[PATCH v2 2/3] usb: chipidea: imx: support disabling runtime-pm

[Jun Li]

> -----Original Message-----
> From: Francesco Dolcini <francesco at dolcini.it>
> Sent: Monday, May 8, 2023 7:17 PM
> To: Jun Li <jun.li at nxp.com>
> Cc: Francesco Dolcini <francesco at dolcini.it>; Luca Ceresoli
> <luca.ceresoli at bootlin.com>; devicetree at vger.kernel.org;
> festevam at gmail.com; gregkh at linuxfoundation.org; kernel at pengutronix.de;
> linux-arm-kernel at lists.infradead.org; dl-linux-imx <linux-imx at nxp.com>;
> linux-kernel at vger.kernel.org; linux-usb at vger.kernel.org;
> robh+dt at kernel.org; s.hauer at pengutronix.de; shawnguo at kernel.org;
> Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>; Francesco Dolcini
> <francesco.dolcini at toradex.com>; Xu Yang <xu.yang_2 at nxp.com>
> Subject: Re: [PATCH v2 2/3] usb: chipidea: imx: support disabling runtime-pm
> 
> On Sat, May 06, 2023 at 09:02:39AM +0000, Jun Li wrote:
> > > -----Original Message-----
> > > From: Francesco Dolcini <francesco at dolcini.it>
> > > Sent: Friday, May 5, 2023 7:00 PM
> > > To: Luca Ceresoli <luca.ceresoli at bootlin.com>; Jun Li <jun.li at nxp.com>
> > > Cc: Francesco Dolcini <francesco at dolcini.it>;
> devicetree at vger.kernel.org;
> > > festevam at gmail.com; gregkh at linuxfoundation.org;
> kernel at pengutronix.de;
> > > linux-arm-kernel at lists.infradead.org; dl-linux-imx
> <linux-imx at nxp.com>;
> > > linux-kernel at vger.kernel.org; linux-usb at vger.kernel.org;
> > > peter.chen at nxp.com; robh+dt at kernel.org; s.hauer at pengutronix.de;
> > > shawnguo at kernel.org; Krzysztof Kozlowski
> <krzysztof.kozlowski at linaro.org>;
> > > Francesco Dolcini <francesco.dolcini at toradex.com>
> > > Subject: Re: [PATCH v2 2/3] usb: chipidea: imx: support disabling
> runtime-pm
> > >
> > > On Fri, May 05, 2023 at 12:06:18PM +0200, Luca Ceresoli wrote:
> > > > On Fri, 5 May 2023 09:49:16 +0000
> > > > Jun Li <jun.li at nxp.com> wrote:
> > > > > Is your board design similar like Francesco's as below?
> > > >
> > > > Possibly, but I'm afraid I can't say: I am using the Toradex Colibri
> > > > i.MX6ULL SoM, whose schematics are not public.
> > >
> > > I can confirm that it's the same.
> >
> > Thanks Francesco for the confirmation, had a check with design team,
> > there is no status bit which can be used to judge the VDD_USB_CAP is
> > powered or not, so we have to add a board level dts property to tell
> > this usb phy driver to bypass MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS.
> >
> > Before send a formal patch, I want to confirm this should work for your
> > HW design, like below simple hack:
> 
> Thanks Li Jun, I tested it with v6.3.1 kernel and it's all good.
> I would be happy to test the patch as soon as you send it.
> 
> 
> With that said I had another issue that I assume is unrelated.
> In addition to the USB Host port, we have an additional OTG one. This
> interface has the same circuit WRT to the VBUS, however in this case
> it's possible to read the VBUS using extcon, e.g. a standard GPIO input.
> 
> With that setup, while doing a role switch, I had a couple of time this
> error:
> 
> [  187.310421] ci_hdrc ci_hdrc.0: USB bus 2 deregistered
> [  192.351452] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in OTGSC
> 
> that was recovered only doing an additional transition.
> 
> More complete logs here:
> 
> [  184.997619] usb 2-1: USB disconnect, device number 9
> [  185.019620] ci_hdrc ci_hdrc.0: remove, state 1
> [  185.024271] usb usb2: USB disconnect, device number 1
> [  185.334975] ci_hdrc ci_hdrc.0: USB bus 2 deregistered
> [  185.353857] ci_hdrc ci_hdrc.0: EHCI Host Controller
> [  185.389670] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number
> 2
> [  185.470170] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
> [  185.476097] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002,
> bcdDevice= 6.01
> [  185.484527] usb usb2: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [  185.491811] usb usb2: Product: EHCI Host Controller
> [  185.496704] usb usb2: Manufacturer: Linux 6.1.22-6.2.0+git.3b29299e5f60
> ehci_hcd
> [  185.504148] usb usb2: SerialNumber: ci_hdrc.0
> [  185.531121] hub 2-0:1.0: USB hub found
> [  185.542636] hub 2-0:1.0: 1 port detected
> [  185.556586] mxs_phy 20c9000.usbphy: vbus is not valid
> [  187.271684] ci_hdrc ci_hdrc.0: remove, state 4
> [  187.276281] usb usb2: USB disconnect, device number 1
> [  187.310421] ci_hdrc ci_hdrc.0: USB bus 2 deregistered
> [  192.351452] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in OTGSC

I have 2 questions:
1. Can your OTG port work fine in device/gadget mode if you did not
   do usb role switch?(e.g. the OTG port *never* switch to host mode
   after system boot).
2. Please show me your dts file node of your USB OTG port, I want to
   Know how you config your OTG port. 

Thanks
Li Jun
> 
> 
> > diff --git a/drivers/usb/phy/phy-mxs-usb.c
> b/drivers/usb/phy/phy-mxs-usb.c
> > index e1a2b2ea098b..ec5ee790455e 100644
> > --- a/drivers/usb/phy/phy-mxs-usb.c
> > +++ b/drivers/usb/phy/phy-mxs-usb.c
> > @@ -178,7 +178,6 @@ static const struct mxs_phy_data imx6sx_phy_data =
> {
> >  };
> >
> >  static const struct mxs_phy_data imx6ul_phy_data = {
> > -       .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS,
> >  };
> >
> >  static const struct mxs_phy_data imx7ulp_phy_data = {
> 
> Francesco