[PATCH] arm64: dts: imx8mp: add vpu pgc nodes

[Peng Fan]

> Subject: Re: [PATCH] arm64: dts: imx8mp: add vpu pgc nodes
> 
> On 22/8/22 14:45, Peng Fan wrote:
> > Add i.MX8MP PGC nodes for vpu, which are used to supply power for VPU.
> >
> > Signed-off-by: Peng Fan <peng.fan at nxp.com>
> > Signed-off-by: Shawn Guo <shawnguo at kernel.org>
> > ---
> >  arch/arm64/boot/dts/freescale/imx8mp.dtsi | 27
> > +++++++++++++++++++++++
> >  1 file changed, 27 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> > b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> > index 0b165f98a82c..34af983b0210 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> > @@ -598,6 +598,33 @@ pgc_ispdwp: power-domain at 18 {
> >                                                 reg =
> <IMX8MP_POWER_DOMAIN_MEDIAMIX_ISPDWP>;
> >                                                 clocks = <&clk IMX8MP_CLK_MEDIA_ISP_ROOT>;
> >                                         };
> > +
> > +                                       pgc_vpumix: power-domain at 19 {
> > +                                               #power-domain-cells = <0>;
> > +                                               reg = <IMX8MP_POWER_DOMAIN_VPUMIX>;
> > +                                               clocks =<&clk IMX8MP_CLK_VPU_ROOT>;
> > +                                       };
> > +
> > +                                       pgc_vpu_g1: power-domain at 20 {
> > +                                               #power-domain-cells = <0>;
> > +                                               power-domains = <&pgc_vpumix>;
> > +                                               reg = <IMX8MP_POWER_DOMAIN_VPU_G1>;
> > +                                               clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>;
> > +                                       };
> > +
> > +                                       pgc_vpu_g2: power-domain at 21 {
> > +                                               #power-domain-cells = <0>;
> > +                                               power-domains = <&pgc_vpumix>;
> > +                                               reg = <IMX8MP_POWER_DOMAIN_VPU_G2>;
> > +                                               clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>;
> > +                                       };
> > +
> > +                                       pgc_vpu_vc8000e: power-domain at 22 {
> > +                                               #power-domain-cells = <0>;
> > +                                               power-domains = <&pgc_vpumix>;
> > +                                               reg =
> <IMX8MP_POWER_DOMAIN_VPU_VC8000E>;
> > +                                               clocks = <&clk
> IMX8MP_CLK_VPU_VC8KE_ROOT>;
> > +                                       };
> >                                 };
> >                         };
> >                 };
> 
> This change causes new error messages to come out during boot, for
> example:
> 
>     ...
>     imx-pgc imx-pgc-domain.8: failed to command PGC
>     imx-pgc imx-pgc-domain.8: failed to command PGC
>     imx-pgc imx-pgc-domain.8: failed to command PGC
>     30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 197, base_baud =
> 1500000) is a IMX
>     ...
>     hwmon hwmon1: temp1_input not attached to any thermal zone
>     imx-pgc imx-pgc-domain.8: failed to command PGC
>     imx-pgc imx-pgc-domain.8: failed to command PGC
>     imx-pgc imx-pgc-domain.8: failed to command PGC
>     ...
> 
> They don't seem to cause any problems on the hardware I am using, well, at
> least not that I have found so far.
> 
> This first appeared for me in linux-6.1. But it is the same in todays linux 6.3-
> rc4. Reverting this change (not completely trivial due to a couple of commits
> after it that rely on it) fixes it - no more errors.
[Peng Fan] 

The VPU BLK CTRL seems not enabled.

Regards,
Peng.

> 
> Regards
> Greg
>