[RFC PATCH] ARM: dts: stm32f469-disco: use the same 3v3 for SD and DSI nodes

[Alexandre TORGUE]

Hi Dario



On 10/23/23 13:00, Dario Binacchi wrote:
> Hello Alexandre,
> 
> On Thu, Sep 14, 2023 at 10:57 AM Alexandre TORGUE
> <alexandre.torgue at foss.st.com> wrote:
>>
>> On 9/4/23 20:06, Dario Binacchi wrote:
>>> In the board schematic, the power supply for the SD card is the same 3.3
>>> volts used to power the LCD panel and other peripherals. By generalizing
>>> the name of the voltage regulator, it simplifies the device tree and makes
>>> it more readable.
>>>
>>
>> It makes sens as it is the same discret regulator (no pmic involved).
>>
> 
> I don't see it applied to linux-stm32/next. Is something missing?

ok, It is because the [RFC..] has been kept. Please resend by dropping it.

Cheers
Alex

> 
> Thanks and regards,
> Dario
> 
>> regards
>> Alex
>>
>>> Link: https://www.st.com/en/evaluation-tools/32f469idiscovery.html#cad-resources
>>> Signed-off-by: Dario Binacchi <dario.binacchi at amarulasolutions.com>
>>>
>>> ---
>>>
>>>    arch/arm/boot/dts/st/stm32f469-disco.dts | 15 ++++-----------
>>>    1 file changed, 4 insertions(+), 11 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/st/stm32f469-disco.dts b/arch/arm/boot/dts/st/stm32f469-disco.dts
>>> index cbbd521bf010..8a4f8ddd083d 100644
>>> --- a/arch/arm/boot/dts/st/stm32f469-disco.dts
>>> +++ b/arch/arm/boot/dts/st/stm32f469-disco.dts
>>> @@ -69,16 +69,9 @@ aliases {
>>>                serial0 = &usart3;
>>>        };
>>>
>>> -     mmc_vcard: mmc_vcard {
>>> +     vcc_3v3: vcc-3v3 {
>>>                compatible = "regulator-fixed";
>>> -             regulator-name = "mmc_vcard";
>>> -             regulator-min-microvolt = <3300000>;
>>> -             regulator-max-microvolt = <3300000>;
>>> -     };
>>> -
>>> -     vdd_dsi: vdd-dsi {
>>> -             compatible = "regulator-fixed";
>>> -             regulator-name = "vdd_dsi";
>>> +             regulator-name = "vcc_3v3";
>>>                regulator-min-microvolt = <3300000>;
>>>                regulator-max-microvolt = <3300000>;
>>>        };
>>> @@ -164,7 +157,7 @@ panel at 0 {
>>>                compatible = "orisetech,otm8009a";
>>>                reg = <0>; /* dsi virtual channel (0..3) */
>>>                reset-gpios = <&gpioh 7 GPIO_ACTIVE_LOW>;
>>> -             power-supply = <&vdd_dsi>;
>>> +             power-supply = <&vcc_3v3>;
>>>                status = "okay";
>>>
>>>                port {
>>> @@ -219,7 +212,7 @@ timer at 2 {
>>>
>>>    &sdio {
>>>        status = "okay";
>>> -     vmmc-supply = <&mmc_vcard>;
>>> +     vmmc-supply = <&vcc_3v3>;
>>>        cd-gpios = <&gpiog 2 GPIO_ACTIVE_LOW>;
>>>        broken-cd;
>>>        pinctrl-names = "default", "opendrain";
>>
> 
>