[PATCH V2 2/3] arm64: dts: ti: Use local header for pinctrl register values

Nishanth Menon nm at ti.com
Wed Mar 15 08:52:27 PDT 2023 

The DTS uses hardware register values directly in pin controller pin
configuration and not an abstraction of any form.

These definitions were previously put in the bindings header to avoid
code duplication and to provide some context meaning (name), but they
do not fit the purpose of bindings.

Store the constants in a header next to DTS and use them instead of
bindings.

Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
Suggested-by: Linus Walleij <linus.walleij at linaro.org>
Link: https://lore.kernel.org/all/c4d53e9c-dac0-8ccc-dc86-faada324beba@linaro.org/
Signed-off-by: Nishanth Menon <nm at ti.com>
---

Changes since V1:
 - Updated $subject and $commit-message
 - Dropped the deletion of bindings header (instead followon patch
   provides a deprecation warning)
 - NOTE: checkpatch insists the following error exists:
   ERROR: Macros with complex values should be enclosed in parentheses
   However, as explained in patches to include/dt-bindings/pinctrl/k3.h,
   we do not need parentheses enclosing the values for this macro as we
   do intend it to generate two separate values as has been done for
   other similar platforms.

V1: https://lore.kernel.org/linux-arm-kernel/20230311131325.9750-3-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am62.dtsi   |  3 +-
 arch/arm64/boot/dts/ti/k3-am62a.dtsi  |  3 +-
 arch/arm64/boot/dts/ti/k3-am64.dtsi   |  3 +-
 arch/arm64/boot/dts/ti/k3-am65.dtsi   |  3 +-
 arch/arm64/boot/dts/ti/k3-j7200.dtsi  |  3 +-
 arch/arm64/boot/dts/ti/k3-j721e.dtsi  |  3 +-
 arch/arm64/boot/dts/ti/k3-j721s2.dtsi |  3 +-
 arch/arm64/boot/dts/ti/k3-j784s4.dtsi |  3 +-
 arch/arm64/boot/dts/ti/k3-pinctrl.h   | 53 +++++++++++++++++++++++++++
 9 files changed, 69 insertions(+), 8 deletions(-)
 create mode 100644 arch/arm64/boot/dts/ti/k3-pinctrl.h

diff --git a/arch/arm64/boot/dts/ti/k3-am62.dtsi b/arch/arm64/boot/dts/ti/k3-am62.dtsi
index 37fcbe7a3c33..a401f5225243 100644
--- a/arch/arm64/boot/dts/ti/k3-am62.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62.dtsi
@@ -8,9 +8,10 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
 #include <dt-bindings/soc/ti,sci_pm_domain.h>
 
+#include "k3-pinctrl.h"
+
 / {
 	model = "Texas Instruments K3 AM625 SoC";
 	compatible = "ti,am625";
diff --git a/arch/arm64/boot/dts/ti/k3-am62a.dtsi b/arch/arm64/boot/dts/ti/k3-am62a.dtsi
index 6eb87c3f9f3c..fe60c9ce21e3 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a.dtsi
@@ -8,9 +8,10 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
 #include <dt-bindings/soc/ti,sci_pm_domain.h>
 
+#include "k3-pinctrl.h"
+
 / {
 	model = "Texas Instruments K3 AM62A SoC";
 	compatible = "ti,am62a7";
diff --git a/arch/arm64/boot/dts/ti/k3-am64.dtsi b/arch/arm64/boot/dts/ti/k3-am64.dtsi
index c858725133af..60fe95b48312 100644
--- a/arch/arm64/boot/dts/ti/k3-am64.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64.dtsi
@@ -8,9 +8,10 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
 #include <dt-bindings/soc/ti,sci_pm_domain.h>
 
+#include "k3-pinctrl.h"
+
 / {
 	model = "Texas Instruments K3 AM642 SoC";
 	compatible = "ti,am642";
diff --git a/arch/arm64/boot/dts/ti/k3-am65.dtsi b/arch/arm64/boot/dts/ti/k3-am65.dtsi
index c538a0bf3cdd..3093ef6b9b23 100644
--- a/arch/arm64/boot/dts/ti/k3-am65.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65.dtsi
@@ -8,9 +8,10 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
 #include <dt-bindings/soc/ti,sci_pm_domain.h>
 
+#include "k3-pinctrl.h"
+
 / {
 	model = "Texas Instruments K3 AM654 SoC";
 	compatible = "ti,am654";
diff --git a/arch/arm64/boot/dts/ti/k3-j7200.dtsi b/arch/arm64/boot/dts/ti/k3-j7200.dtsi
index d74f86b0f622..bbe380c72a7e 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200.dtsi
@@ -7,9 +7,10 @@
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
 #include <dt-bindings/soc/ti,sci_pm_domain.h>
 
+#include "k3-pinctrl.h"
+
 / {
 	model = "Texas Instruments K3 J7200 SoC";
 	compatible = "ti,j7200";
diff --git a/arch/arm64/boot/dts/ti/k3-j721e.dtsi b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
index 6975cae644d9..4c7d5f9d61a8 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
@@ -7,9 +7,10 @@
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
 #include <dt-bindings/soc/ti,sci_pm_domain.h>
 
+#include "k3-pinctrl.h"
+
 / {
 	model = "Texas Instruments K3 J721E SoC";
 	compatible = "ti,j721e";
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2.dtsi
index 78295ee0fee5..376924726f1f 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2.dtsi
@@ -10,9 +10,10 @@
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
 #include <dt-bindings/soc/ti,sci_pm_domain.h>
 
+#include "k3-pinctrl.h"
+
 / {
 
 	model = "Texas Instruments K3 J721S2 SoC";
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
index 3eb0d0568959..2e03d84da7d2 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
@@ -10,9 +10,10 @@
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
 #include <dt-bindings/soc/ti,sci_pm_domain.h>
 
+#include "k3-pinctrl.h"
+
 / {
 	model = "Texas Instruments K3 J784S4 SoC";
 	compatible = "ti,j784s4";
diff --git a/arch/arm64/boot/dts/ti/k3-pinctrl.h b/arch/arm64/boot/dts/ti/k3-pinctrl.h
new file mode 100644
index 000000000000..c97548a3f42d
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-pinctrl.h
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides constants for pinctrl bindings for TI's K3 SoC
+ * family.
+ *
+ * Copyright (C) 2018-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+#ifndef DTS_ARM64_TI_K3_PINCTRL_H
+#define DTS_ARM64_TI_K3_PINCTRL_H
+
+#define PULLUDEN_SHIFT		(16)
+#define PULLTYPESEL_SHIFT	(17)
+#define RXACTIVE_SHIFT		(18)
+
+#define PULL_DISABLE		(1 << PULLUDEN_SHIFT)
+#define PULL_ENABLE		(0 << PULLUDEN_SHIFT)
+
+#define PULL_UP			(1 << PULLTYPESEL_SHIFT | PULL_ENABLE)
+#define PULL_DOWN		(0 << PULLTYPESEL_SHIFT | PULL_ENABLE)
+
+#define INPUT_EN		(1 << RXACTIVE_SHIFT)
+#define INPUT_DISABLE		(0 << RXACTIVE_SHIFT)
+
+/* Only these macros are expected be used directly in device tree files */
+#define PIN_OUTPUT		(INPUT_DISABLE | PULL_DISABLE)
+#define PIN_OUTPUT_PULLUP	(INPUT_DISABLE | PULL_UP)
+#define PIN_OUTPUT_PULLDOWN	(INPUT_DISABLE | PULL_DOWN)
+#define PIN_INPUT		(INPUT_EN | PULL_DISABLE)
+#define PIN_INPUT_PULLUP	(INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN	(INPUT_EN | PULL_DOWN)
+
+#define AM62AX_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM62AX_MCU_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define AM62X_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM62X_MCU_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define AM64X_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM64X_MCU_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define AM65X_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM65X_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define J721E_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define J721E_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define J721S2_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define J721S2_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define J784S4_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define J784S4_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#endif
-- 
2.40.0

More information about the linux-arm-kernel mailing list