[PATCH 4/5] arm64: dts: rockchip: fix gmac support for NanoPi R5S

[Tianling Shen]

Hi Jonas,

On Thu, Mar 16, 2023 at 3:37 PM Jonas Karlman <jonas at kwiboo.se> wrote:
>
> Hi Tianling,
> On 2023-03-16 06:34, Tianling Shen wrote:
> > Hi Vasily,
> >
> > On Thu, Mar 16, 2023 at 8:16 AM Vasily Khoruzhick <anarsoul at gmail.com> wrote:
> >>
> >> On Wed, Mar 15, 2023 at 9:02 AM Tianling Shen <cnsztl at gmail.com> wrote:
> >>>
> >>> - Changed phy-mode to rgmii.
> >>>
> >>> - Fixed pull type in pinctrl for gmac0.
> >>>
> >>> - Removed duplicate properties in mdio node.
> >>>   These properties are defined in the gmac0 node already.
> >>>
> >>> Signed-off-by: Tianling Shen <cnsztl at gmail.com>
> >>> ---
> >>>  arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts | 7 ++-----
> >>>  1 file changed, 2 insertions(+), 5 deletions(-)
> >>>
> >>> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts
> >>> index e9adf5e66529..2a1118f15c29 100644
> >>> --- a/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts
> >>> +++ b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts
> >>> @@ -57,7 +57,7 @@
> >>>         assigned-clock-rates = <0>, <125000000>;
> >>>         clock_in_out = "output";
> >>>         phy-handle = <&rgmii_phy0>;
> >>> -       phy-mode = "rgmii-id";
> >>> +       phy-mode = "rgmii";
> >>>         pinctrl-names = "default";
> >>>         pinctrl-0 = <&gmac0_miim
> >>>                      &gmac0_tx_bus2
> >>> @@ -79,9 +79,6 @@
> >>>                 reg = <1>;
> >>>                 pinctrl-0 = <&eth_phy0_reset_pin>;
> >>>                 pinctrl-names = "default";
> >>> -               reset-assert-us = <10000>;
> >>> -               reset-deassert-us = <50000>;
> >>> -               reset-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_LOW>;
> >>
> >> Hmm, I don't see RK_PC4 being used anywhere else. gmac0 has RK_PC5 as
> >
> > Yes, it's a typo, it should be RK_RC5.
> >
> >> snsp,reset-gpio. So it essentially drops reset for the PHY. Is it
> >> expected?
> >
> > snsp,reset-gpio defined reset already, so we don't need to set it here again.
> >
> > ---
> >
> > snsp,reset-gpio is the legacy binding, but I still have no idea why
> > reset-gpios doesn't work,
> > the dwmac driver will fail to lookup phy:
> >
> > [   10.398514] rk_gmac-dwmac fe2a0000.ethernet eth0: no phy found
> > [   10.399061] rk_gmac-dwmac fe2a0000.ethernet eth0: __stmmac_open:
> > Cannot attach to PHY (error: -19)
> >
> > Any ideas would be appreciated.
>
> Generic ethernet phy driver is not resetting the phy in the same way
> that snsp,reset-gpio does, please see top two commits at [1].
>
> I have been meaning to send that out as an RFC but I got stuck in a
> u-boot rabbit hole, and I also do not know what the correct way to fix
> this would be, so I played with both device tree and code changes.
> Will prioritize this and send out a RFC later today.
>
> [1] https://github.com/Kwiboo/linux-rockchip/commits/rk3568-eth-phy-reset

Thanks for the hint! I will test your patches tonight.

Thanks,
Tianling.

>
> Regards,
> Jonas
>
> >
> > Thanks,
> > Tianling.
> >
> >>
> >>>         };
> >>>  };
> >>>
> >>> @@ -115,7 +112,7 @@
> >>>  &pinctrl {
> >>>         gmac0 {
> >>>                 eth_phy0_reset_pin: eth-phy0-reset-pin {
> >>> -                       rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;
> >>> +                       rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_up>;
> >>>                 };
> >>>         };
> >>>
> >>> --
> >>> 2.17.1
> >>>
>