[PATCH 0/6] arm64: errata: Disable FWB on parts with non-ARM interconnects

[James Morse]

Hi Catalin, Marc,

On 11/05/2023 22:13, Catalin Marinas wrote:
> On Thu, May 11, 2023 at 07:42:58PM +0100, Marc Zyngier wrote:
>> On Thu, 11 May 2023 18:15:15 +0100,
>> Catalin Marinas <catalin.marinas at arm.com> wrote:
>>> On Thu, Mar 30, 2023 at 05:51:22PM +0100, James Morse wrote:
>>>> When stage1 translation is disabled, the SCTRL_E1.I bit controls the
>>>> attributes used for instruction fetch, one of the options results in a
>>>> non-cacheable access. A whole host of CPUs missed the FWB override
>>>> in this case, meaning a KVM guest could fetch stale/junk data instead of
>>>> instructions.
>>>>
>>>> The workaround is to disable FWB, and do the required cache maintenance
>>>> instead.

>>> I think the workaround can be to only do the required cache maintenance
>>> without disabling FWB. Having FWB on doesn't bring any performance
>>> benefits if we do the cache maintenance anyway but keeping it around may
>>> be useful for other reasons (e.g. KVM device pass-through using
>>> cacheable mappings, though not something KVM supports currently).
>>
>> But you'd also rely on the guest doing its own cache maintenance for
>> instructions it writes, right?
> 
> Ah, you are right. It looks like I only considered the host writing
> instructions. If the guest disabled stage 1 and wrote some instructions
> with FWB on, they'd not necessarily reach the PoC while the instructions
> are fetched from PoC with this bug. Even with SCTLR_EL1.I==0, the guest
> is supposed to do an IC IVAU if it wrote instructions but that's not
> sufficient (hint to the micro-architects, add a chicken bit to upgrade
> IC IVAU to also do a DC CVAC ;))
> 
>> Which probably means exposing a different CLIDR_EL1 so that
>> LoC/LoUU/LoUIS are consistent with *not* having FWB... I also wonder
>> if keeping FWB set has the potential to change the semantics of the
>> CMOs (the spec seems silent on that front).
> 
> Not sure about CMOs, I'd expect them to behave in the same way. However,
> I don't see how faking CLIDR_EL1 can trick the guest into doing DC CVAC
> when its MMU is off.

I think the request is to keep the FWB feature, but to disable it for all host memory
the guest can execute from. I presume this 'device pass-through using cacheable mappings'
would mark that address range as XN at stage2, ( ... it's special right?).

If this is for something like CXL: it can't set XN, and the guest would still be exposed
to the erratum if it executes from theses addresses with the MMU off.

Does this need doing now? It wouldn't need backporting to older kernels...


>>> That said, maybe we can reduce the risk further by doing the
>>> vcpu_has_run_once() trick with !FWB and clean the D side to PoC on a
>>> stage 2 exec fault (together with the I-cache invalidation). We can then
>>> ignore any other cache maintenance on S2 faults until someone shouts (we
>>> can maybe recommend forcing FWB off on the command line through the
>>> cpuid override).
>>
>> You lost me here with your vcpu_has_run_once().
> 
> Most likely I lost myself in the code. So the tricks we used in the past
> tracking the guest MMU off/on was only for the D side. If (we hope that)
> the guest only wrote instructions to a page once before executing them
> (and never writing instructions again), we could trap a subsequent exec
> fault and do the D-cache clean to PoC again.
> 
>> Keeping the CMOs on exec fault is definitely manageable. But is that
>> enough?
> 
> Yeah, not sure it's enough if the guest keeps writing instructions to
> the same page with the MMU off.

The difference between FWB and IDC/DIC still does my head in: My reading is FWB implies
IDC, (but the CTR_EL0.IDC bit might not be set). This doesn't help if the wrong attributes
are being used for instruction fetch.
This is cache-maintenance that wasn't needed before, so there are no tricks with the id
registers we can pull to make the guest do it.


v2 of this will flip the polarity, and also detect based on an 'arm,interconnect'
compatible, or the existing compatible the PMU driver uses.



Thanks,

James