[PATCH v2 2/4] dt-bindings: pinctrl: Document nuvoton ma35d1 pin control

[Jacky Huang]

Dear Krzysztof,

Thanks for your review.


On 2023/11/28 下午 03:34, Krzysztof Kozlowski wrote:
> On 28/11/2023 07:11, Jacky Huang wrote:
>> From: Jacky Huang <ychuang3 at nuvoton.com>
>>
>> Add documentation to describe nuvoton ma35d1 pin control and GPIO.
>>
>> Signed-off-by: Jacky Huang <ychuang3 at nuvoton.com>
>> ---
> Your changelog said:
>
>>    - Remove ma35d1-pinfunc.h which is unused after update definition of
> 'nuvoton,pins'.
>
> You forgot to add:
>
> " - Do not test the bindings before sending"
>
> I assume none of the driver changes compile either.

It's my mistake. I forgot to remove 'ma35d1-pinfunc.h' from my local 
copy, and as a consequence, the 'dt_binding_check' did not catch this 
error. I will fix this.
>>   .../pinctrl/nuvoton,ma35d1-pinctrl.yaml       | 189 ++++++++++++++++++
>>   1 file changed, 189 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
>> new file mode 100644
>> index 000000000000..84287293a726
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
>> @@ -0,0 +1,189 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/nuvoton,ma35d1-pinctrl.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Nuvoton MA35D1 pin control and GPIO
>> +
>> +maintainers:
>> +  - Shan-Chun Hung <schung at nuvoton.com>
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - nuvoton,ma35d1-pinctrl
>> +
>> +  '#address-cells':
>> +    const: 1
>> +
>> +  '#size-cells':
>> +    const: 1
>> +
>> +  nuvoton,sys:
>> +    $ref: /schemas/types.yaml#/definitions/phandle
>> +    description:
>> +      phandle of the system-management node.
>> +
>> +  ranges: true
>> +
>> +allOf:
>> +  - $ref: pinctrl.yaml#
> allOf goes before additionalProperties.
>
>> +
>> +required:
>> +  - compatible
>> +  - nuvoton,sys
> This goes after patternProperties

I will fix the above two as:

allOf:
   - $ref: pinctrl.yaml#

required:
   - compatible
   - nuvoton,sys

additionalProperties: false

examples:



>> +
>> +patternProperties:
>> +  "^gpio@[0-9a-f]+$":
>> +    type: object
>> +    additionalProperties: false
>> +    properties:
>> +      gpio-controller: true
>> +
>> +      '#gpio-cells':
>> +        const: 2
>> +
>> +      reg:
>> +        maxItems: 1
>> +
>> +      clocks:
>> +        maxItems: 1
>> +
>> +      interrupt-controller: true
>> +
>> +      '#interrupt-cells':
>> +        const: 2
>> +
>> +      interrupts:
>> +        description:
>> +          The interrupt outputs to sysirq.
>> +        maxItems: 1
>> +
>> +    required:
>> +      - gpio-controller
>> +      - '#gpio-cells'
>> +      - reg
>> +      - clocks
>> +      - interrupt-controller
>> +      - '#interrupt-cells'
>> +      - interrupts
>> +
>> +  "^pin-[a-z0-9]+$":
>> +    type: object
>> +    description:
>> +      A pinctrl node should contain at least one subnodes representing the
>> +      pinctrl groups available on the machine. Each subnode will list the
>> +      pins it needs, and how they should be configured, with regard to muxer
>> +      configuration, pullups, drive strength, input enable/disable and input
>> +      schmitt.
>> +
>> +    allOf:
> Drop allOf, just $ref

OK, I will fix it.

>> +      - $ref: pincfg-node.yaml#
>> +
>> +    properties:
>> +      bias-disable: true
> Drop this and other "true", why do you need them here?

We are following the conventions used in other pinctrl documents, such as
'realtek,rtd1315e-pinctrl.yaml' and 'xlnx,zynqmp-pinctrl.yaml'.

After comparing various pinctrl documents, I noticed that they all express
it as 'bias-disable: true'. Therefore, may I keep the current format?

>> +
>> +      bias-pull-down: true
>> +
>> +      bias-pull-up: true
>> +
>> +      power-source:
>> +        description: |
>> +          Valid arguments are described as below:
>> +          0: power supply of 1.8V
>> +          1: power supply of 3.3V
>> +        enum: [0, 1]
>> +
>> +      drive-strength-microamp:
>> +        oneOf:
>> +          - enum: [ 2900, 4400, 5800, 7300, 8600, 10100, 11500, 13000 ]
>> +            description: 1.8V I/O driving strength
>> +          - enum: [ 17100, 25600, 34100, 42800, 48000, 56000, 77000, 82000 ]
>> +            description: 3.3V I/O driving strength
>> +
>> +      input-enable: true
>> +
>> +      input-schmitt-enable: true
>> +
>> +    unevaluatedProperties: false
>
>
> Best regards,
> Krzysztof
>


Best Regards,
Jacky Huang