[PATCH v3 5/6] soc: ti: pruss: Add helper function to enable OCP master ports

Roger Quadros rogerq at kernel.org
Wed Mar 8 00:41:48 PST 2023



On 06/03/2023 13:09, MD Danish Anwar wrote:
> From: Suman Anna <s-anna at ti.com>
> 
> The PRU-ICSS subsystem on OMAP-architecture based SoCS (AM33xx, AM437x
> and AM57xx SoCs) has a control bit STANDBY_INIT in the PRUSS_CFG register
> to initiate a Standby sequence (when set) and trigger a MStandby request
> to the SoC's PRCM module. This same bit is also used to enable the OCP
> master ports (when cleared). The clearing of the STANDBY_INIT bit requires
> an acknowledgment from PRCM and is done through the monitoring of the
> PRUSS_SYSCFG.SUB_MWAIT bit.
> 
> Add a helper function pruss_cfg_ocp_master_ports() to allow the PRU
> client drivers to control this bit and enable or disable the firmware
> running on PRU cores access to any peripherals or memory to achieve
> desired functionality. The access is disabled by default on power-up
> and on any suspend (context is not maintained).
> 
> Signed-off-by: Suman Anna <s-anna at ti.com>
> Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk at linaro.org>
> Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk at linaro.org>
> Signed-off-by: Puranjay Mohan <p-mohan at ti.com>
> ---
>  drivers/soc/ti/pruss.c           | 81 +++++++++++++++++++++++++++++++-
>  include/linux/remoteproc/pruss.h |  6 +++
>  2 files changed, 85 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/soc/ti/pruss.c b/drivers/soc/ti/pruss.c
> index 537a3910ffd8..dc3abda0b8c2 100644
> --- a/drivers/soc/ti/pruss.c
> +++ b/drivers/soc/ti/pruss.c
> @@ -22,14 +22,19 @@
>  #include <linux/remoteproc.h>
>  #include <linux/slab.h>
>  
> +#define SYSCFG_STANDBY_INIT	BIT(4)
> +#define SYSCFG_SUB_MWAIT_READY	BIT(5)
> +
>  /**
>   * struct pruss_private_data - PRUSS driver private data
>   * @has_no_sharedram: flag to indicate the absence of PRUSS Shared Data RAM
>   * @has_core_mux_clock: flag to indicate the presence of PRUSS core clock
> + * @has_ocp_syscfg: flag to indicate if OCP SYSCFG is present
>   */
>  struct pruss_private_data {
>  	bool has_no_sharedram;
>  	bool has_core_mux_clock;
> +	bool has_ocp_syscfg;
>  };
>  
>  /**
> @@ -205,6 +210,72 @@ int pruss_cfg_update(struct pruss *pruss, unsigned int reg,
>  }
>  EXPORT_SYMBOL_GPL(pruss_cfg_update);
>  
> +/**
> + * pruss_cfg_ocp_master_ports() - configure PRUSS OCP master ports
> + * @pruss: the pruss instance handle
> + * @enable: set to true for enabling or false for disabling the OCP master ports
> + *
> + * This function programs the PRUSS_SYSCFG.STANDBY_INIT bit either to enable or
> + * disable the OCP master ports (applicable only on SoCs using OCP interconnect
> + * like the OMAP family). Clearing the bit achieves dual functionalities - one
> + * is to deassert the MStandby signal to the device PRCM, and the other is to
> + * enable OCP master ports to allow accesses outside of the PRU-ICSS. The
> + * function has to wait for the PRCM to acknowledge through the monitoring of
> + * the PRUSS_SYSCFG.SUB_MWAIT bit when enabling master ports. Setting the bit
> + * disables the master access, and also signals the PRCM that the PRUSS is ready
> + * for Standby.
> + *
> + * Return: 0 on success, or an error code otherwise. ETIMEDOUT is returned
> + * when the ready-state fails.
> + */
> +int pruss_cfg_ocp_master_ports(struct pruss *pruss, bool enable)
> +{
> +	int ret;
> +	u32 syscfg_val, i;
> +	const struct pruss_private_data *data;
> +
> +	if (IS_ERR_OR_NULL(pruss))
> +		return -EINVAL;
> +
> +	data = of_device_get_match_data(pruss->dev);
> +
> +	/* nothing to do on non OMAP-SoCs */
> +	if (!data || !data->has_ocp_syscfg)
> +		return 0;
> +
> +	/* assert the MStandby signal during disable path */
> +	if (!enable)
> +		return pruss_cfg_update(pruss, PRUSS_CFG_SYSCFG,
> +					SYSCFG_STANDBY_INIT,
> +					SYSCFG_STANDBY_INIT);

You can omit the above if() if you just encapsulate the below in

if (enable) {


> +
> +	/* enable the OCP master ports and disable MStandby */
> +	ret = pruss_cfg_update(pruss, PRUSS_CFG_SYSCFG, SYSCFG_STANDBY_INIT, 0);
> +	if (ret)
> +		return ret;
> +
> +	/* wait till we are ready for transactions - delay is arbitrary */
> +	for (i = 0; i < 10; i++) {
> +		ret = pruss_cfg_read(pruss, PRUSS_CFG_SYSCFG, &syscfg_val);
> +		if (ret)
> +			goto disable;
> +
> +		if (!(syscfg_val & SYSCFG_SUB_MWAIT_READY))
> +			return 0;
> +
> +		udelay(5);
> +	}
> +
> +	dev_err(pruss->dev, "timeout waiting for SUB_MWAIT_READY\n");
> +	ret = -ETIMEDOUT;

}

> +
> +disable:
> +	pruss_cfg_update(pruss, PRUSS_CFG_SYSCFG, SYSCFG_STANDBY_INIT,
> +			 SYSCFG_STANDBY_INIT);
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(pruss_cfg_ocp_master_ports);
> +
>  static void pruss_of_free_clk_provider(void *data)
>  {
>  	struct device_node *clk_mux_np = data;
> @@ -495,10 +566,16 @@ static int pruss_remove(struct platform_device *pdev)
>  /* instance-specific driver private data */
>  static const struct pruss_private_data am437x_pruss1_data = {
>  	.has_no_sharedram = false,
> +	.has_ocp_syscfg = true,
>  };
>  
>  static const struct pruss_private_data am437x_pruss0_data = {
>  	.has_no_sharedram = true,
> +	.has_ocp_syscfg = false,
> +};
> +
> +static const struct pruss_private_data am33xx_am57xx_data = {
> +	.has_ocp_syscfg = true,
>  };

How about keeping platform data for different platforms separate?

i.e. am33xx_pruss_data and am57xx_pruss_data

>  
>  static const struct pruss_private_data am65x_j721e_pruss_data = {
> @@ -506,10 +583,10 @@ static const struct pruss_private_data am65x_j721e_pruss_data = {
>  };
>  
>  static const struct of_device_id pruss_of_match[] = {
> -	{ .compatible = "ti,am3356-pruss" },
> +	{ .compatible = "ti,am3356-pruss", .data = &am33xx_am57xx_data },
>  	{ .compatible = "ti,am4376-pruss0", .data = &am437x_pruss0_data, },
>  	{ .compatible = "ti,am4376-pruss1", .data = &am437x_pruss1_data, },
> -	{ .compatible = "ti,am5728-pruss" },
> +	{ .compatible = "ti,am5728-pruss", .data = &am33xx_am57xx_data },
>  	{ .compatible = "ti,k2g-pruss" },
>  	{ .compatible = "ti,am654-icssg", .data = &am65x_j721e_pruss_data, },
>  	{ .compatible = "ti,j721e-icssg", .data = &am65x_j721e_pruss_data, },
> diff --git a/include/linux/remoteproc/pruss.h b/include/linux/remoteproc/pruss.h
> index 7952f250301a..8cb99d3cad0d 100644
> --- a/include/linux/remoteproc/pruss.h
> +++ b/include/linux/remoteproc/pruss.h
> @@ -168,6 +168,7 @@ int pruss_release_mem_region(struct pruss *pruss,
>  int pruss_cfg_read(struct pruss *pruss, unsigned int reg, unsigned int *val);
>  int pruss_cfg_update(struct pruss *pruss, unsigned int reg,
>  		     unsigned int mask, unsigned int val);
> +int pruss_cfg_ocp_master_ports(struct pruss *pruss, bool enable);
>  
>  #else
>  
> @@ -203,6 +204,11 @@ static inline int pruss_cfg_update(struct pruss *pruss, unsigned int reg,
>  	return -EOPNOTSUPP;
>  }
>  
> +static inline int pruss_cfg_ocp_master_ports(struct pruss *pruss, bool enable)
> +{
> +	return -EOPNOTSUPP;
> +}
> +
>  #endif /* CONFIG_TI_PRUSS */
>  
>  #if IS_ENABLED(CONFIG_PRU_REMOTEPROC)

cheers,
-roger



More information about the linux-arm-kernel mailing list