[PATCH v8 3/5] ARM: dts: stm32: add CAN support on stm32f429

[Dario Binacchi]

Add support for bxcan (Basic eXtended CAN controller) to STM32F429. The
chip contains two CAN peripherals, CAN1 the master and CAN2 the slave,
that share some of the required logic like clock and filters. This means
that the slave CAN can't be used without the master CAN.

Signed-off-by: Dario Binacchi <dario.binacchi at amarulasolutions.com>

---

(no changes since v6)

Changes in v6:
- move can1 node before gcan to keep ordering by address.

Changes in v4:
- Replace the node can at 40006400 (compatible "st,stm32f4-bxcan-core")
  with the gcan at 40006600 node ("sysnode" compatible). The gcan node
  contains clocks and memory addresses shared by the two can nodes
  of which it's no longer the parent.
- Add to can nodes the "st,gcan" property (global can memory) which
  references the gcan at 40006600 node ("sysnode compatibble).

Changes in v3:
- Remove 'Dario Binacchi <dariobin at libero.it>' SOB.
- Add "clocks" to can at 0 node.

 arch/arm/boot/dts/stm32f429.dtsi | 29 +++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)

diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
index c31ceb821231..809b2842ded9 100644
--- a/arch/arm/boot/dts/stm32f429.dtsi
+++ b/arch/arm/boot/dts/stm32f429.dtsi
@@ -362,6 +362,35 @@ i2c3: i2c at 40005c00 {
 			status = "disabled";
 		};
 
+		can1: can at 40006400 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40006400 0x200>;
+			interrupts = <19>, <20>, <21>, <22>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F4_APB1_RESET(CAN1)>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(CAN1)>;
+			st,can-master;
+			st,gcan = <&gcan>;
+			status = "disabled";
+		};
+
+		gcan: gcan at 40006600 {
+			compatible = "st,stm32f4-gcan", "syscon";
+			reg = <0x40006600 0x200>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(CAN1)>;
+		};
+
+		can2: can at 40006800 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40006800 0x200>;
+			interrupts = <63>, <64>, <65>, <66>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F4_APB1_RESET(CAN2)>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(CAN2)>;
+			st,gcan = <&gcan>;
+			status = "disabled";
+		};
+
 		dac: dac at 40007400 {
 			compatible = "st,stm32f4-dac-core";
 			reg = <0x40007400 0x400>;
-- 
2.32.0