[PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC

[Marek Vasut]

On 10/11/23 04:12, Shawn Guo wrote:
> On Tue, Oct 10, 2023 at 03:42:14PM +0200, Marek Vasut wrote:
>> On 10/10/23 02:58, Shawn Guo wrote:
>>> On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote:
>>>> On 10/9/23 14:36, Shawn Guo wrote:
>>>>> On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote:
>>>>>> On 9/24/23 16:21, Shawn Guo wrote:
>>>>>>> On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote:
>>>>>>>> Describe VDD_ARM (BUCK2) run and standby voltage in DT.
>>>>>>>>
>>>>>>>> Signed-off-by: Marek Vasut <marex at denx.de>
>>>>>>>> ---
>>>>>>>> Cc: Conor Dooley <conor+dt at kernel.org>
>>>>>>>> Cc: Fabio Estevam <festevam at gmail.com>
>>>>>>>> Cc: Frieder Schrempf <frieder.schrempf at kontron.de>
>>>>>>>> Cc: Geert Uytterhoeven <geert+renesas at glider.be>
>>>>>>>> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt at linaro.org>
>>>>>>>> Cc: Magnus Damm <magnus.damm at gmail.com>
>>>>>>>> Cc: Marek Vasut <marex at denx.de>
>>>>>>>> Cc: NXP Linux Team <linux-imx at nxp.com>
>>>>>>>> Cc: Peng Fan <peng.fan at nxp.com>
>>>>>>>> Cc: Pengutronix Kernel Team <kernel at pengutronix.de>
>>>>>>>> Cc: Rob Herring <robh+dt at kernel.org>
>>>>>>>> Cc: Sascha Hauer <s.hauer at pengutronix.de>
>>>>>>>> Cc: Shawn Guo <shawnguo at kernel.org>
>>>>>>>> Cc: devicetree at vger.kernel.org
>>>>>>>> Cc: linux-arm-kernel at lists.infradead.org
>>>>>>>> ---
>>>>>>>>      arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++
>>>>>>>>      1 file changed, 2 insertions(+)
>>>>>>>>
>>>>>>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts
>>>>>>>> index 13674dc64be9d..d98a040860a48 100644
>>>>>>>> --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts
>>>>>>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts
>>>>>>>> @@ -362,6 +362,8 @@ buck1: BUCK1 {	/* VDD_SOC (dual-phase with BUCK3) */
>>>>>>>>      			};
>>>>>>>>      			buck2: BUCK2 {	/* VDD_ARM */
>>>>>>>> +				nxp,dvs-run-voltage = <950000>;
>>>>>>>> +				nxp,dvs-standby-voltage = <850000>;
>>>>>>>
>>>>>>> Buck2 is not turned off in DSM on i.MX8MP?
>>>>>>
>>>>>> It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN .
>>>>>
>>>>> Right.  But nxp,dvs-standby-voltage specifies the voltage when PMIC
>>>>> is in STANDBY mode.  My understanding is that the SoC will be in SUSPEND
>>>>> state while PMIC is in STANDBY mode.
>>>>
>>>> I agree
>>>>
>>>>> Is it possible that the SoC in
>>>>> IDLE/RUN while PMIC is in STANDBY mode at all?
>>>>
>>>> No, I don't think so, but there's still the PMIC part:
>>>>
>>>> https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf
>>>>
>>>> 7.3.7 STANDBY mode
>>>> "
>>>> PCA9450 transitions to STANDBY mode from RUN mode when
>>>> both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1
>>>> and BUCK3 output voltage is set to BUCK1OUT_DVS1 and
>>>> BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit
>>>> in each BUCKx_CTRL register is configured to 1.
>>>> "
>>>>
>>>> Specifically
>>>> "
>>>> BUCK2 are turned off when DVS_CTRL bit in each
>>>> BUCKx_CTRL register is configured to 1.
>>>> "
>>>>
>>>> 8.2.19 0x13 BUCK2CTRL
>>>> "
>>>> 4
>>>> DVS_CTRL
>>>> DVS Control configuration
>>>> 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of
>>>> PMIC_STBY_REQ
>>>> 1b = DVS control through PMIC_STBY_REQ
>>>> "
>>>>
>>>> Notice that the reset-default is '0b' , so unless the PMIC is reconfigured,
>>>> the BUCK2 will stay powered on even in STANDBY/SUSPEND.
>>>
>>> Hmm, isn't B2_ENMODE controlling on/off of BUCK2?
>>>
>>> BUCK2 enable mode
>>> 00b = OFF
>>> 01b = ON by PMIC_ON_REQ = H
>>> 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default)
>>> 11b = Always ON
>>>
>>> So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ
>>> goes high, right?
>>
>> I think so.
>>
>> But since the buck2 in DVS behavior is user-configurable, and this can be
>> configured by the bootloader, I would say that it is a good idea to keep the
>> buck2 DVS value defined in the DT, rather than keep it undefined.
>>
>> Also note that this board is a development kit, so we just don't know what
>> users might do with it.
> 
> Honestly, I just do not see any reason why one would change the most
> power efficient default configuration to something consuming much more
> power.
> 
> Also, even if DVS control is enabled, 0.85 V is already the target
> voltage for STANDBY mode by default.
> 
> Bottom line is that we should have some comment on this change, because
> it makes eDM SBC so unique among all those PCA9450 based boards and
> makes people like me wonder why eDM SBC board needs this setting.

This is definitely not unique, a lot of i.MX8MP boards configure both 
run and standby voltage for buck2 as well, even the NXP EVK does:

next-20231011$ git grep -l dvs-standby-voltage 
arch/arm64/boot/dts/freescale/imx8mp*
arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi
arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
arch/arm64/boot/dts/freescale/imx8mp-evk.dts
arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi
arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi
arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts
arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi

So, can this patch go in as-is or do you want additional comment in V2?