[PATCH v2 1/4] dt-bindings: usb: gpio-sbu-mux: add support for ss-data lanes mux

[Marco Felsch]

This adds the support for GPIO based USB-C SS data lane muxing.

Signed-off-by: Marco Felsch <m.felsch at pengutronix.de>
---
 .../devicetree/bindings/usb/gpio-sbu-mux.yaml      | 82 +++++++++++++++++++---
 1 file changed, 71 insertions(+), 11 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml b/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml
index bf4b1d016e1f..796f3283ac02 100644
--- a/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml
+++ b/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml
@@ -4,24 +4,26 @@
 $id: "http://devicetree.org/schemas/usb/gpio-sbu-mux.yaml#"
 $schema: "http://devicetree.org/meta-schemas/core.yaml#"
 
-title: GPIO-based SBU mux
+title: GPIO-based SS/SBU mux
 
 maintainers:
   - Bjorn Andersson <andersson at kernel.org>
 
 description:
-  In USB Type-C applications the SBU lines needs to be connected, disconnected
-  and swapped depending on the altmode and orientation. This binding describes
-  a family of hardware solutions which switches between these modes using GPIO
-  signals.
+  In USB Type-C applications the SS/SBU lines needs to be connected,
+  disconnected and swapped depending on the altmode and orientation. This
+  binding describes a family of hardware solutions which switches between these
+  modes using GPIO signals.
 
 properties:
   compatible:
-    items:
-      - enum:
-          - onnn,fsusb43l10x
-          - pericom,pi3usb102
-      - const: gpio-sbu-mux
+    oneOf:
+      - items:
+          - enum:
+              - onnn,fsusb43l10x
+              - pericom,pi3usb102
+          - const: gpio-sbu-mux
+      - const: gpio-ss-mux
 
   enable-gpios:
     description: Switch enable GPIO
@@ -50,10 +52,18 @@ required:
   - compatible
   - enable-gpios
   - select-gpios
-  - mode-switch
   - orientation-switch
   - port
 
+if:
+  properties:
+    compatible:
+      contains:
+        const: gpio-sbu-mux
+then:
+  required:
+    - mode-switch
+
 additionalProperties: false
 
 examples:
@@ -107,4 +117,54 @@ examples:
             };
         };
     };
+
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    tcpm {
+        connector {
+            compatible = "usb-c-connector";
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port at 0 {
+                    reg = <0>;
+                    tcpm_hs_out: endpoint {
+                        remote-endpoint = <&usb_hs_phy_in>;
+                    };
+                };
+
+                port at 1 {
+                    reg = <1>;
+                    tcpm_ss_out: endpoint {
+                        remote-endpoint = <&usb_ss_phy_in>;
+                    };
+                };
+
+                port at 2 {
+                    reg = <2>;
+                    tcpm_ss_mux_out: endpoint {
+                        remote-endpoint = <&ss_mux_in>;
+                    };
+                };
+            };
+        };
+    };
+
+    usb-ss-mux {
+        compatible = "gpio-ss-mux";
+
+        enable-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
+        select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>;
+
+        orientation-switch;
+
+        port {
+            ss_mux_in: endpoint {
+                remote-endpoint = <&tcpm_ss_mux_out>;
+            };
+        };
+    };
 ...

-- 
2.39.2