[PATCH] arm64: dts: imx8mp-debix: add USB host support

[Shawn Guo]

On Tue, Feb 28, 2023 at 06:02:47PM +0100, Lucas Stach wrote:
> This adds support for the 4 USB3 host ports on the board, which are
> connected to the i.MX8MP SoC via a Realtek RTS5411 hub.
> 
> As the schematic for the board is not available, I could not validate
> that this really reflects the reality, but I modeled things after the
> hacked in usage of the GPIOs in the downstream kernel.
> 
> Signed-off-by: Lucas Stach <l.stach at pengutronix.de>
> ---
>  .../dts/freescale/imx8mp-debix-model-a.dts    | 57 +++++++++++++++++++
>  1 file changed, 57 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
> index 2876d18f2a38..94dc089e4550 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
> @@ -43,6 +43,17 @@ reg_usdhc2_vmmc: regulator-usdhc2 {
>  		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
>  		enable-active-high;
>  	};
> +
> +	reg_usb_hub: regulator-usb-hub {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_usb_hub>;
> +		regulator-name = "USB_HUB";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpio4 26 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
>  };
>  
>  &A53_0 {
> @@ -254,6 +265,39 @@ &uart4 {
>  	status = "okay";
>  };
>  
> +&usb3_phy1 {
> +	status = "okay";
> +};
> +
> +&usb3_1 {
> +	status = "okay";
> +};
> +
> +&usb_dwc3_1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb1>;
> +	dr_mode = "host";
> +	status = "okay";

I had to fix it up by adding

	#address-cells = <1>;
	#size-cells = <0>;

Otherwise, DTC emits reg_format warnings.

/soc at 0/usb at 32f10108/usb at 38200000/hub at 1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
/soc at 0/usb at 32f10108/usb at 38200000/hub at 2:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)

Shawn

> +
> +	/* 2.x hub on port 1 */
> +	usb_hub_2_x: hub at 1 {
> +		compatible = "usbbda,5411";
> +		reg = <1>;
> +		reset-gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
> +		vdd-supply = <&reg_usb_hub>;
> +		peer-hub = <&usb_hub_3_x>;
> +	};
> +
> +	/* 3.x hub on port 2 */
> +	usb_hub_3_x: hub at 2 {
> +		compatible = "usbbda,411";
> +		reg = <2>;
> +		reset-gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
> +		vdd-supply = <&reg_usb_hub>;
> +		peer-hub = <&usb_hub_2_x>;
> +	};
> +};
> +
>  /* SD Card */
>  &usdhc2 {
>  	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> @@ -384,6 +428,12 @@ MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19				0x41
>  		>;
>  	};
>  
> +	pinctrl_reg_usb_hub: regusbhubgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI2_TXD0__GPIO4_IO26				0x19
> +		>;
> +	};
> +
>  	pinctrl_rtc_int: rtcintgrp {
>  		fsl,pins = <
>  			MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11				0x140
> @@ -411,6 +461,13 @@ MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX				0x49
>  		>;
>  	};
>  
> +	pinctrl_usb1: usb1grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR				0x10
> +			MX8MP_IOMUXC_SAI2_TXC__GPIO4_IO25				0x19
> +		>;
> +	};
> +
>  	pinctrl_usdhc2: usdhc2grp {
>  		fsl,pins = <
>  			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK				0x190
> -- 
> 2.30.2
>