[PATCH v2 4/4] cpufreq: mediatek: Raise proc and sram max voltage for MT7622/7623
Daniel Golle
daniel at makrotopia.org
Fri May 26 03:27:15 PDT 2023
On Fri, May 26, 2023 at 08:27:25AM +0000, Jia-wei Chang (張佳偉) wrote:
> On Wed, 2023-05-24 at 13:42 +0100, Daniel Golle wrote:
> > On Wed, May 24, 2023 at 08:43:31AM +0000, Jia-wei Chang (張佳偉) wrote:
> > > On Wed, 2023-05-24 at 09:28 +0200, AngeloGioacchino Del Regno wrote:
> > > > Il 23/05/23 19:37, Daniel Golle ha scritto:
> > > > > On Tue, May 23, 2023 at 04:56:47PM +0200, AngeloGioacchino Del
> > > > > Regno wrote:
> > > > > > Il 22/05/23 20:03, Daniel Golle ha scritto:
> > > > > > > Hi Jia-Wei,
> > > > > > > Hi AngeloGioacchino,
> > > > > > >
> > > > > > > On Fri, Mar 24, 2023 at 06:11:30PM +0800, jia-wei.chang
> > > > > > > wrote:
> > > > > > > > From: AngeloGioacchino Del Regno <
> > > > > > > > angelogioacchino.delregno at collabora.com>
> > > > > > > >
> > > > > > > > During the addition of SRAM voltage tracking for CCI
> > > > > > > > scaling,
> > > > > > > > this
> > > > > > > > driver got some voltage limits set for the vtrack
> > > > > > > > algorithm:
> > > > > > > > these
> > > > > > > > were moved to platform data first, then enforced in a
> > > > > > > > later
> > > > > > > > commit
> > > > > > > > 6a17b3876bc8 ("cpufreq: mediatek: Refine
> > > > > > > > mtk_cpufreq_voltage_tracking()")
> > > > > > > > using these as max values for the regulator_set_voltage()
> > > > > > > > calls.
> > > > > > > >
> > > > > > > > In this case, the vsram/vproc constraints for MT7622 and
> > > > > > > > MT7623
> > > > > > > > were supposed to be the same as MT2701 (and a number of
> > > > > > > > other
> > > > > > > > SoCs),
> > > > > > > > but that turned out to be a mistake because the
> > > > > > > > aforementioned two
> > > > > > > > SoCs' maximum voltage for both VPROC and VPROC_SRAM is
> > > > > > > > 1.36V.
> > > > > > > >
> > > > > > > > Fix that by adding new platform data for MT7622/7623
> > > > > > > > declaring the
> > > > > > > > right {proc,sram}_max_volt parameter.
> > > > > > > >
> > > > > > > > Fixes: ead858bd128d ("cpufreq: mediatek: Move voltage
> > > > > > > > limits
> > > > > > > > to platform data")
> > > > > > > > Fixes: 6a17b3876bc8 ("cpufreq: mediatek: Refine
> > > > > > > > mtk_cpufreq_voltage_tracking()")
> > > > > > > > Signed-off-by: AngeloGioacchino Del Regno <
> > > > > > > > angelogioacchino.delregno at collabora.com>
> > > > > > > > Signed-off-by: Jia-Wei Chang <jia-wei.chang at mediatek.com>
> > > > > > > > ---
> > > > > > > > drivers/cpufreq/mediatek-cpufreq.c | 13 +++++++++++--
> > > > > > > > 1 file changed, 11 insertions(+), 2 deletions(-)
> > > > > > > >
> > > > > > > > diff --git a/drivers/cpufreq/mediatek-cpufreq.c
> > > > > > > > b/drivers/cpufreq/mediatek-cpufreq.c
> > > > > > > > index 764e4fbdd536..9a39a7ccfae9 100644
> > > > > > > > --- a/drivers/cpufreq/mediatek-cpufreq.c
> > > > > > > > +++ b/drivers/cpufreq/mediatek-cpufreq.c
> > > > > > > > @@ -693,6 +693,15 @@ static const struct
> > > > > > > > mtk_cpufreq_platform_data mt2701_platform_data = {
> > > > > > > > .ccifreq_supported = false,
> > > > > > > > };
> > > > > > > > +static const struct mtk_cpufreq_platform_data
> > > > > > > > mt7622_platform_data = {
> > > > > > > > + .min_volt_shift = 100000,
> > > > > > > > + .max_volt_shift = 200000,
> > > > > > > > + .proc_max_volt = 1360000,
> > > > > > > > + .sram_min_volt = 0,
> > > > > > > > + .sram_max_volt = 1360000,
> > > > > > >
> > > > > > > This change breaks cpufreq (with ondemand scheduler) on my
> > > > > > > BPi
> > > > > > > R64
> > > > > > > board (having MT7622AV SoC with MT6380N PMIC).
> > > > > > > ...
> > > > > > > [ 2.540091] cpufreq: __target_index: Failed to change
> > > > > > > cpu
> > > > > > > frequency: -22
> > > > > > > [ 2.556985] cpu cpu0: cpu0: failed to scale up voltage!
> > > > > > > ...
> > > > > > > (repeating a lot, every time the highest operating point is
> > > > > > > selected
> > > > > > > by the cpufreq governor)
> > > > > > >
> > > > > > > The reason is that the MT6380N doesn't support 1360000uV on
> > > > > > > the
> > > > > > > supply
> > > > > > > outputs used for SRAM and processor.
> > > > > > >
> > > > > > > As for some reason cpufreq-mediatek tries to rise the SRAM
> > > > > > > supply
> > > > > > > voltage to the maximum for a short moment (probably a side-
> > > > > > > effect of
> > > > > > > the voltage tracking algorithm), this fails because the
> > > > > > > PMIC
> > > > > > > only
> > > > > > > supports up to 1350000uV. As the highest operating point is
> > > > > > > anyway
> > > > > > > using only 1310000uV the simple fix is setting 1350000uV as
> > > > > > > the
> > > > > > > maximum
> > > > > > > instead for both proc_max_volt and sram_max_volt.
> > > > > > >
> > > > > > > A similar situation applies also for BPi R2 (MT7623NI with
> > > > > > > MT6323L
> > > > > > > PMIC), here the maximum supported voltage of the PMIC which
> > > > > > > also only
> > > > > > > supports up to 1350000uV, and the SoC having its highest
> > > > > > > operating
> > > > > > > voltage defined at 1300000uV.
> > > > > > >
> > > > > > > If all agree with the simple fix I will post a patch for
> > > > > > > that.
> > > > > > >
> > > > > > > However, to me it feels fishy to begin with that the
> > > > > > > tracking
> > > > > > > algorithm
> > > > > > > tries to rise the voltage above the highest operating point
> > > > > > > defined in
> > > > > > > device tree, see here:
> > > > > > >
> > > > > > > 6a17b3876bc830 drivers/cpufreq/mediatek-cpufreq.c (Jia-Wei
> > > > > > > Chang 2022-05-05 19:52:20 +0800
> > > > > > > 100) new_vsram
> > > > > > > = clamp(new_vproc + soc_data->min_volt_shift,
> > > > > > > 6a17b3876bc830 drivers/cpufreq/mediatek-cpufreq.c (Jia-Wei
> > > > > > > Chang 2022-05-05 19:52:20 +0800
> > > > > > > 101) soc_data->sram_min_volt,
> > > > > > > soc_data-
> > > > > > > > sram_max_volt);
> > > > > > >
> > > > > > > However, I did not investigate in depth the purpose of this
> > > > > > > initial rise and can impossibly test my modifications to
> > > > > > > the
> > > > > > > tracking algorithm on all supported SoCs.
> > > > > > >
> > > > > >
> > > > > > Thanks for actually reporting that, I don't think that
> > > > > > there's
> > > > > > any
> > > > > > valid reason why the algorithm should set a voltage higher
> > > > > > than
> > > > > > the
> > > > > > maximum votage specified in the fastest OPP.
> > > > > >
> > > > > > Anyway - the logic for the platform data of this driver is to
> > > > > > declare
> > > > > > the maximum voltage that SoC model X supports, regardless of
> > > > > > the
> > > > > > actual
> > > > > > board-specific OPPs, so that part is right; to solve this
> > > > > > issue,
> > > > > > I guess
> > > > > > that the only way is for this driver to parse the OPPs during
> > > > > > .probe()
> > > > > > and then always use in the algorithm
> > > > > >
> > > > > > vproc_max = max(proc_max_volt, opp_vproc_max);
> > > > > > vsram_max = max(sram_max_volt, vsram_vreg_max);
> > >
> > > Hi Daniel, Angelo Sir,
> > >
> > > Thanks for the issue report and suggestions.
> > >
> > > Is it possible to modify the value of proc_max_volt and
> > > sram_max_volt
> > > to 1310000 in mt7622_platform_data as the highest voltage declared
> > > in
> > > mt7622.dtsi and then give it a try?
> > >
> > > Sorry, I need someone help to check this on mt7622 since I don't
> > > have
> > > mt7622 platform..
> >
> > Unfortunately also setting proc_max_volt and sram_max_volt to 1310000
> > doesn't work:
> > [ 1.983325] cpu cpu0: cpu0: failed to scale up voltage!
> > [ 1.988621] cpufreq: __target_index: Failed to change cpu
> > frequency: -22
> > ::repeating infinitely::
> >
> > This is because in mt6380-regulator.c you can see
> > static const unsigned int ldo_volt_table1[] = {
> > 1400000, 1350000, 1300000, 1250000, 1200000, 1150000,
> > 1100000, 1050000,
> > };
> >
> > So 1310000 is not among the supported voltages but mediatek-cpufreq.c
> > will repeatedly call
> > regulator_set_voltage(sram_reg, 1310000, 1310000);
> > which will fail for obvious reasons.
> >
> > Using 1350000 for proc_max_volt and sram_max_volt like I have
> > suggested
> > as a simple work-around does work because 1350000 is among the
> > supported
> > voltages of the MT6380 regulator.
> >
> > On MT7623 the whole problem is anyway non-existent because there is
> > no
> > separate sram-supply, hence the tracking algorithm isn't used at all.
> >
>
> Exactly.
>
> For MT7622 platform data, I think it is proper to configure as:
> .proc_max_volt = 1310000,
> .sram_max_volt = 1350000, // since mt6380_vm_reg ldo only supporting
> {..., 1300000, 1350000, 1400000} as you mentioned.
Unfortunately that also doesn't work. The tracking algorithm then
apparently still tries to set unsupported voltages, I assume that
your suggestion will result in SRAM voltage being requested as
1310000uV (proc_max_volt) + 200000uV (max_step_size) = 1330000uV
which also isn't supported by the regulator.
[ 1.972654] cpu cpu0: cpu0: failed to scale up voltage!
[ 1.977951] cpufreq: __target_index: Failed to change cpu frequency: -22
[ 1.984776] cpu cpu0: cpu0: failed to scale up voltage!
[ 1.990039] cpufreq: __target_index: Failed to change cpu frequency: -22
...
With my initial suggestion to set both, proc_max_volt and sram_max_volt
to 1350000 it does work.
However, I think we are now botching around with work-arounds not
addressing the underlying problems which are that
a) the tracking algorithm initially tries to raise the SRAM voltage to
be **exactly** the minimum of proc_max_volt + max_step_size or
sram_max_volt.
b) requesting an exact voltage, ie. regulator_set_voltage(reg, X, X),
is always problematic in case of regulators only supporting a
limited set of supported voltages.
While adjusting the voltages in the SoC's platform data as a
work-around may be good enough as a hot-fix for now, imho the best
would be to re-write the tracking algorithm addressing both of the
above flaws.
> For MT7623 platform data, it is required to add a new one.
> .proc_max_volt = 1300000,
> .sram_max_volt = 0, // since no sram-supply like you said.
>
> If MT7622 and MT7623 supplied voltage issues can be fixed by above
> platform data, feel free to send the fix patch or inform me to do that.
I've introduced dedicated platform_data for MT7623 setting
proc_max_volt to 1300000, and yes, that does work.
However, on MT7623 there has not been any problem before as well.
>
> Thanks for your help! :)
>
> > >
> > > Thanks.
> > >
> > > > >
> > > > > You probably meant to write
> > > > > vproc_max = min(proc_max_volt, opp_vproc_max);
> > > > > vsram_max = min(sram_max_volt, vsram_vreg_max);
> > > > >
> > > > > right?
> > > > >
> > > >
> > > > Apparently, some of my braincells was apparently taking a break.
> > > > :-)
> > > >
> > > > Yes, I was meaning min(), not max() :-)
> > > >
> > > > Cheers!
> > > >
> > > > > >
> > > > > > Jia-Wei, can you please handle this?
> > > > > >
> > > > > > Thanks,
> > > > > > Angelo
> > > > > >
> > > >
> > > >
> > > >
More information about the linux-arm-kernel
mailing list