[PATCH 4/7] phy: rockchip: Add naneng combo phy support for RK3588
Peter Geis
pgwipeout at gmail.com
Fri Mar 10 04:31:43 PST 2023
On Fri, Mar 10, 2023 at 3:05 AM Lucas Tanure <lucas.tanure at collabora.com> wrote:
>
> Add support for RK3588 combo phy
>
> This is based on prior work from XiaoDong Huang and
> Peter Geis fixing this issue specifically for Rockchip 356x.
>
> Co-developed-by: Andrew Powers-Holmes <aholmes at omnom.net>
> Signed-off-by: Andrew Powers-Holmes <aholmes at omnom.net>
> Signed-off-by: Lucas Tanure <lucas.tanure at collabora.com>
> ---
> .../rockchip/phy-rockchip-naneng-combphy.c | 184 ++++++++++++++++++
> 1 file changed, 184 insertions(+)
>
> diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> index 7b213825fb5d..7b8b001e4f9e 100644
> --- a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> +++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> @@ -63,6 +63,9 @@
> #define PHYREG18 0x44
> #define PHYREG18_PLL_LOOP 0x32
>
> +#define PHYREG27 0x6C
> +#define PHYREG27_RX_TRIM_RK3588 0x4C
> +
> #define PHYREG32 0x7C
> #define PHYREG32_SSC_MASK GENMASK(7, 4)
> #define PHYREG32_SSC_DIR_SHIFT 4
> @@ -114,7 +117,10 @@ struct rockchip_combphy_grfcfg {
> struct combphy_reg con2_for_sata;
> struct combphy_reg con3_for_sata;
> struct combphy_reg pipe_con0_for_sata;
> + struct combphy_reg pipe_con1_for_sata;
> struct combphy_reg pipe_xpcs_phy_ready;
> + struct combphy_reg pipe_pcie1l0_sel;
> + struct combphy_reg pipe_pcie1l1_sel;
> };
>
> struct rockchip_combphy_cfg {
> @@ -559,11 +565,189 @@ static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = {
> .combphy_cfg = rk3568_combphy_cfg,
> };
>
> +static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
> +{
> + const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> + unsigned long rate;
> + u32 val;
> +
> + switch (priv->type) {
> + case PHY_TYPE_PCIE:
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_pcie1l0_sel, true);
> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_pcie1l1_sel, true);
It's theoretically possible to have a different configuration than
both lanes being PCIe. If this exists yet in hardware I can't answer,
but you need to be able to support it. I recommend a similar solution
to what we applied to the PCIe3 phy driver.
> + break;
> + case PHY_TYPE_USB3:
> + /* Set SSC downward spread spectrum */
> + rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
> + PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
> + PHYREG32);
> +
> + /* Enable adaptive CTLE for USB3.0 Rx. */
> + val = readl(priv->mmio + PHYREG15);
> + val |= PHYREG15_CTLE_EN;
> + writel(val, priv->mmio + PHYREG15);
> +
> + /* Set PLL KVCO fine tuning signals. */
> + rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
> + PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT,
> + PHYREG33);
> +
> + /* Enable controlling random jitter. */
> + writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
> +
> + /* Set PLL input clock divider 1/2. */
> + rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
> + PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT,
> + PHYREG6);
> +
> + writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
> + writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
> +
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true);
> + break;
> + case PHY_TYPE_SATA:
> + /* Enable adaptive CTLE for SATA Rx. */
> + val = readl(priv->mmio + PHYREG15);
> + val |= PHYREG15_CTLE_EN;
> + writel(val, priv->mmio + PHYREG15);
> + /*
> + * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA.
> + * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm)
> + */
> + val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
> + val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
> + writel(val, priv->mmio + PHYREG7);
> +
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_sata, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_sata, true);
> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true);
> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con1_for_sata, true);
> + break;
> + case PHY_TYPE_SGMII:
> + case PHY_TYPE_QSGMII:
> + default:
> + dev_err(priv->dev, "incompatible PHY type\n");
> + return -EINVAL;
> + }
> +
> + rate = clk_get_rate(priv->refclk);
> +
> + switch (rate) {
> + case REF_CLOCK_24MHz:
> + if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
> + /* Set ssc_cnt[9:0]=0101111101 & 31.5KHz. */
> + val = PHYREG15_SSC_CNT_VALUE << PHYREG15_SSC_CNT_SHIFT;
> + rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
> + val, PHYREG15);
> +
> + writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
> + }
> + break;
> +
> + case REF_CLOCK_25MHz:
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_25m, true);
> + break;
> + case REF_CLOCK_100MHz:
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
> + if (priv->type == PHY_TYPE_PCIE) {
> + /* PLL KVCO fine tuning. */
> + val = 4 << PHYREG33_PLL_KVCO_SHIFT;
> + rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
> + val, PHYREG33);
> +
> + /* Enable controlling random jitter. */
> + writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
> +
> + /* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */
> + writel(PHYREG27_RX_TRIM_RK3588, priv->mmio + PHYREG27);
> +
> + /* Set up su_trim: */
> + writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
> + } else if (priv->type == PHY_TYPE_SATA) {
> + /* downward spread spectrum +500ppm */
> + val = PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT;
> + val |= PHYREG32_SSC_OFFSET_500PPM << PHYREG32_SSC_OFFSET_SHIFT;
> + rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
> + }
> + break;
> + default:
> + dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
> + return -EINVAL;
> + }
> +
> + if (priv->ext_refclk) {
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
> + if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
> + val = PHYREG13_RESISTER_HIGH_Z << PHYREG13_RESISTER_SHIFT;
> + val |= PHYREG13_CKRCV_AMP0;
> + rockchip_combphy_updatel(priv, PHYREG13_RESISTER_MASK, val, PHYREG13);
> +
> + val = readl(priv->mmio + PHYREG14);
> + val |= PHYREG14_CKRCV_AMP1;
> + writel(val, priv->mmio + PHYREG14);
> + }
> + }
> +
> + if (priv->enable_ssc) {
> + val = readl(priv->mmio + PHYREG8);
> + val |= PHYREG8_SSC_EN;
> + writel(val, priv->mmio + PHYREG8);
> + }
> +
> + return 0;
> +}
> +
> +static const struct rockchip_combphy_grfcfg rk3588_combphy_grfcfgs = {
> + /* pipe-phy-grf */
> + .pcie_mode_set = { 0x0000, 5, 0, 0x00, 0x11 },
> + .usb_mode_set = { 0x0000, 5, 0, 0x00, 0x04 },
> + .pipe_rxterm_set = { 0x0000, 12, 12, 0x00, 0x01 },
> + .pipe_txelec_set = { 0x0004, 1, 1, 0x00, 0x01 },
> + .pipe_txcomp_set = { 0x0004, 4, 4, 0x00, 0x01 },
> + .pipe_clk_25m = { 0x0004, 14, 13, 0x00, 0x01 },
> + .pipe_clk_100m = { 0x0004, 14, 13, 0x00, 0x02 },
> + .pipe_rxterm_sel = { 0x0008, 8, 8, 0x00, 0x01 },
> + .pipe_txelec_sel = { 0x0008, 12, 12, 0x00, 0x01 },
> + .pipe_txcomp_sel = { 0x0008, 15, 15, 0x00, 0x01 },
> + .pipe_clk_ext = { 0x000c, 9, 8, 0x02, 0x01 },
> + .pipe_phy_status = { 0x0034, 6, 6, 0x01, 0x00 },
> + .con0_for_pcie = { 0x0000, 15, 0, 0x00, 0x1000 },
> + .con1_for_pcie = { 0x0004, 15, 0, 0x00, 0x0000 },
> + .con2_for_pcie = { 0x0008, 15, 0, 0x00, 0x0101 },
> + .con3_for_pcie = { 0x000c, 15, 0, 0x00, 0x0200 },
> + .con0_for_sata = { 0x0000, 15, 0, 0x00, 0x0129 },
> + .con1_for_sata = { 0x0004, 15, 0, 0x00, 0x0000 },
> + .con2_for_sata = { 0x0008, 15, 0, 0x00, 0x80c1 },
> + .con3_for_sata = { 0x000c, 15, 0, 0x00, 0x0407 },
> + /* pipe-grf */
> + .pipe_con0_for_sata = { 0x0000, 11, 5, 0x00, 0x22 },
> + .pipe_con1_for_sata = { 0x0000, 2, 0, 0x00, 0x2 },
> + .pipe_pcie1l0_sel = { 0x0100, 0, 0, 0x01, 0x0 },
> + .pipe_pcie1l1_sel = { 0x0100, 1, 1, 0x01, 0x0 },
> +};
> +
> +static const struct rockchip_combphy_cfg rk3588_combphy_cfgs = {
> + .grfcfg = &rk3588_combphy_grfcfgs,
> + .combphy_cfg = rk3588_combphy_cfg,
> +};
> +
> static const struct of_device_id rockchip_combphy_of_match[] = {
> {
> .compatible = "rockchip,rk3568-naneng-combphy",
> .data = &rk3568_combphy_cfgs,
> },
> + {
> + .compatible = "rockchip,rk3588-naneng-combphy",
> + .data = &rk3588_combphy_cfgs,
> + },
> { },
> };
> MODULE_DEVICE_TABLE(of, rockchip_combphy_of_match);
> --
> 2.39.2
>
More information about the linux-arm-kernel
mailing list