[PATCH 13/14] arm64: dts: renesas: rzg3s-smarc-som: Enable Ethernet interfaces
Claudiu
claudiu.beznea at tuxon.dev
Sun Nov 19 23:00:23 PST 2023
From: Claudiu Beznea <claudiu.beznea.uj at bp.renesas.com>
RZ/G3S Smarc Module has Ethernet PHYs (KSZ9131) connected to each Ethernet
IP. For this add proper DT bindings to enable the Ethernet communication
though these PHYs.
The interface b/w PHYs and MACs is RGMII. The skew settings were set to
zero as based on phy-mode (rgmii-id) the KSZ9131 driver enables internal
DLL which adds 2ns delay b/w clocks (TX/RX) and data signals.
Different pin settings were applied to TXC, TX_CTL compared with the rest
of the RGMII pins to comply with requirements for these pins imposed by
HW manual of RZ/G3S (see chapters "Ether Ch0 Voltage Mode Control
Register (ETH0_POC)", "Ether Ch1 Voltage Mode Control Register (ETH1_POC)",
for power source selection, "Ether MII/RGMII Mode Control Register
(ETH_MODE)" for output-enable and "Input Enable Control Register (IEN_m)"
for input-enable configurations).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj at bp.renesas.com>
---
Hi, Geert,
Please note that at the moment (on top of linux-next) the PHYs are probed
in poll mode as the interrupt controller support is not included yet.
It is work in progress (see [1]).
Thank you,
Claudiu Beznea
[1] https://lore.kernel.org/all/20231115142749.853106-1-claudiu.beznea.uj@bp.renesas.com/
.../boot/dts/renesas/rzg3s-smarc-som.dtsi | 145 +++++++++++++++++-
1 file changed, 144 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
index e090a4837468..571cade41647 100644
--- a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
@@ -25,7 +25,10 @@ / {
aliases {
mmc0 = &sdhi0;
-#if !SW_SD2_EN
+#if SW_SD2_EN
+ eth0 = ð0;
+ eth1 = ð1;
+#else
mmc2 = &sdhi2;
#endif
};
@@ -81,6 +84,64 @@ vcc_sdhi2: regulator2 {
};
};
+#if SW_SD2_EN
+ð0 {
+ pinctrl-0 = <ð0_pins>;
+ pinctrl-names = "default";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ phy0: ethernet-phy at 7 {
+ reg = <7>;
+ interrupt-parent = <&pinctrl>;
+ interrupts = <RZG2L_GPIO(12, 0) IRQ_TYPE_EDGE_FALLING>;
+ rxc-skew-psec = <0>;
+ txc-skew-psec = <0>;
+ rxdv-skew-psec = <0>;
+ txen-skew-psec = <0>;
+ rxd0-skew-psec = <0>;
+ rxd1-skew-psec = <0>;
+ rxd2-skew-psec = <0>;
+ rxd3-skew-psec = <0>;
+ txd0-skew-psec = <0>;
+ txd1-skew-psec = <0>;
+ txd2-skew-psec = <0>;
+ txd3-skew-psec = <0>;
+ };
+};
+
+ð1 {
+ pinctrl-0 = <ð1_pins>;
+ pinctrl-names = "default";
+ phy-handle = <&phy1>;
+ phy-mode = "rgmii-id";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ phy1: ethernet-phy at 7 {
+ reg = <7>;
+ interrupt-parent = <&pinctrl>;
+ interrupts = <RZG2L_GPIO(12, 1) IRQ_TYPE_EDGE_FALLING>;
+ rxc-skew-psec = <0>;
+ txc-skew-psec = <0>;
+ rxdv-skew-psec = <0>;
+ txen-skew-psec = <0>;
+ rxd0-skew-psec = <0>;
+ rxd1-skew-psec = <0>;
+ rxd2-skew-psec = <0>;
+ rxd3-skew-psec = <0>;
+ txd0-skew-psec = <0>;
+ txd1-skew-psec = <0>;
+ txd2-skew-psec = <0>;
+ txd3-skew-psec = <0>;
+ };
+};
+#endif
+
&extal_clk {
clock-frequency = <24000000>;
};
@@ -128,6 +189,88 @@ &sdhi2 {
#endif
&pinctrl {
+ eth0-phy-irq-hog {
+ gpio-hog;
+ gpios = <RZG2L_GPIO(12, 0) GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "eth0-phy-irq";
+ };
+
+ eth0_pins: eth0 {
+ txc {
+ pinmux = <RZG2L_PORT_PINMUX(1, 0, 1)>; /* ET0_TXC */
+ power-source = <1800>;
+ output-enable;
+ input-enable;
+ drive-strength-microamp = <5200>;
+ };
+
+ tx_ctl {
+ pinmux = <RZG2L_PORT_PINMUX(1, 1, 1)>; /* ET0_TX_CTL */
+ power-source = <1800>;
+ output-enable;
+ drive-strength-microamp = <5200>;
+ };
+
+ mux {
+ pinmux = <RZG2L_PORT_PINMUX(1, 2, 1)>, /* ET0_TXD0 */
+ <RZG2L_PORT_PINMUX(1, 3, 1)>, /* ET0_TXD1 */
+ <RZG2L_PORT_PINMUX(1, 4, 1)>, /* ET0_TXD2 */
+ <RZG2L_PORT_PINMUX(2, 0, 1)>, /* ET0_TXD3 */
+ <RZG2L_PORT_PINMUX(3, 0, 1)>, /* ET0_RXC */
+ <RZG2L_PORT_PINMUX(3, 1, 1)>, /* ET0_RX_CTL */
+ <RZG2L_PORT_PINMUX(3, 2, 1)>, /* ET0_RXD0 */
+ <RZG2L_PORT_PINMUX(3, 3, 1)>, /* ET0_RXD1 */
+ <RZG2L_PORT_PINMUX(4, 0, 1)>, /* ET0_RXD2 */
+ <RZG2L_PORT_PINMUX(4, 1, 1)>, /* ET0_RXD3 */
+ <RZG2L_PORT_PINMUX(4, 3, 1)>, /* ET0_MDC */
+ <RZG2L_PORT_PINMUX(4, 4, 1)>, /* ET0_MDIO */
+ <RZG2L_PORT_PINMUX(4, 5, 1)>; /* ET0_LINKSTA */
+ power-source = <1800>;
+ };
+ };
+
+ eth1-phy-irq-hog {
+ gpio-hog;
+ gpios = <RZG2L_GPIO(12, 1) GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "eth1-phy-irq";
+ };
+
+ eth1_pins: eth1 {
+ txc {
+ pinmux = <RZG2L_PORT_PINMUX(7, 0, 1)>; /* ET1_TXC */
+ power-source = <1800>;
+ output-enable;
+ input-enable;
+ drive-strength-microamp = <5200>;
+ };
+
+ tx_ctl {
+ pinmux = <RZG2L_PORT_PINMUX(7, 1, 1)>; /* ET1_TX_CTL */
+ power-source = <1800>;
+ output-enable;
+ drive-strength-microamp = <5200>;
+ };
+
+ mux {
+ pinmux = <RZG2L_PORT_PINMUX(7, 2, 1)>, /* ET1_TXD0 */
+ <RZG2L_PORT_PINMUX(7, 3, 1)>, /* ET1_TXD1 */
+ <RZG2L_PORT_PINMUX(7, 4, 1)>, /* ET1_TXD2 */
+ <RZG2L_PORT_PINMUX(8, 0, 1)>, /* ET1_TXD3 */
+ <RZG2L_PORT_PINMUX(8, 4, 1)>, /* ET1_RXC */
+ <RZG2L_PORT_PINMUX(9, 0, 1)>, /* ET1_RX_CTL */
+ <RZG2L_PORT_PINMUX(9, 1, 1)>, /* ET1_RXD0 */
+ <RZG2L_PORT_PINMUX(9, 2, 1)>, /* ET1_RXD1 */
+ <RZG2L_PORT_PINMUX(9, 3, 1)>, /* ET1_RXD2 */
+ <RZG2L_PORT_PINMUX(10, 0, 1)>, /* ET1_RXD3 */
+ <RZG2L_PORT_PINMUX(10, 2, 1)>, /* ET1_MDC */
+ <RZG2L_PORT_PINMUX(10, 3, 1)>, /* ET1_MDIO */
+ <RZG2L_PORT_PINMUX(10, 4, 1)>; /* ET1_LINKSTA */
+ power-source = <1800>;
+ };
+ };
+
sdhi0_pins: sd0 {
data {
pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
--
2.39.2
More information about the linux-arm-kernel
mailing list