[PATCH v9 09/10] ARM: dts: stm32: add STM32MP1-based Phytec SoM
Steffen Trumtrar
s.trumtrar at pengutronix.de
Thu May 4 23:01:57 PDT 2023
The Phytec STM32MP1 based SoMs feature up to 1 GB DDR3LP RAM, up to 1 GB
eMMC, up to 16 MB QSPI and up to 128 GB NAND flash.
Signed-off-by: Steffen Trumtrar <s.trumtrar at pengutronix.de>
---
Notes:
Changes since v7:
- remove unused gpu_reservde memory range
- get rid of duplicate ethernet clock assignments
Changes since v6:
- rename mdio0->mdio
Changes since v5:
- cleanup dt_bindings_check warnings
Changes since v4:
- cleanup usage of "status = okay|disabled"
- fix remaining non-generic node names
- rework sai nodes to not duplicate the existing settings in stm32mp151.dtsi
Changes since v3:
- cleanup board-compatible
- cleanup aliases
- rename nodes according to schema
- use interrupt flag
.../stm32mp157c-phycore-stm32mp15-som.dtsi | 577 ++++++++++++++++++
1 file changed, 577 insertions(+)
create mode 100644 arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
diff --git a/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi b/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
new file mode 100644
index 000000000000..4e8b2d2b30c7
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
@@ -0,0 +1,577 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022-2023 Steffen Trumtrar <kernel at pengutronix.de>
+ * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
+ * Author: Dom VOVARD <dom.vovard at linrt.com>.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "stm32mp15-pinctrl.dtsi"
+
+/ {
+ model = "PHYTEC phyCORE-STM32MP15 SOM";
+ compatible = "phytec,phycore-stm32mp157c-som", "st,stm32mp157";
+
+ aliases {
+ ethernet0 = ðernet0;
+ rtc0 = &i2c4_rtc;
+ rtc1 = &rtc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ key-home {
+ label = "Home";
+ gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOME>;
+ };
+
+ key-enter {
+ label = "Enter";
+ gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_ENTER>;
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ retram: retram at 38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+
+ mcuram: mcuram at 30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ mcuram2: mcuram2 at 10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0 at 10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1 at 10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer at 10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+ };
+
+ sound {
+ compatible = "audio-graph-card";
+ label = "STM32MP1-PHYCORE";
+ routing =
+ "Playback", "MCLK", /* Set a route between "MCLK" and "playback" widgets */
+ "Capture", "MCLK";
+ dais = <&sai2b_port>,
+ <&sai2a_port>;
+ };
+
+ regulator_vin: regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vin";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+};
+
+ðernet0 {
+ pinctrl-0 = <ðernet0_rgmii_pins_d>;
+ pinctrl-1 = <ðernet0_rgmii_sleep_pins_d>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+ st,eth-clk-sel;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+
+ phy0: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ interrupt-parent = <&gpiog>;
+ interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ enet-phy-lane-no-swap;
+ ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_b>;
+ pinctrl-1 = <&i2c1_sleep_pins_b>;
+ i2c-scl-rising-time-ns = <100>;
+ i2c-scl-falling-time-ns = <7>;
+ status = "okay";
+
+ codec at 18 {
+ compatible = "ti,tlv320aic3007";
+ reg = <0x18>;
+ #sound-dai-cells = <0>;
+
+ ai3x-micbias-vg = <2>;
+
+ AVDD-supply = <&v3v3>;
+ IOVDD-supply = <&v3v3>;
+ DRVDD-supply = <&v3v3>;
+ DVDD-supply = <&v1v8_audio>;
+
+ clocks = <&sai2b>;
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tlv320_tx_endpoint: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&sai2b_endpoint>;
+ frame-master;
+ bitclock-master;
+ };
+
+ tlv320_rx_endpoint: endpoint at 1 {
+ reg = <1>;
+ remote-endpoint = <&sai2a_endpoint>;
+ frame-master;
+ bitclock-master;
+ };
+ };
+ };
+
+ touch at 44 {
+ compatible = "st,stmpe811";
+ reg = <0x44>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpioi>;
+ vio-supply = <&v3v3>;
+ vcc-supply = <&v3v3>;
+
+ touchscreen {
+ compatible = "st,stmpe-ts";
+ st,sample-time = <4>;
+ st,mod-12b = <1>;
+ st,ref-sel = <0>;
+ st,adc-freq = <1>;
+ st,ave-ctrl = <1>;
+ st,touch-det-delay = <2>;
+ st,settling = <2>;
+ st,fraction-z = <7>;
+ st,i-drive = <1>;
+ };
+ };
+
+ leds at 62 {
+ compatible = "nxp,pca9533";
+ reg = <0x62>;
+
+ led-0 {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_POWER;
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_POWER;
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led-2 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_HEARTBEAT;
+ type = <PCA9532_TYPE_LED>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c4_pins_a>;
+ pinctrl-1 = <&i2c4_sleep_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+
+ pmic at 33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+ buck1-supply = <®ulator_vin>;
+ buck2-supply = <®ulator_vin>;
+ buck3-supply = <®ulator_vin>;
+ buck4-supply = <®ulator_vin>;
+ ldo1-supply = <&v3v3>;
+ ldo2-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo4-supply = <®ulator_vin>;
+ ldo5-supply = <&v3v3>;
+ ldo6-supply = <&v3v3>;
+ boost-supply = <®ulator_vin>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask-reset;
+ regulator-initial-mode = <0>;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ };
+
+ v1v8_audio: ldo1 {
+ regulator-name = "v1v8_audio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO1 0>;
+
+ };
+
+ vdd_eth_2v5: ldo2 {
+ regulator-name = "dd_eth_2v5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO2 0>;
+
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdda: ldo5 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ vdd_eth_1v0: ldo6 {
+ regulator-name = "vdd_eth_1v0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO6 0>;
+
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ regulator-active-discharge = <1>;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge = <1>;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>,
+ <IT_PONKEY_R 0>;
+ interrupt-names = "onkey-falling",
+ "onkey-rising";
+ power-off-time-sec = <10>;
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ };
+ };
+
+ i2c4_eeprom: eeprom at 50 {
+ compatible = "microchip,24c32",
+ "atmel,24c32";
+ reg = <0x50>;
+ };
+
+ i2c4_rtc: rtc at 52 {
+ compatible = "microcrystal,rv3028";
+ reg = <0x52>;
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&m_can2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&m_can2_pins_a>;
+ pinctrl-1 = <&m_can2_sleep_pins_a>;
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+ mbox-names = "vq0", "vq1", "shutdown", "detach";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "okay";
+};
+
+&pwr_regulators {
+ vdd-supply = <&vdd>;
+ vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+ pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+ status = "okay";
+
+ flash0: flash at 0 {
+ compatible = "winbond,w25q128", "jedec,spi-nor";
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sai2 {
+ clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+ clock-names = "pclk", "x8k", "x11k";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sai2a_pins_b>, <&sai2b_pins_d>;
+ pinctrl-1 = <&sai2a_sleep_pins_b>, <&sai2b_sleep_pins_d>;
+ status = "okay";
+};
+
+&sai2a {
+ dma-names = "rx";
+ st,sync = <&sai2b 2>;
+ clocks = <&rcc SAI2_K>, <&sai2b>;
+ clock-names = "sai_ck", "MCLK";
+ #clock-cells = <0>;
+
+ sai2a_port: port {
+ sai2a_endpoint: endpoint {
+ remote-endpoint = <&tlv320_rx_endpoint>;
+ mclk-fs = <256>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <16>;
+ };
+ };
+};
+
+&sai2b {
+ dma-names = "tx";
+ #clock-cells = <0>;
+
+ sai2b_port: port {
+ sai2b_endpoint: endpoint {
+ remote-endpoint = <&tlv320_tx_endpoint>;
+ mclk-fs = <256>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <16>;
+ };
+ };
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_b>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_b>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_b>;
+ cd-gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_e>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_e>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_e>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+ bus-width = <8>;
+ vmmc-supply = <&v3v3>;
+ vqmmc-supply = <&v3v3>;
+ mmc-ddr-3_3v;
+};
+
+&spi1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi1_pins_a>;
+ pinctrl-1 = <&spi1_sleep_pins_a>;
+ cs-gpios = <&gpioz 3 0>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default", "sleep", "idle";
+ pinctrl-0 = <&uart4_pins_a>;
+ pinctrl-1 = <&uart4_sleep_pins_a>;
+ pinctrl-2 = <&uart4_idle_pins_a>;
+ pinctrl-3 = <&uart4_pins_a>;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
+
+&usart1 {
+ pinctrl-names = "default", "sleep", "idle";
+ pinctrl-0 = <&usart1_pins_b &usart1_pins_a>;
+ pinctrl-1 = <&usart1_sleep_pins_b &usart1_sleep_pins_a>;
+ pinctrl-2 = <&usart1_idle_pins_b &usart1_idle_pins_a>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usart3 {
+ pinctrl-names = "default", "sleep", "idle";
+ pinctrl-0 = <&usart3_pins_a>;
+ pinctrl-1 = <&usart3_sleep_pins_a>;
+ pinctrl-2 = <&usart3_idle_pins_a>;
+ status = "okay";
+};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+&usbh_ohci {
+ phys = <&usbphyc_port0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+&usbotg_hs {
+ phys = <&usbphyc_port1 0>;
+ phy-names = "usb2-phy";
+ status = "okay";
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+};
--
2.39.1
More information about the linux-arm-kernel
mailing list