[PATCH v4 3/5] PCI: brcmstb: Set PCIe transaction completion timeout

[Stefan Wahren]

Hi Jim,

Am 29.04.23 um 00:34 schrieb Jim Quinlan:
> Since the STB PCIe HW will cause a CPU abort on a PCIe transaction
> completion timeout abort, we might as well extend the default timeout
> limit.  Further, different devices and systems may requires a larger or
> smaller amount commensurate with their L1SS exit time, so the property
> "brcm,completion-timeout-us" may be used to set a custom timeout value.
> 
> Tested-by: Florian Fainelli <f.fainelli at gmail.com>
> Signed-off-by: Jim Quinlan <jim2101024 at gmail.com>
> ---
>   drivers/pci/controller/pcie-brcmstb.c | 30 +++++++++++++++++++++++++++
>   1 file changed, 30 insertions(+)
> 
> diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
> index c4b076ea5180..c2cb683447ac 100644
> --- a/drivers/pci/controller/pcie-brcmstb.c
> +++ b/drivers/pci/controller/pcie-brcmstb.c
> @@ -1080,6 +1080,35 @@ static void brcm_config_clkreq(struct brcm_pcie *pcie)
>   	writel(clkreq_set, pcie->base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
>   }
>   
> +static void brcm_config_completion_timeout(struct brcm_pcie *pcie)
> +{
> +	/* TIMEOUT register is two registers before RGR1_SW_INIT_1 */
> +	const char *fmt = "brcm,completion-timeout-us clamped to region [%u..%u]\n";
> +	const unsigned int REG_OFFSET = PCIE_RGR1_SW_INIT_1(pcie) - 8;
> +	const u32 timeout_us_min = 16;
> +	const u32 timeout_us_max = 19884107;
> +	u32 timeout_us = 1000000; /* Our default, 1 second */
> +	int rval, ret;
> +
> +	ret = of_property_read_u32(pcie->np, "brcm,completion-timeout-us",
> +				   &timeout_us);
> +	if (ret && ret != -EINVAL)
> +		dev_err(pcie->dev, "malformed/invalid 'brcm,completion-timeout-us'\n");
> +
> +	/* If needed, clamp the requested timeout value and issue a warning */
> +	if (timeout_us < timeout_us_min) {
> +		timeout_us = timeout_us_min;
> +		dev_warn(pcie->dev, fmt, timeout_us_min, timeout_us_max);
> +	} else if (timeout_us > timeout_us_max) {
> +		timeout_us = timeout_us_max;
> +		dev_warn(pcie->dev, fmt, timeout_us_min, timeout_us_max);
> +	}
> +
> +	/* Each unit in timeout register is 1/216,000,000 seconds */
> +	rval = 216 * timeout_us;
> +	writel(rval, pcie->base + REG_OFFSET);

i don't think "int" is the proper type for rval here

> +}
> +
>   static int brcm_pcie_start_link(struct brcm_pcie *pcie)
>   {
>   	struct device *dev = pcie->dev;
> @@ -1110,6 +1139,7 @@ static int brcm_pcie_start_link(struct brcm_pcie *pcie)
>   		return -ENODEV;
>   	}
>   
> +	brcm_config_completion_timeout(pcie);
>   	brcm_config_clkreq(pcie);
>   
>   	if (pcie->gen)