[PATCH 2/2] arm64: dts: ti: Add basic support for phyBOARD-Lyra-AM625
Nishanth Menon
nm at ti.com
Thu May 4 07:26:43 PDT 2023
On 16:01-20230504, Wadim Egorov wrote:
> The phyCORE-AM62x [1] is a SoM (System on Module) featuring TI's AM62x SoC.
> It can be used in combination with different carrier boards.
> This module can come with different sizes and models for
> DDR, eMMC, SPI NOR Flash and various SoCs from the AM62x family.
>
> A development Kit, called phyBOARD-Lyra [2] is used as a carrier board
> reference design around the AM62x SoM.
>
> Supported features:
> * Debug UART
> * SPI NOR Flash
> * eMMC
> * 2x Ethernet
> * Micro SD card
> * I2C EEPROM
> * I2C RTC
> * GPIO Expander
> * LEDs
> * USB
>
> For more details, see:
>
> [1] Product page SoM: https://www.phytec.com/product/phycore-am62x
> [2] Product page CB: https://www.phytec.com/product/phyboard-am62x
>
> Signed-off-by: Wadim Egorov <w.egorov at phytec.de>
> ---
> arch/arm64/boot/dts/ti/Makefile | 1 +
> .../boot/dts/ti/k3-am62-phycore-som.dtsi | 324 ++++++++++++++++++
> .../dts/ti/k3-am625-phyboard-lyra-rdk.dts | 267 +++++++++++++++
Just wondering: if the carrier board can easily work with different
SoMs.. in which case, we could do overlay to create the som + carrier
overlay to create rdk dtb - this might allow the scheme to scale to
additional SoMs and carrier combinations.. and the SoM dtb could be
sufficient for something like a bootloader.
> 3 files changed, 592 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi
> create mode 100644 arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index c83c9d772b81..9388dc481d7d 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -10,6 +10,7 @@
>
> # Boards with AM62x SoC
> dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am625-phyboard-lyra-rdk.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am62-lp-sk.dtb
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi
> new file mode 100644
> index 000000000000..32264296c8c6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi
> @@ -0,0 +1,324 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2022 - 2023 PHYTEC Messtechnik GmbH
> + * Author: Wadim Egorov <w.egorov at phytec.de>
> + *
> + * Product homepage:
> + * https://www.phytec.com/product/phycore-am62x
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/ {
> + model = "PHYTEC phyCORE-AM62x";
> + compatible = "phytec,am62-phycore-som", "ti,am625";
> +
> + aliases {
> + ethernet0 = &cpsw_port1;
> + gpio0 = &main_gpio0;
> + gpio1 = &main_gpio1;
> + i2c0 = &main_i2c0;
> + mmc0 = &sdhci0;
> + rtc0 = &i2c_som_rtc;
> + rtc1 = &wkup_rtc0;
> + spi0 = &ospi0;
> + };
> +
> + memory at 80000000 {
> + device_type = "memory";
> + reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
> + };
> +
> + reserved_memory: reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + ramoops at 9ca00000 {
> + compatible = "ramoops";
> + reg = <0x00 0x9ca00000 0x00 0x00100000>;
> + record-size = <0x8000>;
> + console-size = <0x8000>;
> + ftrace-size = <0x00>;
> + pmsg-size = <0x8000>;
> + };
> +
> + secure_tfa_ddr: tfa at 9e780000 {
> + reg = <0x00 0x9e780000 0x00 0x80000>;
> + alignment = <0x1000>;
> + no-map;
> + };
> +
> + secure_ddr: optee at 9e800000 {
> + reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
> + alignment = <0x1000>;
> + no-map;
> + };
> +
> + wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory at 9db00000 {
> + compatible = "shared-dma-pool";
> + reg = <0x00 0x9db00000 0x00 0x00c00000>;
> + no-map;
> + };
> + };
> +
> + vcc_5v0_som: regulator-vcc-5v0-som {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_5V0_SOM";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vdd_1v8: regulator-vdd-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDD_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_5v0_som>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&leds_pins_default>;
> +
> + led-0 {
> + color = <LED_COLOR_ID_GREEN>;
> + gpios = <&main_gpio0 13 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + function = LED_FUNCTION_HEARTBEAT;
> + };
> + };
> +};
> +
> +&main_pmx0 {
> + leds_pins_default: leds-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x034, PIN_OUTPUT, 7) /* (H21) OSPI0_CSN2.GPIO0_13 */
> + >;
> + };
> +
> + main_i2c0_pins_default: main-i2c0-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
> + AM62X_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
> + >;
> + };
> +
> + main_mdio1_pins_default: main_mdio1-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
> + AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
> + >;
> + };
> +
> + main_mmc0_pins_default: main-mmc0-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (Y3) MMC0_CMD */
> + AM62X_IOPAD(0x218, PIN_INPUT_PULLDOWN, 0) /* (AB1) MMC0_CLK */
> + AM62X_IOPAD(0x214, PIN_INPUT_PULLUP, 0) /* (AA2) MMC0_DAT0 */
> + AM62X_IOPAD(0x210, PIN_INPUT_PULLUP, 0) /* (AA1) MMC0_DAT1 */
> + AM62X_IOPAD(0x20c, PIN_INPUT_PULLUP, 0) /* (AA3) MMC0_DAT2 */
> + AM62X_IOPAD(0x208, PIN_INPUT_PULLUP, 0) /* (Y4) MMC0_DAT3 */
> + AM62X_IOPAD(0x204, PIN_INPUT_PULLUP, 0) /* (AB2) MMC0_DAT4 */
> + AM62X_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (AC1) MMC0_DAT5 */
> + AM62X_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (AD2) MMC0_DAT6 */
> + AM62X_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */
> + >;
> + };
> +
> + main_rgmii1_pins_default: main-rgmii1-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x14c, PIN_INPUT, 0) /* (AB17) RGMII1_RD0 */
> + AM62X_IOPAD(0x150, PIN_INPUT, 0) /* (AC17) RGMII1_RD1 */
> + AM62X_IOPAD(0x154, PIN_INPUT, 0) /* (AB16) RGMII1_RD2 */
> + AM62X_IOPAD(0x158, PIN_INPUT, 0) /* (AA15) RGMII1_RD3 */
> + AM62X_IOPAD(0x148, PIN_INPUT, 0) /* (AD17) RGMII1_RXC */
> + AM62X_IOPAD(0x144, PIN_INPUT, 0) /* (AE17) RGMII1_RX_CTL */
> + AM62X_IOPAD(0x134, PIN_OUTPUT, 0) /* (AE20) RGMII1_TD0 */
> + AM62X_IOPAD(0x138, PIN_OUTPUT, 0) /* (AD20) RGMII1_TD1 */
> + AM62X_IOPAD(0x13c, PIN_OUTPUT, 0) /* (AE18) RGMII1_TD2 */
> + AM62X_IOPAD(0x140, PIN_OUTPUT, 0) /* (AD18) RGMII1_TD3 */
> + AM62X_IOPAD(0x130, PIN_OUTPUT, 0) /* (AE19) RGMII1_TXC */
> + AM62X_IOPAD(0x12c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */
> + >;
> + };
> +
> + ospi0_pins_default: ospi0-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
> + AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
> + AM62X_IOPAD(0x00c, PIN_INPUT, 0) /* (E25) OSPI0_D0 */
> + AM62X_IOPAD(0x010, PIN_INPUT, 0) /* (G24) OSPI0_D1 */
> + AM62X_IOPAD(0x014, PIN_INPUT, 0) /* (F25) OSPI0_D2 */
> + AM62X_IOPAD(0x018, PIN_INPUT, 0) /* (F24) OSPI0_D3 */
> + AM62X_IOPAD(0x01c, PIN_INPUT, 0) /* (J23) OSPI0_D4 */
> + AM62X_IOPAD(0x020, PIN_INPUT, 0) /* (J25) OSPI0_D5 */
> + AM62X_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */
> + AM62X_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
> + AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
> + >;
> + };
> +
> + pmic_irq_pins_default: pmic-irq-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x01f4, PIN_INPUT, 0) /* (D16) EXTINTn */
> + >;
> + };
> +};
> +
> +&cpsw3g {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_rgmii1_pins_default>;
> +};
> +
> +&cpsw_port1 {
> + phy-mode = "rgmii-rxid";
> + phy-handle = <&cpsw3g_phy1>;
> +};
> +
> +&cpsw3g_mdio {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mdio1_pins_default>;
> + status = "okay";
> +
> + cpsw3g_phy1: ethernet-phy at 1 {
> + compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + };
> +};
> +
> +&main_i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c0_pins_default>;
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + pmic at 30 {
> + compatible = "ti,tps65219";
> + reg = <0x30>;
> + buck1-supply = <&vcc_5v0_som>;
> + buck2-supply = <&vcc_5v0_som>;
> + buck3-supply = <&vcc_5v0_som>;
> + ldo1-supply = <&vdd_3v3>;
> + ldo2-supply = <&vdd_1v8>;
> + ldo3-supply = <&vcc_5v0_som>;
> + ldo4-supply = <&vcc_5v0_som>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_irq_pins_default>;
> + interrupt-parent = <&gic500>;
> + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + ti,power-button;
> + system-power-controller;
> +
> + regulators {
> + vdd_core: buck1 {
> + regulator-name = "VDD_CORE";
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd_3v3: buck2 {
> + regulator-name = "VDD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd_ddr4: buck3 {
> + regulator-name = "VDD_DDR4";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vddshv5_sdio: ldo1 {
> + regulator-name = "VDDSHV5_SDIO";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-allow-bypass;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vddr_core: ldo2 {
> + regulator-name = "VDDR_CORE";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdda_1v8: ldo3 {
> + regulator-name = "VDDA_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd_2v5: ldo4 {
> + regulator-name = "VDD_2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +
> + eeprom at 50 {
> + compatible = "atmel,24c32";
> + pagesize = <32>;
> + reg = <0x50>;
> + };
> +
> + i2c_som_rtc: rtc at 52 {
> + compatible = "microcrystal,rv3028";
> + reg = <0x52>;
> + };
> +};
> +
> +&ospi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ospi0_pins_default>;
> + status = "okay";
> +
> + serial_flash: flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-tx-bus-width = <8>;
> + spi-rx-bus-width = <8>;
> + spi-max-frequency = <25000000>;
> + cdns,tshsl-ns = <60>;
> + cdns,tsd2d-ns = <60>;
> + cdns,tchsh-ns = <60>;
> + cdns,tslch-ns = <60>;
> + cdns,read-delay = <0>;
> + };
> +};
> +
> +&sdhci0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mmc0_pins_default>;
> + ti,driver-strength-ohm = <50>;
> + disable-wp;
> + non-removable;
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
> new file mode 100644
> index 000000000000..bad26b554f98
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
> @@ -0,0 +1,267 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2022 - 2023 PHYTEC Messtechnik GmbH
> + * Author: Wadim Egorov <w.egorov at phytec.de>
> + *
> + * Product homepage:
> + * https://www.phytec.com/product/phyboard-am62x
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include "k3-am625.dtsi"
> +#include "k3-am62-phycore-som.dtsi"
> +
> +/ {
> + compatible = "phytec,am625-phyboard-lyra-rdk",
> + "phytec,am62-phycore-som", "ti,am625";
> + model = "PHYTEC phyBOARD-Lyra AM625";
> +
> + aliases {
> + serial2 = &main_uart0;
> + serial3 = &main_uart1;
> + mmc1 = &sdhci1;
> + usb0 = &usb0;
> + usb1 = &usb1;
> + ethernet1 = &cpsw_port2;
> + };
> +
> + can_tc1: can-phy0 {
> + compatible = "ti,tcan1042";
> + #phy-cells = <0>;
> + max-bitrate = <5000000>;
> + standby-gpios = <&gpio_exp 1 GPIO_ACTIVE_HIGH>;
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> + autorepeat;
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio_keys_pins_default>;
> +
> + key-home {
> + label = "home";
> + linux,code = <KEY_HOME>;
> + gpios = <&main_gpio1 23 GPIO_ACTIVE_HIGH>;
> + };
> +
> + key-menu {
> + label = "menu";
> + linux,code = <KEY_MENU>;
> + gpios = <&gpio_exp 4 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&leds_pins_default &user_leds_pins_default>;
> +
> + led-1 {
> + gpios = <&main_gpio0 32 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "mmc0";
> + };
> +
> + led-2 {
> + gpios = <&gpio_exp 2 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "mmc1";
> + };
> + };
> +
> + vcc_3v3_mmc: regulator-vcc-3v3-mmc {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3_MMC";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +&main_pmx0 {
> + gpio_keys_pins_default: gpio-keys-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x1d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
> + >;
> + };
> +
> + gpio_exp_int_pins_default: gpio-exp-int-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x244, PIN_INPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
> + >;
> + };
> +
> + main_i2c1_pins_default: main-i2c1-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
> + AM62X_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
> + >;
> + };
> +
> + main_mcan0_pins_default: main-mcan0-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x1dc, PIN_INPUT, 0) /* (E15) MCAN0_RX */
> + AM62X_IOPAD(0x1d8, PIN_OUTPUT, 0) /* (C15) MCAN0_TX */
> + >;
> + };
> +
> + main_mmc1_pins_default: main-mmc1-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x23c, PIN_INPUT_PULLUP, 0) /* (A21) MMC1_CMD */
> + AM62X_IOPAD(0x234, PIN_INPUT_PULLDOWN, 0) /* (B22) MMC1_CLK */
> + AM62X_IOPAD(0x230, PIN_INPUT_PULLUP, 0) /* (A22) MMC1_DAT0 */
> + AM62X_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (B21) MMC1_DAT1 */
> + AM62X_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (C21) MMC1_DAT2 */
> + AM62X_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (D22) MMC1_DAT3 */
> + AM62X_IOPAD(0x240, PIN_INPUT_PULLUP, 0) /* (D17) MMC1_SDCD */
> + >;
> + };
> +
> + main_rgmii2_pins_default: main-rgmii2-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
> + AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
> + AM62X_IOPAD(0x18c, PIN_INPUT, 0) /* (AC21) RGMII2_RD2 */
> + AM62X_IOPAD(0x190, PIN_INPUT, 0) /* (AE22) RGMII2_RD3 */
> + AM62X_IOPAD(0x180, PIN_INPUT, 0) /* (AD23) RGMII2_RXC */
> + AM62X_IOPAD(0x17c, PIN_INPUT, 0) /* (AD22) RGMII2_RX_CTL */
> + AM62X_IOPAD(0x16c, PIN_OUTPUT, 0) /* (Y18) RGMII2_TD0 */
> + AM62X_IOPAD(0x170, PIN_OUTPUT, 0) /* (AA18) RGMII2_TD1 */
> + AM62X_IOPAD(0x174, PIN_OUTPUT, 0) /* (AD21) RGMII2_TD2 */
> + AM62X_IOPAD(0x178, PIN_OUTPUT, 0) /* (AC20) RGMII2_TD3 */
> + AM62X_IOPAD(0x168, PIN_OUTPUT, 0) /* (AE21) RGMII2_TXC */
> + AM62X_IOPAD(0x164, PIN_OUTPUT, 0) /* (AA19) RGMII2_TX_CTL */
> + >;
> + };
> +
> + main_uart0_pins_default: main-uart0-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
> + AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
> + >;
> + };
> +
> + main_uart1_pins_default: main-uart1-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x194, PIN_INPUT, 2) /* (B19) MCASP0_AXR3.UART1_CTSn */
> + AM62X_IOPAD(0x198, PIN_OUTPUT, 2) /* (A19) MCASP0_AXR2.UART1_RTSn */
> + AM62X_IOPAD(0x1ac, PIN_INPUT, 2) /* (E19) MCASP0_AFSR.UART1_RXD */
> + AM62X_IOPAD(0x1b0, PIN_OUTPUT, 2) /* (A20) MCASP0_ACLKR.UART1_TXD */
> + >;
> + };
> +
> + main_usb1_pins_default: main-usb1-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
> + >;
> + };
> +
> + user_leds_pins_default: user-leds-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x084, PIN_OUTPUT, 7) /* (L23) GPMC0_ADVn_ALE.GPIO0_32 */
> + >;
> + };
> +};
> +
> +&cpsw3g {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_rgmii1_pins_default
> + &main_rgmii2_pins_default>;
> +};
> +
> +&cpsw_port2 {
> + phy-mode = "rgmii-rxid";
> + phy-handle = <&cpsw3g_phy3>;
> +};
> +
> +&cpsw3g_mdio {
> + cpsw3g_phy3: ethernet-phy at 3 {
> + compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22";
> + reg = <3>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + };
> +};
> +
> +&main_i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c1_pins_default>;
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + gpio_exp: gpio-expander at 21 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio_exp_int_pins_default>;
> + compatible = "nxp,pcf8574";
> + reg = <0x21>;
> + interrupt-parent = <&main_gpio1>;
> + interrupts = <49 0>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + gpio-line-names = "GPIO0_HDMI_RST", "GPIO1_CAN0_nEN",
> + "GPIO2_LED2", "GPIO3_LVDS_GPIO",
> + "GPIO4_BUT2", "GPIO5_LVDS_BKLT_EN",
> + "GPIO6_ETH1_USER_RESET", "GPIO7_AUDIO_USER_RESET";
> + };
> +
> + eeprom at 51 {
> + compatible = "atmel,24c02";
> + pagesize = <16>;
> + reg = <0x51>;
> + };
> +};
> +
> +&main_mcan0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mcan0_pins_default>;
> + phys = <&can_tc1>;
> + status = "okay";
> +};
> +
> +&main_uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_uart0_pins_default>;
> + status = "okay";
> +};
> +
> +&main_uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_uart1_pins_default>;
> + /* Main UART1 may be used by TIFS firmware */
> + status = "okay";
> +};
> +
> +&sdhci1 {
> + vmmc-supply = <&vcc_3v3_mmc>;
> + vqmmc-supply = <&vddshv5_sdio>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mmc1_pins_default>;
> + ti,driver-strength-ohm = <50>;
> + disable-wp;
> + no-1-8-v;
> + status = "okay";
> +};
> +
> +&usbss0 {
> + ti,vbus-divider;
> + status = "okay";
> +};
> +
> +&usbss1 {
> + ti,vbus-divider;
> + status = "okay";
> +};
> +
> +&usb0 {
> + dr_mode = "peripheral";
> +};
> +
> +&usb1 {
> + dr_mode = "host";
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_usb1_pins_default>;
> +};
> --
> 2.25.1
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
More information about the linux-arm-kernel
mailing list