[PATCH V2 4/9] ARM: dts: imx28-cfa10036: Convert to use label references
Stefan Wahren
stefan.wahren at i2se.com
Tue Mar 7 10:40:02 PST 2023
These Crystal fontz board files still use node name and unit
address to reference parts from the imx28.dtsi . This causes
a lot of redundancy. So use label references in order to make
it easier to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren at i2se.com>
Cc: Brian Lilly <brian at crystalfontz.com>
Cc: Michal Vokáč <michal.vokac at ysoft.com>
---
arch/arm/boot/dts/imx28-cfa10036.dts | 193 ++++++------
arch/arm/boot/dts/imx28-cfa10049.dts | 454 +++++++++++++--------------
arch/arm/boot/dts/imx28-cfa10055.dts | 224 +++++++------
arch/arm/boot/dts/imx28-cfa10056.dts | 146 +++++----
arch/arm/boot/dts/imx28-cfa10057.dts | 252 +++++++--------
arch/arm/boot/dts/imx28-cfa10058.dts | 186 ++++++-----
6 files changed, 703 insertions(+), 752 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
index 85aa1cc3ff66..d004b1cbb4ae 100644
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ b/arch/arm/boot/dts/imx28-cfa10036.dts
@@ -16,107 +16,6 @@ memory at 40000000 {
reg = <0x40000000 0x08000000>;
};
- apb at 80000000 {
- apbh at 80000000 {
- pinctrl at 80018000 {
- ssd1306_cfa10036: ssd1306-10036 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP0_DATA7__GPIO_2_7
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins_cfa10036: leds-10036 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_AUART1_RX__GPIO_3_4
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- usb0_otg_cfa10036: otg-10036 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_RDY0__USB0_ID
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mmc_pwr_cfa10036: mmc_pwr_cfa10036 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- 0x31c3 /*
- MX28_PAD_PWM3__GPIO_3_28 */
- >;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
- };
-
- };
-
- ssp0: spi at 80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- vmmc-supply = <®_vddio_sd0>;
- bus-width = <4>;
- status = "okay";
- };
- };
-
- apbx at 80040000 {
- duart: serial at 80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_b>;
- status = "okay";
- };
-
- i2c0: i2c at 80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_b>;
- clock-frequency = <400000>;
- status = "okay";
-
- ssd1306: oled at 3c {
- compatible = "solomon,ssd1306fb-i2c";
- pinctrl-names = "default";
- pinctrl-0 = <&ssd1306_cfa10036>;
- reg = <0x3c>;
- reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
- solomon,height = <32>;
- solomon,width = <128>;
- solomon,page-offset = <0>;
- solomon,com-lrremap;
- solomon,com-invdir;
- solomon,com-offset = <32>;
- };
- };
-
- usbphy0: usbphy at 8007c000 {
- status = "okay";
- };
- };
- };
-
- ahb at 80080000 {
- usb0: usb at 80080000 {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_otg_cfa10036>;
- dr_mode = "peripheral";
- phy_type = "utmi";
- status = "okay";
- };
- };
-
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -138,3 +37,95 @@ reg_vddio_sd0: vddio-sd0 {
gpio = <&gpio3 28 0>;
};
};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_b>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_b>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ ssd1306: oled at 3c {
+ compatible = "solomon,ssd1306fb-i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssd1306_cfa10036>;
+ reg = <0x3c>;
+ reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+ solomon,height = <32>;
+ solomon,width = <128>;
+ solomon,page-offset = <0>;
+ solomon,com-lrremap;
+ solomon,com-invdir;
+ solomon,com-offset = <32>;
+ };
+};
+
+&pinctrl {
+ ssd1306_cfa10036: ssd1306-10036 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA7__GPIO_2_7
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins_cfa10036: leds-10036 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART1_RX__GPIO_3_4
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ usb0_otg_cfa10036: otg-10036 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_RDY0__USB0_ID
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mmc_pwr_cfa10036: mmc_pwr_cfa10036 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x31c3 /*
+ MX28_PAD_PWM3__GPIO_3_28 */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ vmmc-supply = <®_vddio_sd0>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&usb0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_otg_cfa10036>;
+ dr_mode = "peripheral";
+ phy_type = "utmi";
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 9ef0d567ea48..94d6614c1983 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -78,226 +78,6 @@ pca9555: pca9555 at 20 {
};
};
- apb at 80000000 {
- apbh at 80000000 {
- pinctrl at 80018000 {
- usb_pins_cfa10049: usb-10049 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- i2cmux_pins_cfa10049: i2cmux-10049 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D22__GPIO_1_22
- MX28_PAD_LCD_D23__GPIO_1_23
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- mac0_pins_cfa10049: mac0-10049 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SS2__GPIO_2_21
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- pca_pins_cfa10049: pca-10049 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SS0__GPIO_2_19
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- rotary_pins_cfa10049: rotary-10049 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_I2C0_SCL__GPIO_3_24
- MX28_PAD_I2C0_SDA__GPIO_3_25
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- rotary_btn_pins_cfa10049: rotary-btn-10049 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SAIF1_SDATA0__GPIO_3_26
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- spi2_pins_cfa10049: spi2-cfa10049 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SCK__GPIO_2_16
- MX28_PAD_SSP2_MOSI__GPIO_2_17
- MX28_PAD_SSP2_MISO__GPIO_2_18
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- spi3_pins_cfa10049: spi3-cfa10049 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_RDN__GPIO_0_24
- MX28_PAD_GPMI_RESETN__GPIO_0_28
- MX28_PAD_GPMI_CE1N__GPIO_0_17
- MX28_PAD_GPMI_ALE__GPIO_0_26
- MX28_PAD_GPMI_CLE__GPIO_0_27
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- lcdif_18bit_pins_cfa10049: lcdif-18bit at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D00__LCD_D0
- MX28_PAD_LCD_D01__LCD_D1
- MX28_PAD_LCD_D02__LCD_D2
- MX28_PAD_LCD_D03__LCD_D3
- MX28_PAD_LCD_D04__LCD_D4
- MX28_PAD_LCD_D05__LCD_D5
- MX28_PAD_LCD_D06__LCD_D6
- MX28_PAD_LCD_D07__LCD_D7
- MX28_PAD_LCD_D08__LCD_D8
- MX28_PAD_LCD_D09__LCD_D9
- MX28_PAD_LCD_D10__LCD_D10
- MX28_PAD_LCD_D11__LCD_D11
- MX28_PAD_LCD_D12__LCD_D12
- MX28_PAD_LCD_D13__LCD_D13
- MX28_PAD_LCD_D14__LCD_D14
- MX28_PAD_LCD_D15__LCD_D15
- MX28_PAD_LCD_D16__LCD_D16
- MX28_PAD_LCD_D17__LCD_D17
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10049: lcdif-evk at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10049_pullup: lcdif-10049-pullup at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RESET__GPIO_3_30
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- w1_gpio_pins: w1-gpio at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D21__GPIO_1_21
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
- };
- };
-
- lcdif at 80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_18bit_pins_cfa10049
- &lcdif_pins_cfa10049
- &lcdif_pins_cfa10049_pullup>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <18>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <9216000>;
- hactive = <320>;
- vactive = <480>;
- hback-porch = <2>;
- hfront-porch = <2>;
- vback-porch = <2>;
- vfront-porch = <2>;
- hsync-len = <15>;
- vsync-len = <15>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
-
- apbx at 80040000 {
- pwm: pwm at 80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pins_b>;
- status = "okay";
- };
-
- i2c1: i2c at 8005a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
- };
-
- usbphy1: usbphy at 8007e000 {
- status = "okay";
- };
-
- lradc at 80050000 {
- status = "okay";
- fsl,lradc-touchscreen-wires = <4>;
- };
- };
- };
-
- ahb at 80080000 {
- usb1: usb at 80090000 {
- vbus-supply = <®_usb1_vbus>;
- pinctrl-0 = <&usb1_pins_a>;
- pinctrl-names = "default";
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -315,18 +95,6 @@ reg_usb1_vbus: regulator at 0 {
};
};
- ahb at 80080000 {
- mac0: ethernet at 800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a
- &mac0_pins_cfa10049>;
- phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
- };
-
spi-2 {
compatible = "spi-gpio";
pinctrl-names = "default";
@@ -426,3 +194,225 @@ onewire {
gpios = <&gpio1 21 0>;
};
};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_18bit_pins_cfa10049
+ &lcdif_pins_cfa10049
+ &lcdif_pins_cfa10049_pullup>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9216000>;
+ hactive = <320>;
+ vactive = <480>;
+ hback-porch = <2>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vfront-porch = <2>;
+ hsync-len = <15>;
+ vsync-len = <15>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a
+ &mac0_pins_cfa10049>;
+ phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
+
+&pinctrl {
+ usb_pins_cfa10049: usb-10049 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ i2cmux_pins_cfa10049: i2cmux-10049 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D22__GPIO_1_22
+ MX28_PAD_LCD_D23__GPIO_1_23
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_pins_cfa10049: mac0-10049 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SS2__GPIO_2_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ pca_pins_cfa10049: pca-10049 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SS0__GPIO_2_19
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ rotary_pins_cfa10049: rotary-10049 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ rotary_btn_pins_cfa10049: rotary-btn-10049 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF1_SDATA0__GPIO_3_26
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ spi2_pins_cfa10049: spi2-cfa10049 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ spi3_pins_cfa10049: spi3-cfa10049 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_RDN__GPIO_0_24
+ MX28_PAD_GPMI_RESETN__GPIO_0_28
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_ALE__GPIO_0_26
+ MX28_PAD_GPMI_CLE__GPIO_0_27
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ lcdif_18bit_pins_cfa10049: lcdif-18bit at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10049: lcdif-evk at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10049_pullup: lcdif-10049-pullup at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ w1_gpio_pins: w1-gpio at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D21__GPIO_1_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_b>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-0 = <&usb1_pins_a>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
index fac5bbda7a93..42ba7da48beb 100644
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ b/arch/arm/boot/dts/imx28-cfa10055.dts
@@ -14,121 +14,6 @@ / {
model = "Crystalfontz CFA-10055 Board";
compatible = "crystalfontz,cfa10055", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
- apb at 80000000 {
- apbh at 80000000 {
- pinctrl at 80018000 {
- spi2_pins_cfa10055: spi2-cfa10055 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SCK__GPIO_2_16
- MX28_PAD_SSP2_MOSI__GPIO_2_17
- MX28_PAD_SSP2_MISO__GPIO_2_18
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- lcdif_18bit_pins_cfa10055: lcdif-18bit at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D00__LCD_D0
- MX28_PAD_LCD_D01__LCD_D1
- MX28_PAD_LCD_D02__LCD_D2
- MX28_PAD_LCD_D03__LCD_D3
- MX28_PAD_LCD_D04__LCD_D4
- MX28_PAD_LCD_D05__LCD_D5
- MX28_PAD_LCD_D06__LCD_D6
- MX28_PAD_LCD_D07__LCD_D7
- MX28_PAD_LCD_D08__LCD_D8
- MX28_PAD_LCD_D09__LCD_D9
- MX28_PAD_LCD_D10__LCD_D10
- MX28_PAD_LCD_D11__LCD_D11
- MX28_PAD_LCD_D12__LCD_D12
- MX28_PAD_LCD_D13__LCD_D13
- MX28_PAD_LCD_D14__LCD_D14
- MX28_PAD_LCD_D15__LCD_D15
- MX28_PAD_LCD_D16__LCD_D16
- MX28_PAD_LCD_D17__LCD_D17
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10055: lcdif-evk at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10055_pullup: lcdif-10055-pullup at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RESET__GPIO_3_30
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
- };
-
- lcdif at 80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_18bit_pins_cfa10055
- &lcdif_pins_cfa10055
- &lcdif_pins_cfa10055_pullup>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <18>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <9216000>;
- hactive = <320>;
- vactive = <480>;
- hback-porch = <2>;
- hfront-porch = <2>;
- vback-porch = <2>;
- vfront-porch = <2>;
- hsync-len = <15>;
- vsync-len = <15>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
-
- apbx at 80040000 {
- lradc at 80050000 {
- fsl,lradc-touchscreen-wires = <4>;
- status = "okay";
- };
-
- pwm: pwm at 80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pins_b>;
- status = "okay";
- };
- };
- };
-
spi-2 {
compatible = "spi-gpio";
pinctrl-names = "default";
@@ -159,3 +44,112 @@ backlight {
default-brightness-level = <6>;
};
};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_18bit_pins_cfa10055
+ &lcdif_pins_cfa10055
+ &lcdif_pins_cfa10055_pullup>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9216000>;
+ hactive = <320>;
+ vactive = <480>;
+ hback-porch = <2>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vfront-porch = <2>;
+ hsync-len = <15>;
+ vsync-len = <15>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&pinctrl {
+ spi2_pins_cfa10055: spi2-cfa10055 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ lcdif_18bit_pins_cfa10055: lcdif-18bit at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10055: lcdif-evk at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10055_pullup: lcdif-10055-pullup at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_b>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
index c5f3337e8b39..0e15bdfd7281 100644
--- a/arch/arm/boot/dts/imx28-cfa10056.dts
+++ b/arch/arm/boot/dts/imx28-cfa10056.dts
@@ -13,81 +13,6 @@ / {
model = "Crystalfontz CFA-10056 Board";
compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
- apb at 80000000 {
- apbh at 80000000 {
- pinctrl at 80018000 {
- spi2_pins_cfa10056: spi2-cfa10056 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SCK__GPIO_2_16
- MX28_PAD_SSP2_MOSI__GPIO_2_17
- MX28_PAD_SSP2_MISO__GPIO_2_18
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_8mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
-
- lcdif_pins_cfa10056: lcdif-10056 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10056_pullup: lcdif-10056-pullup at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RESET__GPIO_3_30
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_ENABLE>;
- };
- };
-
- lcdif at 80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_cfa10056
- &lcdif_pins_cfa10056_pullup >;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <32000000>;
- hactive = <480>;
- vactive = <800>;
- hback-porch = <2>;
- hfront-porch = <2>;
- vback-porch = <2>;
- vfront-porch = <2>;
- hsync-len = <5>;
- vsync-len = <5>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
- };
-
spi-2 {
compatible = "spi-gpio";
pinctrl-names = "default";
@@ -111,3 +36,74 @@ hx8369: hx8369 at 0 {
};
};
};
+
+&pinctrl {
+ spi2_pins_cfa10056: spi2-cfa10056 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+
+ lcdif_pins_cfa10056: lcdif-10056 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10056_pullup: lcdif-10056-pullup at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_cfa10056
+ &lcdif_pins_cfa10056_pullup >;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <32000000>;
+ hactive = <480>;
+ vactive = <800>;
+ hback-porch = <2>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vfront-porch = <2>;
+ hsync-len = <5>;
+ vsync-len = <5>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
index 2f7e479dbc74..27602c01f162 100644
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ b/arch/arm/boot/dts/imx28-cfa10057.dts
@@ -14,126 +14,6 @@ / {
model = "Crystalfontz CFA-10057 Board";
compatible = "crystalfontz,cfa10057", "crystalfontz,cfa10036", "fsl,imx28";
- apb at 80000000 {
- apbh at 80000000 {
- pinctrl at 80018000 {
- usb_pins_cfa10057: usb-10057 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_18bit_pins_cfa10057: lcdif-18bit at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_D00__LCD_D0
- MX28_PAD_LCD_D01__LCD_D1
- MX28_PAD_LCD_D02__LCD_D2
- MX28_PAD_LCD_D03__LCD_D3
- MX28_PAD_LCD_D04__LCD_D4
- MX28_PAD_LCD_D05__LCD_D5
- MX28_PAD_LCD_D06__LCD_D6
- MX28_PAD_LCD_D07__LCD_D7
- MX28_PAD_LCD_D08__LCD_D8
- MX28_PAD_LCD_D09__LCD_D9
- MX28_PAD_LCD_D10__LCD_D10
- MX28_PAD_LCD_D11__LCD_D11
- MX28_PAD_LCD_D12__LCD_D12
- MX28_PAD_LCD_D13__LCD_D13
- MX28_PAD_LCD_D14__LCD_D14
- MX28_PAD_LCD_D15__LCD_D15
- MX28_PAD_LCD_D16__LCD_D16
- MX28_PAD_LCD_D17__LCD_D17
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10057: lcdif-evk at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- lcdif at 80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_18bit_pins_cfa10057
- &lcdif_pins_cfa10057>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <18>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <30000000>;
- hactive = <480>;
- vactive = <800>;
- hfront-porch = <12>;
- hback-porch = <2>;
- vfront-porch = <5>;
- vback-porch = <3>;
- hsync-len = <2>;
- vsync-len = <2>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
-
- apbx at 80040000 {
- lradc at 80050000 {
- fsl,lradc-touchscreen-wires = <4>;
- status = "okay";
- };
-
- pwm: pwm at 80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm4_pins_a>;
- status = "okay";
- };
-
- i2c1: i2c at 8005a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
- };
-
- usbphy1: usbphy at 8007e000 {
- status = "okay";
- };
- };
- };
-
- ahb at 80080000 {
- usb1: usb at 80090000 {
- vbus-supply = <®_usb1_vbus>;
- pinctrl-0 = <&usb1_pins_a>;
- pinctrl-names = "default";
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -151,17 +31,6 @@ reg_usb1_vbus: regulator at 0 {
};
};
- ahb at 80080000 {
- mac0: ethernet at 800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
- };
-
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 4 5000000>;
@@ -169,3 +38,124 @@ backlight {
default-brightness-level = <7>;
};
};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_18bit_pins_cfa10057
+ &lcdif_pins_cfa10057>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <30000000>;
+ hactive = <480>;
+ vactive = <800>;
+ hfront-porch = <12>;
+ hback-porch = <2>;
+ vfront-porch = <5>;
+ vback-porch = <3>;
+ hsync-len = <2>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
+
+&pinctrl {
+ usb_pins_cfa10057: usb-10057 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_18bit_pins_cfa10057: lcdif-18bit at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10057: lcdif-evk at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm4_pins_a>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-0 = <&usb1_pins_a>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
index 4465fd86785a..931c4d089b26 100644
--- a/arch/arm/boot/dts/imx28-cfa10058.dts
+++ b/arch/arm/boot/dts/imx28-cfa10058.dts
@@ -14,93 +14,6 @@ / {
model = "Crystalfontz CFA-10058 Board";
compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
- apb at 80000000 {
- apbh at 80000000 {
- pinctrl at 80018000 {
- usb_pins_cfa10058: usb-10058 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D07__GPIO_0_7
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_cfa10058: lcdif-10058 at 0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- lcdif at 80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_cfa10058>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <30000000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <40>;
- hfront-porch = <40>;
- vback-porch = <13>;
- vfront-porch = <29>;
- hsync-len = <8>;
- vsync-len = <8>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
-
- apbx at 80040000 {
- lradc at 80050000 {
- fsl,lradc-touchscreen-wires = <4>;
- status = "okay";
- };
-
- pwm: pwm at 80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pins_b>;
- status = "okay";
- };
-
- usbphy1: usbphy at 8007e000 {
- status = "okay";
- };
- };
- };
-
- ahb at 80080000 {
- usb1: usb at 80090000 {
- vbus-supply = <®_usb1_vbus>;
- pinctrl-0 = <&usb1_pins_a>;
- pinctrl-names = "default";
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -118,17 +31,6 @@ reg_usb1_vbus: regulator at 0 {
};
};
- ahb at 80080000 {
- mac0: ethernet at 800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
- };
-
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 3 5000000>;
@@ -136,3 +38,91 @@ backlight {
default-brightness-level = <6>;
};
};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_cfa10058>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <30000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <40>;
+ hfront-porch = <40>;
+ vback-porch = <13>;
+ vfront-porch = <29>;
+ hsync-len = <8>;
+ vsync-len = <8>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
+
+&pinctrl {
+ usb_pins_cfa10058: usb-10058 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_cfa10058: lcdif-10058 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_b>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-0 = <&usb1_pins_a>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
--
2.34.1
More information about the linux-arm-kernel
mailing list