + status = "disabled";
> + };
> +
> + main_spi0: spi at 20100000 {
> + compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
> + reg = <0x00 0x20100000 0x00 0x400>;
> + interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 141 0>;
> + status = "disabled";
> + };
> +
> + main_spi1: spi at 20110000 {
> + compatible = "ti,am654-mcspi","ti,omap4-mcspi";
> + reg = <0x00 0x20110000 0x00 0x400>;
> + interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 142 0>;
> + status = "disabled";
> + };
> +
> + main_spi2: spi at 20120000 {
> + compatible = "ti,am654-mcspi","ti,omap4-mcspi";
> + reg = <0x00 0x20120000 0x00 0x400>;
> + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 143 0>;
> + status = "disabled";
> + };
> +
> + main_gpio_intr: interrupt-controller at a00000 {
> + compatible = "ti,sci-intr";
> + reg = <0x00 0x00a00000 0x00 0x800>;
> + ti,intr-trigger-type = <1>;
> + interrupt-controller;
> + interrupt-parent = <&gic500>;
> + #interrupt-cells = <1>;
> + ti,sci = <&dmsc>;
> + ti,sci-dev-id = <3>;
> + ti,interrupt-ranges = <0 32 16>;
> + };
> +
> + main_gpio0: gpio at 600000 {
> + compatible = "ti,am64-gpio", "ti,keystone-gpio";
> + reg = <0x0 0x00600000 0x0 0x100>;
reg = <0x00 0x00600000 0x0 0x100>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-parent = <&main_gpio_intr>;
> + interrupts = <190>, <191>, <192>,
> + <193>, <194>, <195>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + ti,ngpio = <92>;
> + ti,davinci-gpio-unbanked = <0>;
> + power-domains = <&k3_pds 77 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 77 0>;
> + clock-names = "gpio";
> + };
> +
> + main_gpio1: gpio at 601000 {
> + compatible = "ti,am64-gpio", "ti,keystone-gpio";
> + reg = <0x0 0x00601000 0x0 0x100>;
Same here
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-parent = <&main_gpio_intr>;
> + interrupts = <180>, <181>, <182>,
> + <183>, <184>, <185>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + ti,ngpio = <52>;
> + ti,davinci-gpio-unbanked = <0>;
> + power-domains = <&k3_pds 78 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 78 0>;
> + clock-names = "gpio";
> + };
> +
> + sdhci0: mmc at fa10000 {
> + compatible = "ti,am64-sdhci-8bit";
> + reg = <0x00 0x0fa10000 0x00 0x1000>, <0x00 0x0fa18000 0x00 0x400>;
> + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 57 1>, <&k3_clks 57 2>;
> + clock-names = "clk_ahb", "clk_xin";
> + assigned-clocks = <&k3_clks 57 2>;
> + assigned-clock-parents = <&k3_clks 57 4>;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + bus-width = <8>;
> + ti,clkbuf-sel = <0x7>;
> + ti,otap-del-sel-legacy = <0x0>;
> + ti,otap-del-sel-mmc-hs = <0x0>;
> + ti,otap-del-sel-ddr52 = <0x5>;
> + ti,otap-del-sel-hs200 = <0x5>;
> + ti,itap-del-sel-legacy = <0xa>;
> + ti,itap-del-sel-mmc-hs = <0x1>;
> + ti,otap-del-sel-hs400 = <0x5>;
> + ti,strobe-sel = <0x77>;
Do we have prelim datasheet? Are these values derived from such a source?
> + ti,trm-icp = <0x8>;
> + status = "disabled";
> + };
> +
> + sdhci1: mmc at fa00000 {
> + compatible = "ti,am62-sdhci";
> + reg = <0x00 0x0fa00000 0x00 0x1000>, <0x00 0x0fa08000 0x00 0x400>;
> + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 58 5>, <&k3_clks 58 6>;
> + clock-names = "clk_ahb", "clk_xin";
> + ti,trm-icp = <0x2>;
> + ti,otap-del-sel-legacy = <0x8>;
> + ti,otap-del-sel-sd-hs = <0x0>;
> + ti,otap-del-sel-sdr12 = <0x0>;
> + ti,otap-del-sel-sdr25 = <0x0>;
> + ti,otap-del-sel-sdr50 = <0x8>;
> + ti,otap-del-sel-sdr104 = <0x7>;
> + ti,otap-del-sel-ddr50 = <0x4>;
> + ti,itap-del-sel-legacy = <0xa>;
> + ti,itap-del-sel-sd-hs = <0x1>;
> + ti,itap-del-sel-sdr12 = <0xa>;
> + ti,itap-del-sel-sdr25 = <0x1>;
> + ti,clkbuf-sel = <0x7>;
> + bus-width = <4>;
> + status = "disabled";
> + };
> +
> + sdhci2: mmc at fa20000 {
> + compatible = "ti,am62-sdhci";
> + reg = <0x00 0x0fa20000 0x00 0x1000>, <0x00 0x0fa28000 0x00 0x400>;
> + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 184 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 184 5>, <&k3_clks 184 6>;
> + clock-names = "clk_ahb", "clk_xin";
> + ti,trm-icp = <0x2>;
> + ti,otap-del-sel-legacy = <0x8>;
> + ti,otap-del-sel-sd-hs = <0x0>;
> + ti,otap-del-sel-sdr12 = <0x0>;
> + ti,otap-del-sel-sdr25 = <0x0>;
> + ti,otap-del-sel-sdr50 = <0x8>;
> + ti,otap-del-sel-sdr104 = <0x7>;
> + ti,otap-del-sel-ddr50 = <0x8>;
> + ti,itap-del-sel-legacy = <0xa>;
> + ti,itap-del-sel-sd-hs = <0xa>;
> + ti,itap-del-sel-sdr12 = <0xa>;
> + ti,itap-del-sel-sdr25 = <0x1>;
> + ti,clkbuf-sel = <0x7>;
> + status = "disabled";
> + };
> +
> + usbss0: dwc3-usb at f900000 {
> + compatible = "ti,am62-usb";
> + reg = <0x00 0x0f900000 0x00 0x800>;
> + clocks = <&k3_clks 161 3>;
> + clock-names = "ref";
> + ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
> + ranges;
> + status = "disabled";
> +
> + usb0: usb at 31000000 {
> + compatible = "snps,dwc3";
> + reg = <0x00 0x31000000 0x00 0x50000>;
> + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
> + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
> + interrupt-names = "host", "peripheral";
> + maximum-speed = "high-speed";
> + dr_mode = "otg";
> + };
> + };
> +
> + usbss1: dwc3-usb at f910000 {
> + compatible = "ti,am62-usb";
> + reg = <0x00 0x0f910000 0x00 0x800>;
> + clocks = <&k3_clks 162 3>;
> + clock-names = "ref";
> + ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
wkup_conf is no longer a syscon node. Does this still work?
> + #address-cells = <2>;
> + #size-cells = <2>;
> + power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
> + ranges;
> + status = "disabled";
> +
> + usb1: usb at 31100000 {
> + compatible = "snps,dwc3";
> + reg = <0x00 0x31100000 0x00 0x50000>;
> + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
> + <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
> + interrupt-names = "host", "peripheral";
> + maximum-speed = "high-speed";
> + dr_mode = "otg";
> + };
> + };
> +
> + fss: bus at fc00000 {
> + compatible = "simple-bus";
> + reg = <0x00 0x0fc00000 0x00 0x70000>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + ospi0: spi at fc40000 {
> + compatible = "ti,am654-ospi", "cdns,qspi-nor";
> + reg = <0x00 0x0fc40000 0x00 0x100>,
> + <0x05 0x00000000 0x01 0x00000000>;
> + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
> + cdns,fifo-depth = <256>;
> + cdns,fifo-width = <4>;
> + cdns,trigger-address = <0x0>;
> + clocks = <&k3_clks 75 7>;
> + assigned-clocks = <&k3_clks 75 7>;
> + assigned-clock-parents = <&k3_clks 75 8>;
> + assigned-clock-rates = <166666666>;
> + power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> + };
> +
> + cpsw3g: ethernet at 8000000 {
> + compatible = "ti,am642-cpsw-nuss";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + reg = <0x00 0x08000000 0x00 0x200000>;
> + reg-names = "cpsw_nuss";
> + ranges = <0x00 0x00 0x00 0x08000000 0x00 0x200000>;
> + clocks = <&k3_clks 13 0>;
> + assigned-clocks = <&k3_clks 13 3>;
> + assigned-clock-parents = <&k3_clks 13 11>;
> + clock-names = "fck";
> + power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
> +
> + dmas = <&main_pktdma 0xc600 15>,
> + <&main_pktdma 0xc601 15>,
> + <&main_pktdma 0xc602 15>,
> + <&main_pktdma 0xc603 15>,
> + <&main_pktdma 0xc604 15>,
> + <&main_pktdma 0xc605 15>,
> + <&main_pktdma 0xc606 15>,
> + <&main_pktdma 0xc607 15>,
> + <&main_pktdma 0x4600 15>;
> + dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6",
> + "tx7", "rx";
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpsw_port1: port at 1 {
> + reg = <1>;
> + ti,mac-only;
> + label = "port1";
> + phys = <&phy_gmii_sel 1>;
> + mac-address = [00 00 00 00 00 00];
> + ti,syscon-efuse = <&wkup_conf 0x200>;
Same here
> + };
> +
> + cpsw_port2: port at 2 {
> + reg = <2>;
> + ti,mac-only;
> + label = "port2";
> + phys = <&phy_gmii_sel 2>;
> + mac-address = [00 00 00 00 00 00];
> + };
> + };
> +
> + cpsw3g_mdio: mdio at f00 {
> + compatible = "ti,cpsw-mdio","ti,davinci_mdio";
> + reg = <0x00 0xf00 0x00 0x100>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&k3_clks 13 0>;
> + clock-names = "fck";
> + bus_freq = <1000000>;
> + status = "disabled";
> + };
> +
> + cpts at 3d000 {
> + compatible = "ti,j721e-cpts";
> + reg = <0x00 0x3d000 0x00 0x400>;
> + clocks = <&k3_clks 13 3>;
> + clock-names = "cpts";
> + interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "cpts";
> + ti,cpts-ext-ts-inputs = <4>;
> + ti,cpts-periodic-outputs = <2>;
> + };
> + };
> +
> + hwspinlock: spinlock at 2a000000 {
> + compatible = "ti,am64-hwspinlock";
> + reg = <0x00 0x2a000000 0x00 0x1000>;
> + #hwlock-cells = <1>;
> + };
> +
> + mailbox0_cluster0: mailbox at 29000000 {
> + compatible = "ti,am64-mailbox";
> + reg = <0x00 0x29000000 0x00 0x200>;
> + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <1>;
> + ti,mbox-num-users = <4>;
> + ti,mbox-num-fifos = <16>;
> + };
> +
> + mailbox0_cluster1: mailbox at 29010000 {
> + compatible = "ti,am64-mailbox";
> + reg = <0x00 0x29010000 0x00 0x200>;
> + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <1>;
> + ti,mbox-num-users = <4>;
> + ti,mbox-num-fifos = <16>;
> + };
> +
> + mailbox0_cluster2: mailbox at 29020000 {
> + compatible = "ti,am64-mailbox";
> + reg = <0x00 0x29020000 0x00 0x200>;
> + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <1>;
> + ti,mbox-num-users = <4>;
> + ti,mbox-num-fifos = <16>;
> + };
> +
> + mailbox0_cluster3: mailbox at 29030000 {
> + compatible = "ti,am64-mailbox";
> + reg = <0x00 0x29030000 0x00 0x200>;
> + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <1>;
> + ti,mbox-num-users = <4>;
> + ti,mbox-num-fifos = <16>;
> + };
> +
> + ecap0: pwm at 23100000 {
> + compatible = "ti,am3352-ecap";
> + #pwm-cells = <3>;
> + reg = <0x00 0x23100000 0x00 0x100>;
> + power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 51 0>;
> + clock-names = "fck";
> + status = "disabled";
> + };
> +
> + ecap1: pwm at 23110000 {
> + compatible = "ti,am3352-ecap";
> + #pwm-cells = <3>;
> + reg = <0x00 0x23110000 0x00 0x100>;
> + power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 52 0>;
> + clock-names = "fck";
> + status = "disabled";
> + };
> +
> + ecap2: pwm at 23120000 {
> + compatible = "ti,am3352-ecap";
> + #pwm-cells = <3>;
> + reg = <0x00 0x23120000 0x00 0x100>;
> + power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 53 0>;
> + clock-names = "fck";
> + status = "disabled";
> + };
> +
> + main_mcan0: can at 20701000 {
> + compatible = "bosch,m_can";
> + reg = <0x00 0x20701000 0x00 0x200>,
> + <0x00 0x20708000 0x00 0x8000>;
> + reg-names = "m_can", "message_ram";
> + power-domains = <&k3_pds 98 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 98 6>, <&k3_clks 98 1>;
> + clock-names = "hclk", "cclk";
> + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "int0", "int1";
> + bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
> + status = "disabled";
> + };
> +
> + main_mcan1: can at 20711000 {
> + compatible = "bosch,m_can";
> + reg = <0x00 0x20711000 0x00 0x200>,
> + <0x00 0x20718000 0x00 0x8000>;
> + reg-names = "m_can", "message_ram";
> + power-domains = <&k3_pds 99 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 99 6>, <&k3_clks 99 1>;
> + clock-names = "hclk", "cclk";
> + interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "int0", "int1";
> + bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
> + status = "disabled";
> + };
> +
> + main_rti0: watchdog at e000000 {
> + compatible = "ti,j7-rti-wdt";
> + reg = <0x00 0x0e000000 0x00 0x100>;
> + clocks = <&k3_clks 125 0>;
> + power-domains = <&k3_pds 125 TI_SCI_PD_EXCLUSIVE>;
> + assigned-clocks = <&k3_clks 125 0>;
> + assigned-clock-parents = <&k3_clks 125 2>;
> + };
> +
> + main_rti1: watchdog at e010000 {
> + compatible = "ti,j7-rti-wdt";
> + reg = <0x00 0x0e010000 0x00 0x100>;
> + clocks = <&k3_clks 126 0>;
> + power-domains = <&k3_pds 126 TI_SCI_PD_EXCLUSIVE>;
> + assigned-clocks = <&k3_clks 126 0>;
> + assigned-clock-parents = <&k3_clks 126 2>;
> + };
> +
> + main_rti2: watchdog at e020000 {
> + compatible = "ti,j7-rti-wdt";
> + reg = <0x00 0x0e020000 0x00 0x100>;
> + clocks = <&k3_clks 127 0>;
> + power-domains = <&k3_pds 127 TI_SCI_PD_EXCLUSIVE>;
> + assigned-clocks = <&k3_clks 127 0>;
> + assigned-clock-parents = <&k3_clks 127 2>;
> + };
> +
> + main_rti3: watchdog at e030000 {
> + compatible = "ti,j7-rti-wdt";
> + reg = <0x00 0x0e030000 0x00 0x100>;
> + clocks = <&k3_clks 128 0>;
> + power-domains = <&k3_pds 128 TI_SCI_PD_EXCLUSIVE>;
> + assigned-clocks = <&k3_clks 128 0>;
> + assigned-clock-parents = <&k3_clks 128 2>;
> + };
> +
> + main_rti15: watchdog at e0f0000 {
> + compatible = "ti,j7-rti-wdt";
> + reg = <0x00 0x0e0f0000 0x00 0x100>;
> + clocks = <&k3_clks 130 0>;
> + power-domains = <&k3_pds 130 TI_SCI_PD_EXCLUSIVE>;
> + assigned-clocks = <&k3_clks 130 0>;
> + assigned-clock-parents = <&k3_clks 130 2>;
> + };
> +
> + epwm0: pwm at 23000000 {
> + compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
> + #pwm-cells = <3>;
> + reg = <0x00 0x23000000 0x00 0x100>;
> + power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>;
> + clock-names = "tbclk", "fck";
> + status = "disabled";
> + };
> +
> + epwm1: pwm at 23010000 {
> + compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
> + #pwm-cells = <3>;
> + reg = <0x00 0x23010000 0x00 0x100>;
> + power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>;
> + clock-names = "tbclk", "fck";
> + status = "disabled";
> + };
> +
> + epwm2: pwm at 23020000 {
> + compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
> + #pwm-cells = <3>;
> + reg = <0x00 0x23020000 0x00 0x100>;
> + power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>;
> + clock-names = "tbclk", "fck";
> + status = "disabled";
> + };
> +
> + mcasp0: audio-controller at 2b00000 {
> + compatible = "ti,am33xx-mcasp-audio";
> + reg = <0x00 0x02b00000 0x00 0x2000>,
> + <0x00 0x02b08000 0x00 0x400>;
> + reg-names = "mpu", "dat";
> + interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "tx", "rx";
> +
> + dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
> + dma-names = "tx", "rx";
> +
> + clocks = <&k3_clks 190 0>;
> + clock-names = "fck";
> + assigned-clocks = <&k3_clks 190 0>;
> + assigned-clock-parents = <&k3_clks 190 2>;
> + power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
> + status = "disabled";
> + };
> +
> + mcasp1: audio-controller at 2b10000 {
> + compatible = "ti,am33xx-mcasp-audio";
> + reg = <0x00 0x02b10000 0x00 0x2000>,
> + <0x00 0x02b18000 0x00 0x400>;
> + reg-names = "mpu", "dat";
> + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "tx", "rx";
> +
> + dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
> + dma-names = "tx", "rx";
> +
> + clocks = <&k3_clks 191 0>;
> + clock-names = "fck";
> + assigned-clocks = <&k3_clks 191 0>;
> + assigned-clock-parents = <&k3_clks 191 2>;
> + power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
> + status = "disabled";
> + };
> +
> + mcasp2: audio-controller at 2b20000 {
> + compatible = "ti,am33xx-mcasp-audio";
> + reg = <0x00 0x02b20000 0x00 0x2000>,
> + <0x00 0x02b28000 0x00 0x400>;
> + reg-names = "mpu", "dat";
> + interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "tx", "rx";
> +
> + dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
> + dma-names = "tx", "rx";
> +
> + clocks = <&k3_clks 192 0>;
> + clock-names = "fck";
> + assigned-clocks = <&k3_clks 192 0>;
> + assigned-clock-parents = <&k3_clks 192 2>;
> + power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
> + status = "disabled";
> + };
> };
> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi
> index 27ca1c9c6d135..edf5841f0becd 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi
> @@ -5,11 +5,202 @@
> */
>
> &cbass_mcu {
> + bootph-all;
> +
> mcu_pmx0: pinctrl at 4084000 {
> + bootph-all;
> compatible = "pinctrl-single";
> reg = <0x00 0x04084000 0x00 0x88>;
> #pinctrl-cells = <1>;
> pinctrl-single,register-width = <32>;
> pinctrl-single,function-mask = <0xffffffff>;
> };
> +
> + mcu_esm: esm at 4100000 {
> + bootph-pre-ram;
> + compatible = "ti,j721e-esm";
> + reg = <0x00 0x4100000 0x00 0x1000>;
> + ti,esm-pins = <0>, <1>, <2>, <85>;
Do we want to keep it reserved by default as this maybe under MCU FW control?
> + };
> +
> + /*
> + * The MCU domain timer interrupts are routed only to the ESM module,
> + * and not currently available for Linux. The MCU domain timers are
> + * of limited use without interrupts, and likely reserved by the ESM.
> + */
> + mcu_timer0: timer at 4800000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x4800000 0x00 0x400>;
> + clocks = <&k3_clks 35 2>;
> + clock-names = "fck";
> + power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + status = "reserved";
> + };
> +
> + mcu_timer1: timer at 4810000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x4810000 0x00 0x400>;
> + clocks = <&k3_clks 48 2>;
> + clock-names = "fck";
> + power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + status = "reserved";
> + };
> +
> + mcu_timer2: timer at 4820000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x4820000 0x00 0x400>;
> + clocks = <&k3_clks 49 2>;
> + clock-names = "fck";
> + power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + status = "reserved";
> + };
> +
> + mcu_timer3: timer at 4830000 {
> + compatible = "ti,am654-timer";
> + reg = <0x00 0x4830000 0x00 0x400>;
> + clocks = <&k3_clks 50 2>;
> + clock-names = "fck";
> + power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>;
> + ti,timer-pwm;
> + status = "reserved";
> + };
> +
> + mcu_uart0: serial at 4a00000 {
> + compatible = "ti,am64-uart", "ti,am654-uart";
> + reg = <0x00 0x04a00000 0x00 0x100>;
> + interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 149 0>;
> + clock-names = "fclk";
> + status = "disabled";
> + };
> +
> + mcu_i2c0: i2c at 4900000 {
> + compatible = "ti,am64-i2c", "ti,omap4-i2c";
> + reg = <0x00 0x04900000 0x00 0x100>;
> + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 106 2>;
> + clock-names = "fck";
> + status = "disabled";
> + };
> +
> + mcu_spi0: spi at 4b00000 {
> + compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
> + reg = <0x00 0x04b00000 0x00 0x400>;
> + interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 147 0>;
> + status = "disabled";
> + };
> +
> + mcu_spi1: spi at 4b10000 {
> + compatible = "ti,am654-mcspi","ti,omap4-mcspi";
> + reg = <0x00 0x04b10000 0x00 0x400>;
> + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 148 0>;
> + status = "disabled";
> + };
> +
> + mcu_gpio_intr: interrupt-controller at 4210000 {
> + compatible = "ti,sci-intr";
> + reg = <0x00 0x04210000 0x00 0x200>;
> + ti,intr-trigger-type = <1>;
> + interrupt-controller;
> + interrupt-parent = <&gic500>;
> + #interrupt-cells = <1>;
> + ti,sci = <&dmsc>;
> + ti,sci-dev-id = <5>;
> + ti,interrupt-ranges = <0 104 4>;
> + };
> +
> + mcu_gpio0: gpio at 4201000 {
> + compatible = "ti,am64-gpio", "ti,keystone-gpio";
> + reg = <0x00 0x4201000 0x00 0x100>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-parent = <&mcu_gpio_intr>;
> + interrupts = <30>, <31>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + ti,ngpio = <24>;
> + ti,davinci-gpio-unbanked = <0>;
> + power-domains = <&k3_pds 79 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 79 0>;
> + clock-names = "gpio";
> + };
> +
> + mcu_rti0: watchdog at 4880000 {
> + compatible = "ti,j7-rti-wdt";
> + reg = <0x00 0x04880000 0x00 0x100>;
> + clocks = <&k3_clks 131 0>;
> + power-domains = <&k3_pds 131 TI_SCI_PD_EXCLUSIVE>;
> + assigned-clocks = <&k3_clks 131 0>;
> + assigned-clock-parents = <&k3_clks 131 2>;
> + /* Tightly coupled to M4F */
> + status = "reserved";
> + };
> +
> + mcu_mcan0: can at 4e08000 {
> + compatible = "bosch,m_can";
> + reg = <0x00 0x4e08000 0x00 0x200>,
> + <0x00 0x4e00000 0x00 0x8000>;
> + reg-names = "m_can", "message_ram";
> + power-domains = <&k3_pds 188 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 188 6>, <&k3_clks 188 1>;
> + clock-names = "hclk", "cclk";
> + bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
> + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "int0", "int1";
> + status = "disabled";
> + };
> +
> + mcu_mcan1: can at 4e18000 {
> + compatible = "bosch,m_can";
> + reg = <0x00 0x4e18000 0x00 0x200>,
> + <0x00 0x4e10000 0x00 0x8000>;
> + reg-names = "m_can", "message_ram";
> + power-domains = <&k3_pds 189 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 189 6>, <&k3_clks 189 1>;
> + clock-names = "hclk", "cclk";
> + bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
> + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "int0", "int1";
> + status = "disabled";
> + };
> +
> + mcu_r5fss0: r5fss at 79000000 {
> + compatible = "ti,am62-r5fss";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x79000000 0x00 0x79000000 0x8000>,
> + <0x79020000 0x00 0x79020000 0x8000>;
> + power-domains = <&k3_pds 7 TI_SCI_PD_EXCLUSIVE>;
> + mcu_r5fss0_core0: r5f at 79000000 {
> + compatible = "ti,am62-r5f";
> + reg = <0x79000000 0x00008000>,
> + <0x79020000 0x00008000>;
> + reg-names = "atcm", "btcm";
> + ti,sci = <&dmsc>;
> + ti,sci-dev-id = <9>;
> + ti,sci-proc-ids = <0x03 0xff>;
> + resets = <&k3_reset 9 1>;
> + firmware-name = "am62p-mcu-r5f0_0-fw";
> + ti,atcm-enable = <0>;
> + ti,btcm-enable = <1>;
> + ti,loczrama = <0>;
> + };
> + };
> };
> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi
> new file mode 100644
> index 0000000000000..85ce545633ea5
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi
> @@ -0,0 +1,47 @@
> +// SPDX-License-Identifier: GPL-2.0
> +
> +#include <dt-bindings/thermal/thermal.h>
> +
> +thermal_zones: thermal-zones {
> + main0_thermal: main0-thermal {
> + polling-delay-passive = <250>; /* milliSeconds */
> + polling-delay = <500>; /* milliSeconds */
> + thermal-sensors = <&wkup_vtm0 0>;
> +
> + trips {
> + main0_crit: main0-crit {
> + temperature = <125000>; /* milliCelsius */
> + hysteresis = <2000>; /* milliCelsius */
> + type = "critical";
> + };
> + };
> + };
> +
> + main1_thermal: main1-thermal {
> + polling-delay-passive = <250>; /* milliSeconds */
> + polling-delay = <500>; /* milliSeconds */
> + thermal-sensors = <&wkup_vtm0 1>;
> +
> + trips {
> + main1_crit: main1-crit {
> + temperature = <125000>; /* milliCelsius */
> + hysteresis = <2000>; /* milliCelsius */
> + type = "critical";
> + };
> + };
> + };
> +
> + main2_thermal: main2-thermal {
> + polling-delay-passive = <250>; /* milliSeconds */
> + polling-delay = <500>; /* milliSeconds */
> + thermal-sensors = <&wkup_vtm0 2>;
> +
> + trips {
> + main2_crit: main2-crit {
> + temperature = <125000>; /* milliCelsius */
> + hysteresis = <2000>; /* milliCelsius */
> + type = "critical";
> + };
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> index aaf4b793b58e7..6b36cd409d758 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> @@ -5,6 +5,8 @@
> */
>
> &cbass_wakeup {
> + bootph-all;
> +
> wkup_conf: bus at 43000000 {
> bootph-all;
> compatible = "simple-bus";
> @@ -29,4 +31,69 @@ wkup_uart0: serial at 2b300000 {
> clock-names = "fclk";
> status = "disabled";
> };
> +
> + wkup_i2c0: i2c at 2b200000 {
> + compatible = "ti,am64-i2c", "ti,omap4-i2c";
> + reg = <0x00 0x2b200000 0x00 0x100>;
> + interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 107 4>;
> + clock-names = "fck";
> + status = "disabled";
> + };
> +
> + wkup_rtc0: rtc at 2b1f0000 {
> + compatible = "ti,am62-rtc";
> + reg = <0x00 0x2b1f0000 0x00 0x100>;
> + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&k3_clks 117 6> , <&k3_clks 117 0>;
> + clock-names = "vbus", "osc32k";
> + power-domains = <&k3_pds 117 TI_SCI_PD_EXCLUSIVE>;
> + wakeup-source;
> + };
> +
> + wkup_rti0: watchdog at 2b000000 {
> + compatible = "ti,j7-rti-wdt";
> + reg = <0x00 0x2b000000 0x00 0x100>;
> + clocks = <&k3_clks 132 0>;
> + power-domains = <&k3_pds 132 TI_SCI_PD_EXCLUSIVE>;
> + assigned-clocks = <&k3_clks 132 0>;
> + assigned-clock-parents = <&k3_clks 132 2>;
> + /* Used by DM firmware */
> + status = "reserved";
> + };
> +
> + wkup_vtm0: temperature-sensor at b00000 {
> + compatible = "ti,j7200-vtm";
> + reg = <0x00 0xb00000 0x00 0x400>,
> + <0x00 0xb01000 0x00 0x400>;
> + power-domains = <&k3_pds 95 TI_SCI_PD_EXCLUSIVE>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + wkup_r5fss0: r5fss at 78000000 {
> + compatible = "ti,am62-r5fss";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x78000000 0x00 0x78000000 0x8000>,
> + <0x78100000 0x00 0x78100000 0x8000>;
> + power-domains = <&k3_pds 119 TI_SCI_PD_EXCLUSIVE>;
> +
> + wkup_r5fss0_core0: r5f at 78000000 {
> + compatible = "ti,am62-r5f";
> + reg = <0x78000000 0x00008000>,
> + <0x78100000 0x00008000>;
> + reg-names = "atcm", "btcm";
> + ti,sci = <&dmsc>;
> + ti,sci-dev-id = <121>;
> + ti,sci-proc-ids = <0x01 0xff>;
> + resets = <&k3_reset 121 1>;
> + firmware-name = "am62-wkup-r5f0_0-fw";
> + ti,atcm-enable = <1>;
> + ti,btcm-enable = <1>;
> + ti,loczrama = <1>;
> + };
> + };
> };
> diff --git a/arch/arm64/boot/dts/ti/k3-am62p.dtsi b/arch/arm64/boot/dts/ti/k3-am62p.dtsi
> index 294ab73ec98b7..c6c2c2e9e9858 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62p.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62p.dtsi
> @@ -114,6 +114,8 @@ cbass_wakeup: bus at b00000 {
> <0x00 0x78100000 0x00 0x78100000 0x00 0x00008000>; /* DM R5 BTCM*/
> };
> };
> +
> + #include "k3-am62p-thermal.dtsi"
> };
>
> /* Now include peripherals for each bus segment */
--
Regards
Vignesh
More information about the linux-arm-kernel
mailing list