[PATCH v3 1/5] phy: rockchip-inno-usb2: Split ID interrupt phy registers

Alex Bee knaerzche at gmail.com
Sun Nov 19 04:13:36 PST 2023


Commit 51a9b2c03dd3 ("phy: rockchip-inno-usb2: Handle ID IRQ") added ID
detection interrupt registers. However the current implementation assumes
that falling and rising edge interrupt are always enabled in registers
spanning over subsequent bits.
That is not the case for RK3128's version of the phy and this
implementation can't be used as-is, since there are bits with different
purpose in between.

This splits up the register definitions for id_det_en, id_det_en and
id_det_clr registers in rising and falling edge variants.
It's required as preparation to support RK3128's Innosilicon usb2 phy as
well in this driver and matches pretty much to what the vendor does, so I'm
not expecting issues for other SoCs with that change.

Signed-off-by: Alex Bee <knaerzche at gmail.com>
---
Changes in v3:
 - rebased on linux-next
 
 drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 99 +++++++++++++------
 1 file changed, 70 insertions(+), 29 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
index a24d2af154df..b5a1d30df83a 100644
--- a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
+++ b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
@@ -123,9 +123,12 @@ struct rockchip_chg_det_reg {
  * @disrise_en: host disconnect rise edge detection enable.
  * @disrise_st: host disconnect rise edge detection state.
  * @disrise_clr: host disconnect rise edge detection clear.
- * @id_det_en: id detection enable register.
- * @id_det_st: id detection state register.
- * @id_det_clr: id detection clear register.
+ * @idfall_det_en: id detection enable register, falling edge
+ * @idfall_det_st: id detection state register, falling edge
+ * @idfall_det_clr: id detection clear register, falling edge
+ * @idrise_det_en: id detection enable register, rising edge
+ * @idrise_det_st: id detection state register, rising edge
+ * @idrise_det_clr: id detection clear register, rising edge
  * @ls_det_en: linestate detection enable register.
  * @ls_det_st: linestate detection state register.
  * @ls_det_clr: linestate detection clear register.
@@ -146,9 +149,12 @@ struct rockchip_usb2phy_port_cfg {
 	struct usb2phy_reg      disrise_en;
 	struct usb2phy_reg      disrise_st;
 	struct usb2phy_reg      disrise_clr;
-	struct usb2phy_reg	id_det_en;
-	struct usb2phy_reg	id_det_st;
-	struct usb2phy_reg	id_det_clr;
+	struct usb2phy_reg	idfall_det_en;
+	struct usb2phy_reg	idfall_det_st;
+	struct usb2phy_reg	idfall_det_clr;
+	struct usb2phy_reg	idrise_det_en;
+	struct usb2phy_reg	idrise_det_st;
+	struct usb2phy_reg	idrise_det_clr;
 	struct usb2phy_reg	ls_det_en;
 	struct usb2phy_reg	ls_det_st;
 	struct usb2phy_reg	ls_det_clr;
@@ -488,15 +494,27 @@ static int rockchip_usb2phy_init(struct phy *phy)
 			if (ret)
 				goto out;
 
-			/* clear id status and enable id detect irq */
+			/* clear id status and enable id detect irqs */
 			ret = property_enable(rphy->grf,
-					      &rport->port_cfg->id_det_clr,
+					      &rport->port_cfg->idfall_det_clr,
 					      true);
 			if (ret)
 				goto out;
 
 			ret = property_enable(rphy->grf,
-					      &rport->port_cfg->id_det_en,
+					      &rport->port_cfg->idrise_det_clr,
+					      true);
+			if (ret)
+				goto out;
+
+			ret = property_enable(rphy->grf,
+					      &rport->port_cfg->idfall_det_en,
+					      true);
+			if (ret)
+				goto out;
+
+			ret = property_enable(rphy->grf,
+					      &rport->port_cfg->idrise_det_en,
 					      true);
 			if (ret)
 				goto out;
@@ -1030,11 +1048,16 @@ static irqreturn_t rockchip_usb2phy_id_irq(int irq, void *data)
 	struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
 	bool id;
 
-	if (!property_enabled(rphy->grf, &rport->port_cfg->id_det_st))
+	if (!property_enabled(rphy->grf, &rport->port_cfg->idfall_det_st) &&
+	    !property_enabled(rphy->grf, &rport->port_cfg->idrise_det_st))
 		return IRQ_NONE;
 
 	/* clear id detect irq pending status */
-	property_enable(rphy->grf, &rport->port_cfg->id_det_clr, true);
+	if (property_enabled(rphy->grf, &rport->port_cfg->idfall_det_st))
+		property_enable(rphy->grf, &rport->port_cfg->idfall_det_clr, true);
+
+	if (property_enabled(rphy->grf, &rport->port_cfg->idrise_det_st))
+		property_enable(rphy->grf, &rport->port_cfg->idrise_det_clr, true);
 
 	id = property_enabled(rphy->grf, &rport->port_cfg->utmi_id);
 	extcon_set_state_sync(rphy->edev, EXTCON_USB_HOST, !id);
@@ -1524,9 +1547,12 @@ static const struct rockchip_usb2phy_cfg rk3228_phy_cfgs[] = {
 				.bvalid_det_en	= { 0x0680, 3, 3, 0, 1 },
 				.bvalid_det_st	= { 0x0690, 3, 3, 0, 1 },
 				.bvalid_det_clr	= { 0x06a0, 3, 3, 0, 1 },
-				.id_det_en	= { 0x0680, 6, 5, 0, 3 },
-				.id_det_st	= { 0x0690, 6, 5, 0, 3 },
-				.id_det_clr	= { 0x06a0, 6, 5, 0, 3 },
+				.idfall_det_en	= { 0x0680, 6, 6, 0, 1 },
+				.idfall_det_st	= { 0x0690, 6, 6, 0, 1 },
+				.idfall_det_clr	= { 0x06a0, 6, 6, 0, 1 },
+				.idrise_det_en	= { 0x0680, 5, 5, 0, 1 },
+				.idrise_det_st	= { 0x0690, 5, 5, 0, 1 },
+				.idrise_det_clr	= { 0x06a0, 5, 5, 0, 1 },
 				.ls_det_en	= { 0x0680, 2, 2, 0, 1 },
 				.ls_det_st	= { 0x0690, 2, 2, 0, 1 },
 				.ls_det_clr	= { 0x06a0, 2, 2, 0, 1 },
@@ -1587,9 +1613,12 @@ static const struct rockchip_usb2phy_cfg rk3308_phy_cfgs[] = {
 				.bvalid_det_en	= { 0x3020, 3, 2, 0, 3 },
 				.bvalid_det_st	= { 0x3024, 3, 2, 0, 3 },
 				.bvalid_det_clr = { 0x3028, 3, 2, 0, 3 },
-				.id_det_en	= { 0x3020, 5, 4, 0, 3 },
-				.id_det_st	= { 0x3024, 5, 4, 0, 3 },
-				.id_det_clr	= { 0x3028, 5, 4, 0, 3 },
+				.idfall_det_en	= { 0x3020, 5, 5, 0, 1 },
+				.idfall_det_st	= { 0x3024, 5, 5, 0, 1 },
+				.idfall_det_clr = { 0x3028, 5, 5, 0, 1 },
+				.idrise_det_en	= { 0x3020, 4, 4, 0, 1 },
+				.idrise_det_st	= { 0x3024, 4, 4, 0, 1 },
+				.idrise_det_clr = { 0x3028, 4, 4, 0, 1 },
 				.ls_det_en	= { 0x3020, 0, 0, 0, 1 },
 				.ls_det_st	= { 0x3024, 0, 0, 0, 1 },
 				.ls_det_clr	= { 0x3028, 0, 0, 0, 1 },
@@ -1634,9 +1663,12 @@ static const struct rockchip_usb2phy_cfg rk3328_phy_cfgs[] = {
 				.bvalid_det_en	= { 0x0110, 3, 2, 0, 3 },
 				.bvalid_det_st	= { 0x0114, 3, 2, 0, 3 },
 				.bvalid_det_clr = { 0x0118, 3, 2, 0, 3 },
-				.id_det_en	= { 0x0110, 5, 4, 0, 3 },
-				.id_det_st	= { 0x0114, 5, 4, 0, 3 },
-				.id_det_clr	= { 0x0118, 5, 4, 0, 3 },
+				.idfall_det_en	= { 0x0110, 5, 5, 0, 1 },
+				.idfall_det_st	= { 0x0114, 5, 5, 0, 1 },
+				.idfall_det_clr = { 0x0118, 5, 5, 0, 1 },
+				.idrise_det_en	= { 0x0110, 4, 4, 0, 1 },
+				.idrise_det_st	= { 0x0114, 4, 4, 0, 1 },
+				.idrise_det_clr = { 0x0118, 4, 4, 0, 1 },
 				.ls_det_en	= { 0x0110, 0, 0, 0, 1 },
 				.ls_det_st	= { 0x0114, 0, 0, 0, 1 },
 				.ls_det_clr	= { 0x0118, 0, 0, 0, 1 },
@@ -1700,9 +1732,12 @@ static const struct rockchip_usb2phy_cfg rk3399_phy_cfgs[] = {
 				.bvalid_det_en	= { 0xe3c0, 3, 3, 0, 1 },
 				.bvalid_det_st	= { 0xe3e0, 3, 3, 0, 1 },
 				.bvalid_det_clr	= { 0xe3d0, 3, 3, 0, 1 },
-				.id_det_en	= { 0xe3c0, 5, 4, 0, 3 },
-				.id_det_st	= { 0xe3e0, 5, 4, 0, 3 },
-				.id_det_clr	= { 0xe3d0, 5, 4, 0, 3 },
+				.idfall_det_en	= { 0xe3c0, 5, 5, 0, 1 },
+				.idfall_det_st	= { 0xe3e0, 5, 5, 0, 1 },
+				.idfall_det_clr	= { 0xe3d0, 5, 5, 0, 1 },
+				.idrise_det_en	= { 0xe3c0, 4, 4, 0, 1 },
+				.idrise_det_st	= { 0xe3e0, 4, 4, 0, 1 },
+				.idrise_det_clr	= { 0xe3d0, 4, 4, 0, 1 },
 				.utmi_avalid	= { 0xe2ac, 7, 7, 0, 1 },
 				.utmi_bvalid	= { 0xe2ac, 12, 12, 0, 1 },
 				.utmi_id	= { 0xe2ac, 8, 8, 0, 1 },
@@ -1739,9 +1774,12 @@ static const struct rockchip_usb2phy_cfg rk3399_phy_cfgs[] = {
 				.bvalid_det_en  = { 0xe3c0, 8, 8, 0, 1 },
 				.bvalid_det_st  = { 0xe3e0, 8, 8, 0, 1 },
 				.bvalid_det_clr = { 0xe3d0, 8, 8, 0, 1 },
-				.id_det_en	= { 0xe3c0, 10, 9, 0, 3 },
-				.id_det_st	= { 0xe3e0, 10, 9, 0, 3 },
-				.id_det_clr	= { 0xe3d0, 10, 9, 0, 3 },
+				.idfall_det_en	= { 0xe3c0, 10, 10, 0, 1 },
+				.idfall_det_st	= { 0xe3e0, 10, 10, 0, 1 },
+				.idfall_det_clr	= { 0xe3d0, 10, 10, 0, 1 },
+				.idrise_det_en	= { 0xe3c0, 9, 9, 0, 1 },
+				.idrise_det_st	= { 0xe3e0, 9, 9, 0, 1 },
+				.idrise_det_clr	= { 0xe3d0, 9, 9, 0, 1 },
 				.utmi_avalid	= { 0xe2ac, 10, 10, 0, 1 },
 				.utmi_bvalid    = { 0xe2ac, 16, 16, 0, 1 },
 				.utmi_id	= { 0xe2ac, 11, 11, 0, 1 },
@@ -1770,9 +1808,12 @@ static const struct rockchip_usb2phy_cfg rk3568_phy_cfgs[] = {
 				.bvalid_det_en	= { 0x0080, 3, 2, 0, 3 },
 				.bvalid_det_st	= { 0x0084, 3, 2, 0, 3 },
 				.bvalid_det_clr = { 0x0088, 3, 2, 0, 3 },
-				.id_det_en	= { 0x0080, 5, 4, 0, 3 },
-				.id_det_st	= { 0x0084, 5, 4, 0, 3 },
-				.id_det_clr	= { 0x0088, 5, 4, 0, 3 },
+				.idfall_det_en	= { 0x0080, 5, 5, 0, 1 },
+				.idfall_det_st	= { 0x0084, 5, 5, 0, 1 },
+				.idfall_det_clr	= { 0x0088, 5, 5, 0, 1 },
+				.idrise_det_en	= { 0x0080, 4, 4, 0, 1 },
+				.idrise_det_st	= { 0x0084, 4, 4, 0, 1 },
+				.idrise_det_clr	= { 0x0088, 4, 4, 0, 1 },
 				.utmi_avalid	= { 0x00c0, 10, 10, 0, 1 },
 				.utmi_bvalid	= { 0x00c0, 9, 9, 0, 1 },
 				.utmi_id	= { 0x00c0, 6, 6, 0, 1 },
-- 
2.42.0




More information about the linux-arm-kernel mailing list