[PATCH 1/3] pinctrl: at91-pio4: Enable Push-Pull configuration

[Claudiu.Beznea at microchip.com]

On 18.05.2023 08:40, Claudiu Beznea - M18063 wrote:
> On 17.05.2023 14:54, Ryan.Wanner at microchip.com wrote:
>> From: Ryan Wanner <Ryan.Wanner at microchip.com>
>>
>> Enable push-pull configuration. Remove integer value argument from
>> open-drain configuration as it is discarded when pinconf function is
>> called from gpiolib.
> 
> AFAICT it is still taken into account when passed tough drive-open-drain DT
> property but at the moment there are no device trees using this property.

ah, ignore this as I've just saw your question about this here:
https://lore.kernel.org/all/120117b6-feda-e7aa-4f09-a126a0747388@microchip.com/

> 
>> Add push-pull do debug and get functions.
>>
>> Signed-off-by: Ryan Wanner <Ryan.Wanner at microchip.com>
>> ---
>>  drivers/pinctrl/pinctrl-at91-pio4.c | 15 +++++++++++----
>>  1 file changed, 11 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/pinctrl/pinctrl-at91-pio4.c b/drivers/pinctrl/pinctrl-at91-pio4.c
>> index 2fe40acb6a3e..3c39d62bbc3c 100644
>> --- a/drivers/pinctrl/pinctrl-at91-pio4.c
>> +++ b/drivers/pinctrl/pinctrl-at91-pio4.c
>> @@ -762,6 +762,11 @@ static int atmel_conf_pin_config_group_get(struct pinctrl_dev *pctldev,
>>  			return -EINVAL;
>>  		arg = 1;
>>  		break;
>> +	case PIN_CONFIG_DRIVE_PUSH_PULL:
>> +		if (res & ATMEL_PIO_OPD_MASK)
>> +			return -EINVAL;
>> +		arg = 1;
>> +		break;
>>  	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
>>  		if (!(res & ATMEL_PIO_SCHMITT_MASK))
>>  			return -EINVAL;
>> @@ -827,10 +832,10 @@ static int atmel_conf_pin_config_group_set(struct pinctrl_dev *pctldev,
>>  			conf &= (~ATMEL_PIO_PUEN_MASK);
>>  			break;
>>  		case PIN_CONFIG_DRIVE_OPEN_DRAIN:
>> -			if (arg == 0)
>> -				conf &= (~ATMEL_PIO_OPD_MASK);
>> -			else
>> -				conf |= ATMEL_PIO_OPD_MASK;
>> +			conf |= ATMEL_PIO_OPD_MASK;
>> +			break;
>> +		case PIN_CONFIG_DRIVE_PUSH_PULL:
>> +			conf &= (~ATMEL_PIO_OPD_MASK);
>>  			break;
>>  		case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
>>  			if (arg == 0)
>> @@ -948,6 +953,8 @@ static void atmel_conf_pin_config_dbg_show(struct pinctrl_dev *pctldev,
>>  		seq_printf(s, "%s ", "debounce");
>>  	if (conf & ATMEL_PIO_OPD_MASK)
>>  		seq_printf(s, "%s ", "open-drain");
>> +	if (!(conf & ATMEL_PIO_OPD_MASK))
> 
> else would fit better here.
> 
>> +		seq_printf(s, "%s ", "push-pull");
>>  	if (conf & ATMEL_PIO_SCHMITT_MASK)
>>  		seq_printf(s, "%s ", "schmitt");
>>  	if (atmel_pioctrl->slew_rate_support && (conf & ATMEL_PIO_SR_MASK))
>