[PATCH V3 7/7] arm64: dts: imx8mp: add interconnect for hsio blk ctrl

[Greg Ungerer]

Hi Alexander,

On 27/3/23 16:27, Alexander Stein wrote:
> Hi Greg,
> 
> Am Montag, 27. März 2023, 06:50:37 CEST schrieb Greg Ungerer:
>> On 2/3/22 17:13, Peng Fan wrote:
>>> From: Peng Fan <peng.fan at nxp.com>
>>>
>>> Add interconnect property for hsio blk ctrl
>>>
>>> Signed-off-by: Peng Fan <peng.fan at nxp.com>
>>> ---
>>>
>>   > arch/arm64/boot/dts/freescale/imx8mp.dtsi | 5 +++++
>>   > 1 file changed, 5 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
>>> b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index
>>> 08bd57742294..9cceeeeb26be 100644
>>> --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
>>> @@ -1109,6 +1109,11 @@ hsio_blk_ctrl: blk-ctrl at 32f10000 {
>>>
>>>   						<&pgc_hsiomix>,
> <&pgc_pcie_phy>;
>>>   				
>>>   				power-domain-names = "bus", "usb",
> "usb-phy1",
>>>   				
>>>   						     "usb-phy2",
> "pcie", "pcie-phy";
>>>
>>> +				interconnects = <&noc
> IMX8MP_ICM_NOC_PCIE &noc IMX8MP_ICN_HSIO>,
>>> +						<&noc
> IMX8MP_ICM_USB1 &noc IMX8MP_ICN_HSIO>,
>>> +						<&noc
> IMX8MP_ICM_USB2 &noc IMX8MP_ICN_HSIO>,
>>> +						<&noc
> IMX8MP_ICM_PCIE &noc IMX8MP_ICN_HSIO>;
>>> +				interconnect-names = "noc-pcie",
> "usb1", "usb2", "pcie";
>>>
>>>   				#power-domain-cells = <1>;
>>>   			
>>>   			};
>>>   		
>>>   		};
>>
>> This change completely breaks USB for me on a new iMX8mp platform I am
>> working with. Before this change normal USB probe looks good:
>>
>>      xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
>>      xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
>>      xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe6d hci version 0x110 quirks
>> 0x0000000000010010 xhci-hcd xhci-hcd.0.auto: irq 206, io mem 0x38100000
>>      xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
>>      xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
>>      xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
>>      usb usb1: New USB device found, idVendor=1d6b, idProduct=0002,
>> bcdDevice= 6.03 usb usb1: New USB device strings: Mfr=3, Product=2,
>> SerialNumber=1 usb usb1: Product: xHCI Host Controller
>>      usb usb1: Manufacturer: Linux 6.3.0-rc4-dirty xhci-hcd
>>      ....
>>
>> But after this commit is applied, no USB probe messages at all.
>>
>> USB worked fine in 6.0 for me, but when I switched up to 6.1 USB was broken,
>> I bisected to this as being the offending commit. This is still broken for
>> me in todays 6.3-rc4. If I revert this change (and only this change) USB
>> works again.
>>
>> Any thoughts on why this breaks USB?
> 
> Maybe you are missing CONFIG_INTERCONNECT_IMX8MP?

No, it is enabled. From my config:

     CONFIG_INTERCONNECT=y
     CONFIG_INTERCONNECT_IMX=y
     # CONFIG_INTERCONNECT_IMX8MM is not set
     # CONFIG_INTERCONNECT_IMX8MN is not set
     # CONFIG_INTERCONNECT_IMX8MQ is not set
     CONFIG_INTERCONNECT_IMX8MP=y

Regards
Greg