[PATCH 1/2] arm64: dts: ti: k3-am62a: Enable UHS mode support for SD cards

[Judith Mendez]

On 10/26/23 2:01 AM, Nitin Yadav wrote:
> Hook up required IO voltage regulators to support UHS modes on
> SD cards.
> 
> Signed-off-by: Nitin Yadav <n-yadav at ti.com>
> ---
>   arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 20 ++++++++++++++++++++
>   1 file changed, 20 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> index 9f3dfbfbf369..3ae1ea1997a4 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> @@ -102,6 +102,19 @@ vdd_mmc1: regulator-3 {
>   		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
>   	};
>   
> +	vddshv_sdio: regulator-4 {
> +		compatible = "regulator-gpio";
> +		regulator-name = "vddshv_sdio";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vddshv_sdio_default_pins>;
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
> +		states = <1800000 0x0>,
> +			 <3300000 0x1>;
> +	};
> +
>   	leds {
>   		compatible = "gpio-leds";
>   		pinctrl-names = "default";
> @@ -189,6 +202,12 @@ AM62AX_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */
>   		>;
>   	};
>   
> +	vddshv_sdio_default_pins: vddshv-sdio-default-pins {
> +		pinctrl-single,pins = <
> +			AM62AX_IOPAD(0x07c, PIN_OUTPUT, 7) /* (M19) GPMC0_CLK.GPIO0_31 */

Isn't this ball name N22? I might be wrong, but I did check using 
SYSCONFIG tool and datasheet.

> +		>;
> +	};
> +
>   	main_mmc1_pins_default: main-mmc1-default-pins {
>   		pinctrl-single,pins = <
>   			AM62AX_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
> @@ -294,6 +313,7 @@ &sdhci1 {
>   	/* SD/MMC */
>   	status = "okay";
>   	vmmc-supply = <&vdd_mmc1>;
> +	vqmmc-supply = <&vddshv_sdio>;
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&main_mmc1_pins_default>;
>   	ti,driver-strength-ohm = <50>;