[PATCH] arm64: dts: ti: k3-j784s4-evm: Add OSPI0 flash support

[Krzysztof Kozlowski]

On 27/03/2023 10:29, Apurva Nandan wrote:
> Add support for OSPI flash connected to OSPI0 instance through FSS.
> Also enumerate OSPI1 instance in MCU DTSI.



> +
> +&ospi0 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> +
> +	flash at 0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0x0>;
> +		spi-tx-bus-width = <8>;
> +		spi-rx-bus-width = <8>;
> +		spi-max-frequency = <25000000>;
> +		cdns,tshsl-ns = <60>;
> +		cdns,tsd2d-ns = <60>;
> +		cdns,tchsh-ns = <60>;
> +		cdns,tslch-ns = <60>;
> +		cdns,read-delay = <4>;
> +		cdns,phy-mode;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +	};
> +};
> +
>  &main_i2c0 {
>  	status = "okay";
>  	pinctrl-names = "default";
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> index 93952af618f6..b29b95a532f6 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> @@ -308,4 +308,47 @@ cpts at 3d000 {
>  			ti,cpts-periodic-outputs = <2>;
>  		};
>  	};
> +
> +	fss: syscon at 47000000 {
> +		compatible = "syscon", "simple-mfd";

NAK. This is not allowed on itself and dtbs_check would warn you.

> +		reg = <0x00 0x47000000 0x00 0x100>;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +		status = "disabled";
> +
> +		ospi0: spi at 47040000 {
> +			compatible = "ti,am654-ospi", "cdns,qspi-nor";
> +			reg = <0x00 0x47040000 0x00 0x100>,
> +			      <0x5 0x0000000 0x1 0x0000000>;
> +			interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
> +			cdns,fifo-depth = <256>;
> +			cdns,fifo-width = <4>;
> +			cdns,trigger-address = <0x0>;
> +			clocks = <&k3_clks 161 7>;
> +			assigned-clocks = <&k3_clks 161 7>;
> +			assigned-clock-parents = <&k3_clks 161 9>;
> +			assigned-clock-rates = <166666666>;
> +			power-domains = <&k3_pds 161 TI_SCI_PD_EXCLUSIVE>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		ospi1: spi at 47050000 {
> +			compatible = "ti,am654-ospi", "cdns,qspi-nor";
> +			reg = <0x00 0x47050000 0x00 0x100>,
> +			      <0x7 0x0000000 0x1 0x0000000>;
> +			interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
> +			cdns,fifo-depth = <256>;
> +			cdns,fifo-width = <4>;
> +			cdns,trigger-address = <0x0>;
> +			clocks = <&k3_clks 162 7>;
> +			power-domains = <&k3_pds 162 TI_SCI_PD_EXCLUSIVE>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +	};
> +

Don't add stay blank lines.

>  };

Best regards,
Krzysztof