[PATCH v2 4/4] ARM: dts: sunxi: add MangoPi MQ-R-T113 board
Andre Przywara
andre.przywara at arm.com
Mon Mar 27 02:21:18 PDT 2023
On Mon, 27 Mar 2023 10:30:33 +0200
Belisko Marek <marek.belisko at gmail.com> wrote:
Hi Marek,
thanks for testing!
> On Mon, Mar 20, 2023 at 1:53 AM Andre Przywara <andre.przywara at arm.com> wrote:
> >
> > The MangoPi MQ-R-T113 is a small SBC with the Allwinner T113-s3 SoC.
> > The SoC features two Arm Cortex-A7 cores and 128 MB of co-packaged DDR3
> > DRAM. The board adds mostly connectors and the required regulators, plus
> > a Realtek RTL8189FTV WiFi chip.
> > Power comes in via a USB-C connector wired as a peripheral, and there is
> > a second USB-C connector usable as a host port.
> >
> > Add a .dtsi file describing most of the board's peripherals, and include
> > that from the actual board .dts file. This allows to re-use the .dtsi
> > for the MQ-R-F113 RISC-V variant of that board.
> >
> > Signed-off-by: Andre Przywara <andre.przywara at arm.com>
> > ---
> > arch/arm/boot/dts/Makefile | 1 +
> > .../dts/sun8i-t113s-mangopi-mq-r-t113.dts | 35 +++++
> > .../boot/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi | 126 ++++++++++++++++++
> > 3 files changed, 162 insertions(+)
> > create mode 100644 arch/arm/boot/dts/sun8i-t113s-mangopi-mq-r-t113.dts
> > create mode 100644 arch/arm/boot/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index efe4152e5846d..3367e24146da8 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -1397,6 +1397,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> > sun8i-s3-elimo-initium.dtb \
> > sun8i-s3-lichee-zero-plus.dtb \
> > sun8i-s3-pinecube.dtb \
> > + sun8i-t113s-mangopi-mq-r-t113.dtb \
> > sun8i-t3-cqa3t-bv3.dtb \
> > sun8i-v3-sl631-imx179.dtb \
> > sun8i-v3s-licheepi-zero.dtb \
> > diff --git a/arch/arm/boot/dts/sun8i-t113s-mangopi-mq-r-t113.dts b/arch/arm/boot/dts/sun8i-t113s-mangopi-mq-r-t113.dts
> > new file mode 100644
> > index 0000000000000..94e24b5926dd7
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/sun8i-t113s-mangopi-mq-r-t113.dts
> > @@ -0,0 +1,35 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> > +// Copyright (C) 2022 Arm Ltd.
> > +
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +
> > +/dts-v1/;
> > +
> > +#include "sun8i-t113s.dtsi"
> > +#include "sunxi-d1s-t113-mangopi-mq-r.dtsi"
> > +
> > +/ {
> > + model = "MangoPi MQ-R-T113";
> > + compatible = "widora,mangopi-mq-r-t113", "allwinner,sun8i-t113s";
> > +
> > + aliases {
> > + ethernet0 = &rtl8189ftv;
> > + };
> > +};
> > +
> > +&cpu0 {
> > + cpu-supply = <®_vcc_core>;
> > +};
> > +
> > +&cpu1 {
> > + cpu-supply = <®_vcc_core>;
> > +};
> Tested on MQ-R-T113 Mangopi on top of 6.3-rc3 and on booted system I
> have only one CPU available:
Right, thanks for the heads up. The reason is that the current U-Boot
branch does not enable PSCI services, so the kernel does not know how to
enable and online the second core. As with the other 32-bit parts, the
PSCI nodes and properties get inserted into the DT by U-Boot, at runtime:
arch/arm/lib/psci-dt.c:fdt_psci().
It should be fairly straight-forward to enable that in U-Boot, I will try
to look into this later this week.
Cheers,
Andre
> root at t113:~# cat /proc/cpuinfo
> processor : 0
> model name : ARMv7 Processor rev 5 (v7l)
> BogoMIPS : 48.00
> Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4
> idiva idivt vfpd32 lpae evtstrm
> CPU implementer : 0x41
> CPU architecture: 7
> CPU variant : 0x0
> CPU part : 0xc07
> CPU revision : 5
>
> Hardware : Generic DT based system
> Revision : 0000
> Serial : 9340600081169098
>
> bootlog shows:
> [ 0.003515] /cpus/cpu at 0 missing clock-frequency property
> [ 0.003601] /cpus/cpu at 1 missing clock-frequency property
> [ 0.003640] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
>
> > +
> > +&mmc1 {
> > + rtl8189ftv: wifi at 1 {
> > + reg = <1>;
> > + interrupt-parent = <&pio>;
> > + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 = WL_WAKE_AP */
> > + interrupt-names = "host-wake";
> > + };
> > +};
> > diff --git a/arch/arm/boot/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi b/arch/arm/boot/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
> > new file mode 100644
> > index 0000000000000..e9bc749488bb2
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
> > @@ -0,0 +1,126 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> > +// Copyright (C) 2022 Arm Ltd.
> > +/*
> > + * Common peripherals and configurations for MangoPi MQ-R boards.
> > + */
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/leds/common.h>
> > +
> > +/ {
> > + aliases {
> > + serial3 = &uart3;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial3:115200n8";
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + led-0 {
> > + color = <LED_COLOR_ID_BLUE>;
> > + function = LED_FUNCTION_STATUS;
> > + gpios = <&pio 3 22 GPIO_ACTIVE_LOW>; /* PD22 */
> > + };
> > + };
> > +
> > + /* board wide 5V supply directly from the USB-C socket */
> > + reg_vcc5v: regulator-5v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc-5v";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + };
> > +
> > + /* SY8008 DC/DC regulator on the board */
> > + reg_3v3: regulator-3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc-3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + vin-supply = <®_vcc5v>;
> > + };
> > +
> > + /* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
> > + reg_vcc_core: regulator-core {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc-core";
> > + regulator-min-microvolt = <880000>;
> > + regulator-max-microvolt = <880000>;
> > + vin-supply = <®_vcc5v>;
> > + };
> > +
> > + /* XC6206 LDO on the board */
> > + reg_avdd2v8: regulator-avdd {
> > + compatible = "regulator-fixed";
> > + regulator-name = "avdd2v8";
> > + regulator-min-microvolt = <2800000>;
> > + regulator-max-microvolt = <2800000>;
> > + vin-supply = <®_3v3>;
> > + };
> > +
> > + wifi_pwrseq: wifi-pwrseq {
> > + compatible = "mmc-pwrseq-simple";
> > + reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
> > + };
> > +};
> > +
> > +&dcxo {
> > + clock-frequency = <24000000>;
> > +};
> > +
> > +&ehci1 {
> > + status = "okay";
> > +};
> > +
> > +&mmc0 {
> > + pinctrl-0 = <&mmc0_pins>;
> > + pinctrl-names = "default";
> > + vmmc-supply = <®_3v3>;
> > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> > + disable-wp;
> > + bus-width = <4>;
> > + status = "okay";
> > +};
> > +
> > +&mmc1 {
> > + pinctrl-0 = <&mmc1_pins>;
> > + pinctrl-names = "default";
> > + vmmc-supply = <®_3v3>;
> > + non-removable;
> > + bus-width = <4>;
> > + mmc-pwrseq = <&wifi_pwrseq>;
> > + status = "okay";
> > +};
> > +
> > +&ohci1 {
> > + status = "okay";
> > +};
> > +
> > +&pio {
> > + vcc-pb-supply = <®_3v3>;
> > + vcc-pd-supply = <®_3v3>;
> > + vcc-pe-supply = <®_avdd2v8>;
> > + vcc-pf-supply = <®_3v3>;
> > + vcc-pg-supply = <®_3v3>;
> > +};
> > +
> > +&uart3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart3_pb_pins>;
> > + status = "okay";
> > +};
> > +
> > +/* The USB-C socket has its CC pins pulled to GND, so is hardwired as a UFP. */
> > +&usb_otg {
> > + dr_mode = "peripheral";
> > + status = "okay";
> > +};
> > +
> > +&usbphy {
> > + usb1_vbus-supply = <®_vcc5v>;
> > + status = "okay";
> > +};
> > --
> > 2.35.7
> >
>
> BR,
>
> marek
>
More information about the linux-arm-kernel
mailing list