[PATCH v5 05/17] clk: meson: g12a: make VCLK2 and ENCL clock path configurable by CCF
Neil Armstrong
neil.armstrong at linaro.org
Tue May 30 08:57:51 PDT 2023
On 30/05/2023 10:14, Jerome Brunet wrote:
>
> On Tue 30 May 2023 at 09:38, Neil Armstrong <neil.armstrong at linaro.org> wrote:
>
>> In order to setup the DSI clock, let's make the unused VCLK2 clock path
>> configuration via CCF.
>>
>> The nocache option is removed from following clocks:
>> - vclk2_sel
>> - vclk2_input
>> - vclk2_div
>> - vclk2
>> - vclk_div1
>> - vclk2_div2_en
>> - vclk2_div4_en
>> - vclk2_div6_en
>> - vclk2_div12_en
>> - vclk2_div2
>> - vclk2_div4
>> - vclk2_div6
>> - vclk2_div12
>> - cts_encl_sel
>>
>> The missing vclk2 reset sequence is handled via new clkc notifiers
>> in order to reset the vclk2 after each rate change as done by Amlogic
>> in the vendor implementation.
>>
>> In order to set a rate on cts_encl via the vclk2 clock path,
>> the NO_REPARENT flag is set on cts_encl_sel & vclk2_sel in order
>> to keep CCF from selection a parent.
>> The parents of cts_encl_sel & vclk2_sel are expected to be defined
>> in DT.
>>
>> The following clock scheme is to be used for DSI:
>>
>> xtal
>> \_ gp0_pll_dco
>> \_ gp0_pll
>> |- vclk2_sel
>> | \_ vclk2_input
>> | \_ vclk2_div
>> | \_ vclk2
>> | \_ vclk2_div1
>> | \_ cts_encl_sel
>> | \_ cts_encl -> to VPU LCD Encoder
>> |- mipi_dsi_pxclk_sel
>> \_ mipi_dsi_pxclk_div
>> \_ mipi_dsi_pxclk -> to DSI controller
>>
>> The mipi_dsi_pxclk_div is set as RO in order to use the same GP0
>> for mipi_dsi_pxclk and vclk2_input.
>
> I don't think notifiers is the appropriate approach here.
> Whenever there is clock change the motifiers would trigger an off/on of
> the clock, regardless of the clock usage or state.
> If you have several consummers on this vclk2, this would
> cause glitches and maybe this is not desirable.
>
> I think it would be better to handle the enable and reset with a
> specific gate driver, in prepare() or enable(), and the give the clock
> CLK_SET_RATE_GATE flag.
>
> This would require the clock to be properly turn off before changing the
> rate.
Sure, will see how to switch to that, seem Martin did than on Meson8.
Neil
>
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong at linaro.org>
>> ---
>> drivers/clk/meson/g12a.c | 131 +++++++++++++++++++++++++++++++++++++++++++----
>> 1 file changed, 120 insertions(+), 11 deletions(-)
>>
>> diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
>> index 461ebd79497c..e4053f4957d5 100644
>> --- a/drivers/clk/meson/g12a.c
>> +++ b/drivers/clk/meson/g12a.c
>> @@ -3163,7 +3163,7 @@ static struct clk_regmap g12a_vclk2_sel = {
>> .ops = &clk_regmap_mux_ops,
>> .parent_hws = g12a_vclk_parent_hws,
>> .num_parents = ARRAY_SIZE(g12a_vclk_parent_hws),
>> - .flags = CLK_SET_RATE_NO_REPARENT | CLK_GET_RATE_NOCACHE,
>> + .flags = CLK_SET_RATE_NO_REPARENT,
>> },
>> };
>>
>> @@ -3191,7 +3191,6 @@ static struct clk_regmap g12a_vclk2_input = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2_sel.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> },
>> };
>>
>> @@ -3212,6 +3211,40 @@ static struct clk_regmap g12a_vclk_div = {
>> },
>> };
>>
>> +struct g12a_vclk_div_notifier {
>> + struct clk_regmap *clk;
>> + unsigned int offset;
>> + u8 en_bit_idx;
>> + u8 reset_bit_idx;
>> + struct notifier_block nb;
>> +};
>> +
>> +static int g12a_vclk_div_notifier_cb(struct notifier_block *nb,
>> + unsigned long event, void *data)
>> +{
>> + struct g12a_vclk_div_notifier *nb_data =
>> + container_of(nb, struct g12a_vclk_div_notifier, nb);
>> +
>> + switch (event) {
>> + case PRE_RATE_CHANGE:
>> + /* disable and reset vclk2 divider */
>> + regmap_update_bits(nb_data->clk->map, nb_data->offset,
>> + BIT(nb_data->en_bit_idx) |
>> + BIT(nb_data->reset_bit_idx),
>> + BIT(nb_data->reset_bit_idx));
>> + return NOTIFY_OK;
>> + case POST_RATE_CHANGE:
>> + /* enabled and release reset */
>> + regmap_update_bits(nb_data->clk->map, nb_data->offset,
>> + BIT(nb_data->en_bit_idx) |
>> + BIT(nb_data->reset_bit_idx),
>> + BIT(nb_data->en_bit_idx));
>> + return NOTIFY_OK;
>> + default:
>> + return NOTIFY_DONE;
>> + };
>> +};
>> +
>> static struct clk_regmap g12a_vclk2_div = {
>> .data = &(struct clk_regmap_div_data){
>> .offset = HHI_VIID_CLK_DIV,
>> @@ -3225,10 +3258,18 @@ static struct clk_regmap g12a_vclk2_div = {
>> &g12a_vclk2_input.hw
>> },
>> .num_parents = 1,
>> - .flags = CLK_GET_RATE_NOCACHE,
>> + .flags = CLK_DIVIDER_ROUND_CLOSEST,
>> },
>> };
>>
>> +static struct g12a_vclk_div_notifier g12a_vclk2_div_data = {
>> + .clk = &g12a_vclk2_div,
>> + .offset = HHI_VIID_CLK_DIV,
>> + .en_bit_idx = 16,
>> + .reset_bit_idx = 17,
>> + .nb.notifier_call = g12a_vclk_div_notifier_cb,
>> +};
>> +
>> static struct clk_regmap g12a_vclk = {
>> .data = &(struct clk_regmap_gate_data){
>> .offset = HHI_VID_CLK_CNTL,
>> @@ -3243,6 +3284,33 @@ static struct clk_regmap g12a_vclk = {
>> },
>> };
>>
>> +struct g12a_vclk_reset_notifier {
>> + struct clk_regmap *clk;
>> + unsigned int offset;
>> + u8 bit_idx;
>> + struct notifier_block nb;
>> +};
>> +
>> +static int g12a_vclk_notifier_cb(struct notifier_block *nb,
>> + unsigned long event, void *data)
>> +{
>> + struct g12a_vclk_reset_notifier *nb_data =
>> + container_of(nb, struct g12a_vclk_reset_notifier, nb);
>> +
>> + switch (event) {
>> + case POST_RATE_CHANGE:
>> + /* reset vclk2 */
>> + regmap_update_bits(nb_data->clk->map, nb_data->offset,
>> + BIT(nb_data->bit_idx), BIT(nb_data->bit_idx));
>> + regmap_update_bits(nb_data->clk->map, nb_data->offset,
>> + BIT(nb_data->bit_idx), 0);
>> +
>> + return NOTIFY_OK;
>> + default:
>> + return NOTIFY_DONE;
>> + };
>> +}
>> +
>> static struct clk_regmap g12a_vclk2 = {
>> .data = &(struct clk_regmap_gate_data){
>> .offset = HHI_VIID_CLK_CNTL,
>> @@ -3253,10 +3321,17 @@ static struct clk_regmap g12a_vclk2 = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2_div.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> +static struct g12a_vclk_reset_notifier g12a_vclk2_data = {
>> + .clk = &g12a_vclk2,
>> + .offset = HHI_VIID_CLK_CNTL,
>> + .bit_idx = 15,
>> + .nb.notifier_call = g12a_vclk_notifier_cb,
>> +};
>> +
>> static struct clk_regmap g12a_vclk_div1 = {
>> .data = &(struct clk_regmap_gate_data){
>> .offset = HHI_VID_CLK_CNTL,
>> @@ -3337,7 +3412,7 @@ static struct clk_regmap g12a_vclk2_div1 = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3351,7 +3426,7 @@ static struct clk_regmap g12a_vclk2_div2_en = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3365,7 +3440,7 @@ static struct clk_regmap g12a_vclk2_div4_en = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3379,7 +3454,7 @@ static struct clk_regmap g12a_vclk2_div6_en = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3393,7 +3468,7 @@ static struct clk_regmap g12a_vclk2_div12_en = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3459,6 +3534,7 @@ static struct clk_fixed_factor g12a_vclk2_div2 = {
>> &g12a_vclk2_div2_en.hw
>> },
>> .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3472,6 +3548,7 @@ static struct clk_fixed_factor g12a_vclk2_div4 = {
>> &g12a_vclk2_div4_en.hw
>> },
>> .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3485,6 +3562,7 @@ static struct clk_fixed_factor g12a_vclk2_div6 = {
>> &g12a_vclk2_div6_en.hw
>> },
>> .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3498,6 +3576,7 @@ static struct clk_fixed_factor g12a_vclk2_div12 = {
>> &g12a_vclk2_div12_en.hw
>> },
>> .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3559,7 +3638,7 @@ static struct clk_regmap g12a_cts_encl_sel = {
>> .ops = &clk_regmap_mux_ops,
>> .parent_hws = g12a_cts_parent_hws,
>> .num_parents = ARRAY_SIZE(g12a_cts_parent_hws),
>> - .flags = CLK_SET_RATE_NO_REPARENT | CLK_GET_RATE_NOCACHE,
>> + .flags = CLK_SET_RATE_NO_REPARENT | CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3727,7 +3806,7 @@ static struct clk_regmap g12a_mipi_dsi_pxclk_div = {
>> },
>> .hw.init = &(struct clk_init_data){
>> .name = "mipi_dsi_pxclk_div",
>> - .ops = &clk_regmap_divider_ops,
>> + .ops = &clk_regmap_divider_ro_ops,
>> .parent_hws = (const struct clk_hw *[]) {
>> &g12a_mipi_dsi_pxclk_sel.hw
>> },
>> @@ -5421,6 +5500,32 @@ static int meson_g12a_dvfs_setup(struct platform_device *pdev)
>> return 0;
>> }
>>
>> +static int meson_g12a_vclk_setup(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct clk *notifier_clk;
>> + int ret;
>> +
>> + /* Setup clock notifier for vclk2 */
>> + notifier_clk = devm_clk_hw_get_clk(dev, &g12a_vclk2.hw, DVFS_CON_ID);
>> + ret = devm_clk_notifier_register(dev, notifier_clk, &g12a_vclk2_data.nb);
>> + if (ret) {
>> + dev_err(dev, "failed to register the vlkc2 notifier\n");
>> + return ret;
>> + }
>> +
>> + /* Setup clock notifier for vclk2_div */
>> + notifier_clk = devm_clk_hw_get_clk(dev, &g12a_vclk2_div.hw, DVFS_CON_ID);
>> + ret = devm_clk_notifier_register(dev, notifier_clk,
>> + &g12a_vclk2_div_data.nb);
>> + if (ret) {
>> + dev_err(dev, "failed to register the vclk2_div notifier\n");
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> struct meson_g12a_data {
>> const struct meson_eeclkc_data eeclkc_data;
>> int (*dvfs_setup)(struct platform_device *pdev);
>> @@ -5443,6 +5548,10 @@ static int meson_g12a_probe(struct platform_device *pdev)
>> g12a_data = container_of(eeclkc_data, struct meson_g12a_data,
>> eeclkc_data);
>>
>> + ret = meson_g12a_vclk_setup(pdev);
>> + if (ret)
>> + return ret;
>> +
>> if (g12a_data->dvfs_setup)
>> return g12a_data->dvfs_setup(pdev);
>
More information about the linux-arm-kernel
mailing list