[PATCH v8 07/10] arm64: dts: mediatek: add ethernet support for mt8365-evk

AngeloGioacchino Del Regno angelogioacchino.delregno at collabora.com
Thu May 25 01:49:26 PDT 2023


Il 25/05/23 10:33, Alexandre Mergnat ha scritto:
> - Enable "vibr" and "vsim2" regulators to power the ethernet chip.
> 
> Tested-by: Kevin Hilman <khilman at baylibre.com>
> Signed-off-by: Alexandre Mergnat <amergnat at baylibre.com>
> ---
>   arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 48 +++++++++++++++++++++++++++++
>   1 file changed, 48 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> index 1a5769c397c2..86524cbf4354 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> @@ -88,6 +88,29 @@ optee_reserved: optee at 43200000 {
>   	};
>   };
>   
> +&ethernet {
> +	pinctrl-0 = <&ethernet_pins>;
> +	pinctrl-names = "default";
> +	phy-handle = <&eth_phy>;
> +	phy-mode = "rmii";
> +	/*
> +	 * Ethernet and HDMI (DSI0) are sharing pins.
> +	 * Only one can be enabled at a time and require the physical switch
> +	 * SW2101 to be set on LAN position
> +	 * mt6357_vibr_reg and mt6357_vsim2_reg are needed to supply ethernet
> +	 */
> +	status = "disabled";

Ouh, that's sad :-(

...but you're left with no other choice, so I agree with providing at least
the full node in case anyone wants to actually enable it by flipping the
switch on the board, so you get my

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>

Cheers!

> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		eth_phy: ethernet-phy at 0 {
> +			reg = <0>;
> +		};
> +	};
> +};
> +
>   &i2c0 {
>   	clock-frequency = <100000>;
>   	pinctrl-0 = <&i2c0_pins>;
> @@ -138,6 +161,31 @@ &mt6357_pmic {
>   };
>   
>   &pio {
> +	ethernet_pins: ethernet-pins {
> +		phy_reset_pins {
> +			pinmux = <MT8365_PIN_133_TDM_TX_DATA1__FUNC_GPIO133>;
> +		};
> +
> +		rmii_pins {
> +			pinmux = <MT8365_PIN_0_GPIO0__FUNC_EXT_TXD0>,
> +				 <MT8365_PIN_1_GPIO1__FUNC_EXT_TXD1>,
> +				 <MT8365_PIN_2_GPIO2__FUNC_EXT_TXD2>,
> +				 <MT8365_PIN_3_GPIO3__FUNC_EXT_TXD3>,
> +				 <MT8365_PIN_4_GPIO4__FUNC_EXT_TXC>,
> +				 <MT8365_PIN_5_GPIO5__FUNC_EXT_RXER>,
> +				 <MT8365_PIN_6_GPIO6__FUNC_EXT_RXC>,
> +				 <MT8365_PIN_7_GPIO7__FUNC_EXT_RXDV>,
> +				 <MT8365_PIN_8_GPIO8__FUNC_EXT_RXD0>,
> +				 <MT8365_PIN_9_GPIO9__FUNC_EXT_RXD1>,
> +				 <MT8365_PIN_10_GPIO10__FUNC_EXT_RXD2>,
> +				 <MT8365_PIN_11_GPIO11__FUNC_EXT_RXD3>,
> +				 <MT8365_PIN_12_GPIO12__FUNC_EXT_TXEN>,
> +				 <MT8365_PIN_13_GPIO13__FUNC_EXT_COL>,
> +				 <MT8365_PIN_14_GPIO14__FUNC_EXT_MDIO>,
> +				 <MT8365_PIN_15_GPIO15__FUNC_EXT_MDC>;
> +		};
> +	};
> +
>   	gpio_keys: gpio-keys-pins {
>   		pins {
>   			pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>;
> 




More information about the linux-arm-kernel mailing list