[PATCH v3 2/3] arm64: dts: ti: Add overlay for NAND daughter card

[Krzysztof Kozlowski]

On 05/10/2023 11:37, Nitin Yadav wrote:
> Introduce k3-am62-lp-sk-nand.dtso overlay file to support
> the X8 NAND EXPANSION BOARD card (PROC143E1) for AM62x LP SK
> board. NAND has partitions for different boot components as
> below:
> 
> 0x000000000000-0x000000200000 : "NAND.tiboot3
> 0x000000200000-0x000000400000 : "NAND.tispl
> 0x000000400000-0x000000600000 : "NAND.tiboot3.backup
> 0x000000600000-0x000000a00000 : "NAND.u-boot
> 0x000000a00000-0x000000a40000 : "NAND.u-boot-env
> 0x000000a40000-0x000000a80000 : "NAND.u-boot-env.backup
> 0x000000a80000-0x000040000000 : "NAND.file-system
> 
> Disable mcasp1 node in DT to avoid pinmux conflict. Update
> Makefile to include k3-am62-lp-sk-nand.dtso.
> 
> Signed-off-by: Nitin Yadav <n-yadav at ti.com>
> Reviewed-by: Roger Quadros <rogerq at kernel.org>
> ---
>  arch/arm64/boot/dts/ti/Makefile               |   3 +-
>  .../arm64/boot/dts/ti/k3-am62-lp-sk-nand.dtso | 119 ++++++++++++++++++
>  2 files changed, 121 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am62-lp-sk-nand.dtso
> 
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index b3516419f95d..f6e3ff55f787 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -18,7 +18,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-yavia.dtb
>  dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dahlia.dtb
>  dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dev.dtb
>  dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-yavia.dtb
> -dtb-$(CONFIG_ARCH_K3) += k3-am62-lp-sk.dtb
> +k3-am62-lp-sk-nand-dtbs := k3-am62-lp-sk.dtb k3-am62-lp-sk-nand.dtbo
> +dtb-$(CONFIG_ARCH_K3) += k3-am62-lp-sk-nand.dtb
>  dtb-$(CONFIG_ARCH_K3) += k3-am62x-sk-hdmi-audio.dtbo
>  
>  # Boards with AM62Ax SoC
> diff --git a/arch/arm64/boot/dts/ti/k3-am62-lp-sk-nand.dtso b/arch/arm64/boot/dts/ti/k3-am62-lp-sk-nand.dtso
> new file mode 100644
> index 000000000000..0f4e26db534b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am62-lp-sk-nand.dtso
> @@ -0,0 +1,119 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +#include "k3-pinctrl.h"
> +
> +&mcasp1 {
> +	status = "disabled";
> +};
> +
> +&main_pmx0 {
> +	gpmc0_pins_default: gpmc0-pins-default {
> +		pinctrl-single,pins = <
> +			AM62X_IOPAD(0x003c, PIN_INPUT, 0) /* (M25) GPMC0_AD0 */
> +			AM62X_IOPAD(0x0040, PIN_INPUT, 0) /* (N23) GPMC0_AD1 */
> +			AM62X_IOPAD(0x0044, PIN_INPUT, 0) /* (N24) GPMC0_AD2 */
> +			AM62X_IOPAD(0x0048, PIN_INPUT, 0) /* (N25) GPMC0_AD3 */
> +			AM62X_IOPAD(0x004c, PIN_INPUT, 0) /* (P24) GPMC0_AD4 */
> +			AM62X_IOPAD(0x0050, PIN_INPUT, 0) /* (P22) GPMC0_AD5 */
> +			AM62X_IOPAD(0x0054, PIN_INPUT, 0) /* (P21) GPMC0_AD6 */
> +			AM62X_IOPAD(0x0058, PIN_INPUT, 0) /* (R23) GPMC0_AD7 */
> +			AM62X_IOPAD(0x0084, PIN_OUTPUT, 0) /* (L23) GPMC0_ADVn_ALE */
> +			AM62X_IOPAD(0x0088, PIN_OUTPUT, 0) /* (L24) GPMC0_OEn_REn */
> +			AM62X_IOPAD(0x008c, PIN_OUTPUT, 0) /* (L25) GPMC0_WEn */
> +			AM62X_IOPAD(0x0090, PIN_OUTPUT, 0) /* (M24) GPMC0_BE0n_CLE */
> +			AM62X_IOPAD(0x00a8, PIN_OUTPUT, 0) /* (M21) GPMC0_CSn0 */
> +			AM62X_IOPAD(0x0098, PIN_INPUT, 0) /* (U23) GPMC0_WAIT0 */
> +		>;
> +	};
> +};
> +
> +&gpmc0 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gpmc0_pins_default>;
> +	ranges = <0 0 0x00 0x51000000 0x01000000>; /* CS0 space. Min partition = 16MB */
> +	#address-cells = <2>;
> +	#size-cells = <1>;

You have these two in DTSI.

> +
> +	nand0_0: nand at 0,0 {
> +		compatible = "ti,am64-nand"

Best regards,
Krzysztof