[PATCH v2 12/14] arm64/mm: Wire up PTE_CONT for user mappings

[Alistair Popple]

Ryan Roberts <ryan.roberts at arm.com> writes:

[...]

> +static void contpte_fold(struct mm_struct *mm, unsigned long addr,
> +			pte_t *ptep, pte_t pte, bool fold)
> +{
> +	struct vm_area_struct vma = TLB_FLUSH_VMA(mm, 0);
> +	unsigned long start_addr;
> +	pte_t *start_ptep;
> +	int i;
> +
> +	start_ptep = ptep = contpte_align_down(ptep);
> +	start_addr = addr = ALIGN_DOWN(addr, CONT_PTE_SIZE);
> +	pte = pfn_pte(ALIGN_DOWN(pte_pfn(pte), CONT_PTES), pte_pgprot(pte));
> +	pte = fold ? pte_mkcont(pte) : pte_mknoncont(pte);
> +
> +	for (i = 0; i < CONT_PTES; i++, ptep++, addr += PAGE_SIZE) {
> +		pte_t ptent = __ptep_get_and_clear(mm, addr, ptep);
> +
> +		if (pte_dirty(ptent))
> +			pte = pte_mkdirty(pte);
> +
> +		if (pte_young(ptent))
> +			pte = pte_mkyoung(pte);
> +	}
> +
> +	__flush_tlb_range(&vma, start_addr, addr, PAGE_SIZE, true, 3);
> +
> +	__set_ptes(mm, start_addr, start_ptep, pte, CONT_PTES);
> +}
> +
> +void __contpte_try_fold(struct mm_struct *mm, unsigned long addr,
> +			pte_t *ptep, pte_t pte)
> +{
> +	/*
> +	 * We have already checked that the virtual and pysical addresses are
> +	 * correctly aligned for a contpte mapping in contpte_try_fold() so the
> +	 * remaining checks are to ensure that the contpte range is fully
> +	 * covered by a single folio, and ensure that all the ptes are valid
> +	 * with contiguous PFNs and matching prots. We ignore the state of the
> +	 * access and dirty bits for the purpose of deciding if its a contiguous
> +	 * range; the folding process will generate a single contpte entry which
> +	 * has a single access and dirty bit. Those 2 bits are the logical OR of
> +	 * their respective bits in the constituent pte entries. In order to
> +	 * ensure the contpte range is covered by a single folio, we must
> +	 * recover the folio from the pfn, but special mappings don't have a
> +	 * folio backing them. Fortunately contpte_try_fold() already checked
> +	 * that the pte is not special - we never try to fold special mappings.
> +	 * Note we can't use vm_normal_page() for this since we don't have the
> +	 * vma.
> +	 */
> +
> +	struct page *page = pte_page(pte);
> +	struct folio *folio = page_folio(page);
> +	unsigned long folio_saddr = addr - (page - &folio->page) * PAGE_SIZE;
> +	unsigned long folio_eaddr = folio_saddr + folio_nr_pages(folio) * PAGE_SIZE;
> +	unsigned long cont_saddr = ALIGN_DOWN(addr, CONT_PTE_SIZE);
> +	unsigned long cont_eaddr = cont_saddr + CONT_PTE_SIZE;
> +	unsigned long pfn;
> +	pgprot_t prot;
> +	pte_t subpte;
> +	pte_t *orig_ptep;
> +	int i;
> +
> +	if (folio_saddr > cont_saddr || folio_eaddr < cont_eaddr)
> +		return;
> +
> +	pfn = pte_pfn(pte) - ((addr - cont_saddr) >> PAGE_SHIFT);
> +	prot = pte_pgprot(pte_mkold(pte_mkclean(pte)));
> +	orig_ptep = ptep;
> +	ptep = contpte_align_down(ptep);
> +
> +	for (i = 0; i < CONT_PTES; i++, ptep++, pfn++) {
> +		subpte = __ptep_get(ptep);
> +		subpte = pte_mkold(pte_mkclean(subpte));
> +
> +		if (!pte_valid(subpte) ||
> +		    pte_pfn(subpte) != pfn ||
> +		    pgprot_val(pte_pgprot(subpte)) != pgprot_val(prot))
> +			return;
> +	}
> +
> +	contpte_fold(mm, addr, orig_ptep, pte, true);
> +}
> +EXPORT_SYMBOL(__contpte_try_fold);
> +
> +void __contpte_try_unfold(struct mm_struct *mm, unsigned long addr,
> +			pte_t *ptep, pte_t pte)
> +{
> +	/*
> +	 * We have already checked that the ptes are contiguous in
> +	 * contpte_try_unfold(), so we can unfold unconditionally here.
> +	 */
> +
> +	contpte_fold(mm, addr, ptep, pte, false);

I'm still working my way through the series but calling a fold during an
unfold stood out as it seemed wrong. Obviously further reading revealed
the boolean flag that changes the functions meaning but I think it would
be better to refactor that.

We could easily rename contpte_fold() to eg. set_cont_ptes() and factor
the pte calculation loop into a separate helper
(eg. calculate_contpte_dirty_young() or some hopefully better name)
called further up the stack. That has an added benefit of providing a
spot to add the nice comment for young/dirty rules you provided in the
patch description ;-)

In other words we'd have something like:

void __contpte_try_unfold() {
     pte = calculate_contpte_dirty_young(mm, addr, ptep, pte);
     pte = pte_mknoncont(pte);
     set_cont_ptes(mm, addr, ptep, pte);
}

Which IMHO is more immediately understandable.

 - Alistair

> +}
> +EXPORT_SYMBOL(__contpte_try_unfold);
> +
> +pte_t contpte_ptep_get(pte_t *ptep, pte_t orig_pte)
> +{
> +	/*
> +	 * Gather access/dirty bits, which may be populated in any of the ptes
> +	 * of the contig range. We are guarranteed to be holding the PTL, so any
> +	 * contiguous range cannot be unfolded or otherwise modified under our
> +	 * feet.
> +	 */
> +
> +	pte_t pte;
> +	int i;
> +
> +	ptep = contpte_align_down(ptep);
> +
> +	for (i = 0; i < CONT_PTES; i++, ptep++) {
> +		pte = __ptep_get(ptep);
> +
> +		if (pte_dirty(pte))
> +			orig_pte = pte_mkdirty(orig_pte);
> +
> +		if (pte_young(pte))
> +			orig_pte = pte_mkyoung(orig_pte);
> +	}
> +
> +	return orig_pte;
> +}
> +EXPORT_SYMBOL(contpte_ptep_get);
> +
> +pte_t contpte_ptep_get_lockless(pte_t *orig_ptep)
> +{
> +	/*
> +	 * Gather access/dirty bits, which may be populated in any of the ptes
> +	 * of the contig range. We may not be holding the PTL, so any contiguous
> +	 * range may be unfolded/modified/refolded under our feet. Therefore we
> +	 * ensure we read a _consistent_ contpte range by checking that all ptes
> +	 * in the range are valid and have CONT_PTE set, that all pfns are
> +	 * contiguous and that all pgprots are the same (ignoring access/dirty).
> +	 * If we find a pte that is not consistent, then we must be racing with
> +	 * an update so start again. If the target pte does not have CONT_PTE
> +	 * set then that is considered consistent on its own because it is not
> +	 * part of a contpte range.
> +	 */
> +
> +	pte_t orig_pte;
> +	pgprot_t orig_prot;
> +	pte_t *ptep;
> +	unsigned long pfn;
> +	pte_t pte;
> +	pgprot_t prot;
> +	int i;
> +
> +retry:
> +	orig_pte = __ptep_get(orig_ptep);
> +
> +	if (!pte_valid_cont(orig_pte))
> +		return orig_pte;
> +
> +	orig_prot = pte_pgprot(pte_mkold(pte_mkclean(orig_pte)));
> +	ptep = contpte_align_down(orig_ptep);
> +	pfn = pte_pfn(orig_pte) - (orig_ptep - ptep);
> +
> +	for (i = 0; i < CONT_PTES; i++, ptep++, pfn++) {
> +		pte = __ptep_get(ptep);
> +		prot = pte_pgprot(pte_mkold(pte_mkclean(pte)));
> +
> +		if (!pte_valid_cont(pte) ||
> +		   pte_pfn(pte) != pfn ||
> +		   pgprot_val(prot) != pgprot_val(orig_prot))
> +			goto retry;
> +
> +		if (pte_dirty(pte))
> +			orig_pte = pte_mkdirty(orig_pte);
> +
> +		if (pte_young(pte))
> +			orig_pte = pte_mkyoung(orig_pte);
> +	}
> +
> +	return orig_pte;
> +}
> +EXPORT_SYMBOL(contpte_ptep_get_lockless);
> +
> +void contpte_set_ptes(struct mm_struct *mm, unsigned long addr,
> +					pte_t *ptep, pte_t pte, unsigned int nr)
> +{
> +	unsigned long next;
> +	unsigned long end = addr + (nr << PAGE_SHIFT);
> +	unsigned long pfn = pte_pfn(pte);
> +	pgprot_t prot = pte_pgprot(pte);
> +	pte_t orig_pte;
> +
> +	do {
> +		next = pte_cont_addr_end(addr, end);
> +		nr = (next - addr) >> PAGE_SHIFT;
> +		pte = pfn_pte(pfn, prot);
> +
> +		if (((addr | next | (pfn << PAGE_SHIFT)) & ~CONT_PTE_MASK) == 0)
> +			pte = pte_mkcont(pte);
> +		else
> +			pte = pte_mknoncont(pte);
> +
> +		/*
> +		 * If operating on a partial contiguous range then we must first
> +		 * unfold the contiguous range if it was previously folded.
> +		 * Otherwise we could end up with overlapping tlb entries.
> +		 */
> +		if (nr != CONT_PTES)
> +			contpte_try_unfold(mm, addr, ptep, __ptep_get(ptep));
> +
> +		/*
> +		 * If we are replacing ptes that were contiguous or if the new
> +		 * ptes are contiguous and any of the ptes being replaced are
> +		 * valid, we need to clear and flush the range to prevent
> +		 * overlapping tlb entries.
> +		 */
> +		orig_pte = __ptep_get(ptep);
> +		if (pte_valid_cont(orig_pte) ||
> +		    (pte_cont(pte) && ptep_any_valid(ptep, nr)))
> +			ptep_clear_flush_range(mm, addr, ptep, nr);
> +
> +		__set_ptes(mm, addr, ptep, pte, nr);
> +
> +		addr = next;
> +		ptep += nr;
> +		pfn += nr;
> +
> +	} while (addr != end);
> +}
> +EXPORT_SYMBOL(contpte_set_ptes);
> +
> +int contpte_ptep_test_and_clear_young(struct vm_area_struct *vma,
> +					unsigned long addr, pte_t *ptep)
> +{
> +	/*
> +	 * ptep_clear_flush_young() technically requires us to clear the access
> +	 * flag for a _single_ pte. However, the core-mm code actually tracks
> +	 * access/dirty per folio, not per page. And since we only create a
> +	 * contig range when the range is covered by a single folio, we can get
> +	 * away with clearing young for the whole contig range here, so we avoid
> +	 * having to unfold.
> +	 */
> +
> +	int i;
> +	int young = 0;
> +
> +	ptep = contpte_align_down(ptep);
> +	addr = ALIGN_DOWN(addr, CONT_PTE_SIZE);
> +
> +	for (i = 0; i < CONT_PTES; i++, ptep++, addr += PAGE_SIZE)
> +		young |= __ptep_test_and_clear_young(vma, addr, ptep);
> +
> +	return young;
> +}
> +EXPORT_SYMBOL(contpte_ptep_test_and_clear_young);
> +
> +int contpte_ptep_clear_flush_young(struct vm_area_struct *vma,
> +					unsigned long addr, pte_t *ptep)
> +{
> +	int young;
> +
> +	young = contpte_ptep_test_and_clear_young(vma, addr, ptep);
> +
> +	if (young) {
> +		/*
> +		 * See comment in __ptep_clear_flush_young(); same rationale for
> +		 * eliding the trailing DSB applies here.
> +		 */
> +		addr = ALIGN_DOWN(addr, CONT_PTE_SIZE);
> +		__flush_tlb_range_nosync(vma, addr, addr + CONT_PTE_SIZE,
> +					 PAGE_SIZE, true, 3);
> +	}
> +
> +	return young;
> +}
> +EXPORT_SYMBOL(contpte_ptep_clear_flush_young);
> +
> +int contpte_ptep_set_access_flags(struct vm_area_struct *vma,
> +					unsigned long addr, pte_t *ptep,
> +					pte_t entry, int dirty)
> +{
> +	pte_t orig_pte;
> +	int i;
> +	unsigned long start_addr;
> +
> +	/*
> +	 * Gather the access/dirty bits for the contiguous range. If nothing has
> +	 * changed, its a noop.
> +	 */
> +	orig_pte = ptep_get(ptep);
> +	if (pte_val(orig_pte) == pte_val(entry))
> +		return 0;
> +
> +	/*
> +	 * We can fix up access/dirty bits without having to unfold/fold the
> +	 * contig range. But if the write bit is changing, we need to go through
> +	 * the full unfold/fold cycle.
> +	 */
> +	if (pte_write(orig_pte) == pte_write(entry)) {
> +		/*
> +		 * For HW access management, we technically only need to update
> +		 * the flag on a single pte in the range. But for SW access
> +		 * management, we need to update all the ptes to prevent extra
> +		 * faults. Avoid per-page tlb flush in __ptep_set_access_flags()
> +		 * and instead flush the whole range at the end.
> +		 */
> +		ptep = contpte_align_down(ptep);
> +		start_addr = addr = ALIGN_DOWN(addr, CONT_PTE_SIZE);
> +
> +		for (i = 0; i < CONT_PTES; i++, ptep++, addr += PAGE_SIZE)
> +			__ptep_set_access_flags(vma, addr, ptep, entry, 0);
> +
> +		if (dirty)
> +			__flush_tlb_range(vma, start_addr, addr,
> +							PAGE_SIZE, true, 3);
> +	} else {
> +		__contpte_try_unfold(vma->vm_mm, addr, ptep, orig_pte);
> +		__ptep_set_access_flags(vma, addr, ptep, entry, dirty);
> +		contpte_try_fold(vma->vm_mm, addr, ptep, entry);
> +	}
> +
> +	return 1;
> +}
> +EXPORT_SYMBOL(contpte_ptep_set_access_flags);