[PATCH 2/2] arm64: dts: freescale: Add imx8mp-venice-gw7905-2x

[Krzysztof Kozlowski]

On 11/05/2023 19:10, Tim Harvey wrote:
> The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.
> 
> The GW702x SOM contains the following:
>  - i.MX8M Plus SoC
>  - LPDDR4 memory
>  - eMMC Boot device
>  - Gateworks System Controller (GSC) with integrated EEPROM, button
>    controller, and ADC's
>  - PMIC
>  - RGMII PHY (eQoS)
>  - SOM connector providing:
>   - eQoS GbE MII
>   - 1x SPI
>   - 2x I2C
>   - 4x UART
>   - 2x USB 3.0
>   - 1x PCI
>   - 1x SDIO (4-bit 3.3V)
>   - 1x SDIO (4-bit 3.3V/1.8V)
>   - GPIO
> 
> The GW7905 Baseboard contains the following:
>  - GPS
>  - microSD
>  - off-board I/O connector with I2C, SPI, GPIO
>  - EERPOM
>  - PCIe clock generator
>  - 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
>  - 1x half-length miniPCIe socket with USB2.0 and USB3.0
>  - USB 3.0 HUB
>  - USB Type-C with USB PD Sink capability and peripheral support
>  - USB Type-C with USB 3.0 host support
> 
> Signed-off-by: Tim Harvey <tharvey at gateworks.com>
> ---
>  .../dts/freescale/imx8mp-venice-gw702x.dtsi   | 589 ++++++++++++++++++
>  .../dts/freescale/imx8mp-venice-gw7905-2x.dts |  28 +
>  .../dts/freescale/imx8mp-venice-gw7905.dtsi   | 358 +++++++++++


How do you compile it? Missing Makefile. This also suggests that maybe
you did not test it with dtbs_check...


>  3 files changed, 975 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw702x.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi

...

> +	gsc: gsc at 20 {
> +		compatible = "gw,gsc";
> +		reg = <0x20>;
> +		pinctrl-0 = <&pinctrl_gsc>;
> +		interrupt-parent = <&gpio2>;
> +		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		adc {
> +			compatible = "gw,gsc-adc";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			channel at 6 {
> +				gw,mode = <0>;
> +				reg = <0x06>;
> +				label = "temp";
> +			};
> +
> +			channel at 8 {
> +				gw,mode = <1>;
> +				reg = <0x08>;
> +				label = "vdd_bat";
> +			};
> +
> +			channel at 16 {
> +				gw,mode = <4>;
> +				reg = <0x16>;
> +				label = "fan_tach";
> +			};
> +
> +			channel at 82 {
> +				gw,mode = <2>;
> +				reg = <0x82>;
> +				label = "vdd_vin";
> +				gw,voltage-divider-ohms = <22100 1000>;
> +			};
> +
> +			channel at 84 {
> +				gw,mode = <2>;
> +				reg = <0x84>;
> +				label = "vdd_adc1";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +
> +			channel at 86 {
> +				gw,mode = <2>;
> +				reg = <0x86>;
> +				label = "vdd_adc2";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +
> +			channel at 88 {
> +				gw,mode = <2>;
> +				reg = <0x88>;
> +				label = "vdd_1p0";
> +			};
> +
> +			channel at 8c {
> +				gw,mode = <2>;
> +				reg = <0x8c>;
> +				label = "vdd_1p8";
> +			};
> +
> +			channel at 8e {
> +				gw,mode = <2>;
> +				reg = <0x8e>;
> +				label = "vdd_2p5";
> +			};
> +
> +			channel at 90 {
> +				gw,mode = <2>;
> +				reg = <0x90>;
> +				label = "vdd_3p3";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +
> +			channel at 92 {
> +				gw,mode = <2>;
> +				reg = <0x92>;
> +				label = "vdd_dram";
> +			};
> +
> +			channel at 98 {
> +				gw,mode = <2>;
> +				reg = <0x98>;
> +				label = "vdd_soc";
> +			};
> +
> +			channel at 9a {
> +				gw,mode = <2>;
> +				reg = <0x9a>;
> +				label = "vdd_arm";
> +			};
> +
> +			channel at a2 {
> +				gw,mode = <2>;
> +				reg = <0xa2>;
> +				label = "vdd_gsc";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +		};
> +
> +		fan-controller at 0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;

Why do you need these two? I know binding expects them, but why? Anyway
compatible is first, reg is second property.


> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
> new file mode 100644
> index 000000000000..4a1bbbbe19e6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
> @@ -0,0 +1,28 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2023 Gateworks Corporation
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mp.dtsi"
> +#include "imx8mp-venice-gw702x.dtsi"
> +#include "imx8mp-venice-gw7905.dtsi"
> +
> +/ {
> +	model = "Gateworks Venice GW7905-2x i.MX8MP Development Kit";
> +	compatible = "gateworks,imx8mp-gw7905-2x", "fsl,imx8mp";
> +
> +	chosen {
> +		stdout-path = &uart2;
> +	};
> +};
> +
> +/* Disable SOM interfaces not used on baseboard */
> +&eqos {
> +	status = "disabled";
> +};
> +
> +&usdhc1 {
> +	status = "disabled";
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi
> new file mode 100644
> index 000000000000..479190a6391f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi
> @@ -0,0 +1,358 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2023 Gateworks Corporation
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/phy/phy-imx8-pcie.h>
> +
> +/ {
> +	aliases {
> +		ethernet0 = &eqos;
> +	};
> +
> +	led-controller {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> +		led-0 {
> +			function = LED_FUNCTION_STATUS;
> +			color = <LED_COLOR_ID_GREEN>;
> +			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +		led-1 {
> +			function = LED_FUNCTION_STATUS;
> +			color = <LED_COLOR_ID_RED>;
> +			gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	pcie0_refclk: pcie0-refclk {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <100000000>;
> +	};
> +
> +	pps {
> +		compatible = "pps-gpio";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pps>;
> +		gpios = <&gpio4 21 GPIO_ACTIVE_HIGH>;
> +		status = "okay";
> +	};
> +
> +	reg_usb2_vbus: regulator-usb2-vbus {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_usb2_en>;
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb2_vbus";
> +		gpio = <&gpio4 12 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	reg_usdhc2_vmmc: regulator-usdhc2 {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> +		compatible = "regulator-fixed";
> +		regulator-name = "SD2_3P3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +

Drop stay blank line

> +};
> +
> +/* off-board header */
> +&ecspi2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_spi2>;
> +	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +};



Best regards,
Krzysztof